RenesasメーカーR8C/17の使用説明書/サービス説明書
ページ先へ移動 of 28
REJ10J0746-01 10 RENESAS SINGLE-CHIP MICROCOMPUTER M16C FAMILY / R8C/Tiny SERIES Rev .1.10 Renesas Solutions Corp. Revision date : Mar 01, 2005 www .renesas.
1. These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corporation product best suited to the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Renesas Technology Corporation or a third party.
3 T able of Content s 1. accessory softwares to inst all 2. Until a sample program is operated with an emulator software P4 2.1 Flash programmer (Flash developm ent toolkit) Inst allation P4 2.2 Emulator Sof tware, C Compile r and High-performance Embedded Workshop Inst allations P10 2.
4 1. accessory softwares to install 1) Note the following point s before installing. a) The M3T -NC8C has already been installe d. b) The M3T -NC30WA has already been installed. c) The emulat or software h as already been installed. Install the sof tware attached to this product after uninst alling the above soft ware.
5 Click “OK”. Click “Next” Select language to be used and click "Ne xt".
6 Only when you agree w ith License Agreement , click "Y es". Click “Next”. Click “Next”..
7 Remove a check. Clic k “Next” Click “Next”. Refer to a new folder name, or select from the existing folder li st and Cli ck “Next”..
8 Refer to a new folder name, or select from the existing folder li st and Cli ck “Next”. Click “Next”. Click “Install”..
9 Click “finish”..
10 2.2 Emulator Sof tware, C Compiler and High-performance Embedded W orkshop Inst allations 1) Installation Double-click an inst aller of CD-ROM ¥ dlp_tool ¥. 2) Installation procedu res are described below . Select the language to be used and cli c k “Next”.
11 Only when you agree w ith License Agreement , click "Y es". Select all and click “Next” Refer to a new folder name, or select from the existing folder list and cli c k “Next”.
12 Refer to a new folder name, or select from the existing folder list and cli c k “Next”. Click “Y es” Check the setting before starting the inst allati on and if the setting is correct, click “Next”.
13 Check the setting before st arting the installation and if the setting is correct, click “Next”. Then, a copy will be started. Click “Finish”.
14 2.3 USB driver inst allation Connect the E8 emulator using the US B cable to the USB port of host ma chine. <Windows XP> Installation proce dures a re described below . If the E8 emulator is connected, it is recogni zed a s a new hardware. Click “Next” after sel ecting “Ins tall the sof tware automatically”.
15 Renesas USB drivers are not authenticated by Mi crosoft, but we provide them based on the sufficient examination. Insert CD-ROM and specif y ¥dlp_tool¥ DRIVERS¥USB¥XP¥.
16 <Windows 98/ME> Installation proce dures a re described below . If E8 emulator is connected, it is recognized as a ne w hard ware. Click “Next” and sta rt inst alling a driver . Put a check into “search for the be st driver for your device” and click “Next”.
17 Click “Next”. Click “Finish”. The installation is complet ed above..
18 2.4 Operate Sample Program 1) Copy ¥Jap anese¥M3A01 15_17¥PROGRAM¥ in CD-ROM to the given folder . 2) Change a file attribute Since the copied file attribute is set to “read-only”, cha nge it to the attribute which can be re ad or written .
19 Click “OK”. The installation is complet ed above..
20 <Windows 98/ME> Select all files in the copied folder by a mouse. Select “File” and “Property”. Remove a check of “Read-only” and click “Apply”.
21 Click “Close”. Perform this setting to files in all folders of “3min_timer” and “ad _on kai”. The installation is complet ed above..
22 3) Connect a t arget b oard Use a user cable to the E8 emulator and connect a t arget bo ard. Perform the below setting for the ju mper setting of a t arget board.
23 4) Compile a sample program The example of the musical scal e pro gram (ad_onkai.hws) is sho w n belo w . (1) S tart High-performance Embedded Workshop Select “program” of st art menu - “Renesas” - “High-perform ance Embedded Workshop” - “High-performance Embedded W orkshop” and click.
24 (4) Select “R5F21 174” for Device and put a check i nto “Download emulator firmware” for Mo de. Click “OK”. (5) When 5V power supply is perfo rmed from E8, put a check into “Powe r supply is carried out ”. Select 5.0V and click “OK”.
25 (3) Execute Click “Debug” - “Ex ecute ”. (4) If clicking “Debug” - “S top a prog ram”, a program will stop. When executing t he program again, click “Debug” - “Execute ”. <Musical Scale Program> When a program execution st art s, LED1(red) lights up.
REVISION HISTORY Description Rev . Date Page Summary 0.10 2004.08.18 - First edition issued 1.00 2005.02.01 - It changed from FDTlight to flash programmer (Flash Developm ent Toolkit).
R8C/15, R8C/17 StarterKit Tu t o r ia l Publication Date Rev.1.10 Mar 01, 2005 Published by: Renesas Solutions Corp. 4-1-6, Miyahara, Yodogawa-ku, Osaka City, 532-0003, Japa n ©2005 Rene sas Te chno logy Cor p. an d Rene sas Solu tion s Corp., Al l Righ ts Reser ved.
Renesas Solutions Cor p. 4-1-6, Miyahara, Y odoga wa -ku, Osaka City , 532-0003, Japan R8C/15, R8C/17 S tarterKit Tu t o r i a l.
デバイスRenesas R8C/17の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Renesas R8C/17をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはRenesas R8C/17の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Renesas R8C/17の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Renesas R8C/17で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Renesas R8C/17を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はRenesas R8C/17の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Renesas R8C/17に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちRenesas R8C/17デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
