RicohメーカーR3111x Seriesの使用説明書/サービス説明書
ページ先へ移動 of 44
R3111x SERIES LOW VOLTAGE DETECTOR NO.EA-056-080131 1 OUTLINE The R31 1 1x series are CMOS-based voltage dete ctor IC s with high detector thre shold accuracy and ultra-low supply current, which can be operated at an extremely lo w voltage and is used for system reset as an example.
R31 1 1x 2 BLOCK DIAGRAMS R31 1 1xxxxA R31 1 1xxxxB OUT V DD Vr e f GND OUT V DD Vr e f GND R31 1 1xxxxC OUT V DD GND Vr e f.
R 3 111 x 3 SELECTION GUIDE The package type, the detector thresh old, the output type and the taping type for the ICs can be selected at the users’ request.
R31 1 1x 4 PIN CONFIGURATIONS TO-92 SOT-89 SOT-23-3 SOT-23-5 SC-82AB SON1612- 6 3 12 (mark side) 3 12 (mark side) 1 2 3 (mark side) 123 4 5 (mark side) 43 1 2 (mark side) 1 2 3 6 5 4 (mark sid e ) PIN DESCRIPTIONS TO-92 SOT-89 SOT-23-3 Pin No.
R 3 111 x 5 ABSOLUTE MAXIMUM RATINGS Symbol Item Ratin g Unit V DD Supply Voltage 12 V V OUT1 Output Voltage (CMOS) V SS − 0.3 to V DD + 0.3 V V OUT2 Output Voltage (Nch) V SS − 0.
R31 1 1x 6 ELECTRICAL CHARACTERISTICS • R3111x09xA/C Topt = 25 ° C Symbol Item Conditions Min. Typ. Max. Unit − V DET Detector Threshold 0.882 0.900 0.918 V V HYS Detector Threshold Hysteresis 0.027 0.045 0.063 V I SS Supply Current V DD = 0.80V V DD = 2.
R 3 111 x 7 • R3111x27xA/C Topt = 25 ° C Symbol Item Conditions Min. Typ. Max. Unit − V DET Detector Threshold 2.646 2.700 2.754 V V HYS Detector Threshold Hysteresis 0.081 0.135 0.189 V I SS Supply Current V DD = 2.60V V DD = 4.70V 0.9 1.1 2.7 3.
R31 1 1x 8 • R3111x45xA/C Topt = 25 ° C Symbol Item Conditions Min. Typ. Max. Unit − V DET Detector Threshold 4.410 4.500 4.590 V V HYS Detector Threshold Hysteresis 0.135 0.225 0.315 V I SS Supply Current V DD = 4.34V V DD = 6.50V 1.1 1.3 3.3 3.
R 3 111 x 9 • R3111Q231B Topt = 25 ° C Symbol Item Conditions Min. Typ. Max. Unit − V DET Detector Threshold 2.254 2.300 2.346 V V HYS Detector Threshold Hysteresis 0.069 0.115 0.161 V I SS Supply Current V DD = 2.2V V DD = 4.3V 0.9 1.1 2.7 3.3 µ A V DDH Maximum Operating Volta ge 10 V Topt = 25 ° C 0.
R31 1 1x 10 TIMING CHART Detector Threshold t PLH t PLH t PLH GND GND V DDL - V DET +V DET Detect or T hreshold Released V oltage Minimum Operating V oltage Pull-up V oltage Supply Vo l t a g e (V DD .
R 3 111 x 11.
R31 1 1x 12 ELECTRICAL CHARACTERISTICS BY DETECTOR THRESHOLD • R3111x09x to R3111x60x Detector Threshold Detector Threshold Hysteresis Supply Current 1 Supply Current 2 − V DET [ V ] V HYS [ V ] I SS1 [ µ A ] I SS2 [ µ A ] Part Number Min. Typ. Max.
R 3 111 x 13 Output Current 1 * 3 Output Current 2 * 3 Output Dela y Time Minimum Operating Voltage Detector Threshold Temperature Coeffi cient I OUT1 [ mA ] I OUT2 [ mA ] t PLH [ µ s ] V DDL [ V ] ∆− V DET / ∆ Topt [ ppm/ ° C ] Condition Min.
R31 1 1x 14 OPERATION • Operation of R3111xxxxA Vr e f Ra Rb Rc V DD OUT GND Tr .1 Nch Com p arato r OUT pin shoul d be pulled- up to V DD or an ext ernal voltage level.
R 3 111 x 15 • Operation of R3111xxxxB Vr e f Ra Rb Rc V DD OUT GND Tr .1 Nch Com p arato r OUT pin shoul d be pulled- up to V DD or an ext ernal voltage level.
R31 1 1x 16 • Operation of R3111xxxxC Vr e f Ra Rb Rc V DD OUT GND Tr . 1 Nch Pch Com p arato r Block Diagram (R31 1 1 xxxxC) t PLH GND GND V DDL - V DET +V DET Detector Threshold Released V oltage .
R 3 111 x 17 TEST CIRCUITS GND V DD V IN I SS R 3 111 x Series OUT GND V DD V IN R 3 111 x Series OUT 470k Ω 5V V OUT Supply Current T est Circuit Detector Threshold T est Circuit (Pull-up circuit is not neces sary for CMOS Output type.
R31 1 1x 18 TYPICAL CHARACTERISTICS 1) Supply Current vs. Input Voltage R31 1 1x09xC R31 1 1x27xC T opt=85 ° C 25 ° C -40 ° C 2.5 2.0 1.5 1.0 0.5 0.0 Input V oltage V IN (V) 02 4 6 8 1 0 Supply Current I SS ( µ A) T opt=85 ° C 25 ° C -40 ° C 2.
R 3 111 x 19 R31 1 1x45xC 4.8 4.7 4.6 4.5 4.4 +V DET -V DET T emperature T opt( ° C) - 6 0 0 2 04 06 08 0 -40 -20 100 Detector Threshold -V DET (V) 3) Output Voltage vs. Input Voltage R31 1 1x09xC R31 1 1x09xA T opt=-40 ° C 25 ° C 85 ° C 1.6 1.4 1.
R31 1 1x 20 R31 1 1x45xC R31 1 1x45xA T opt=-40 ° C 25 ° C 85 ° C 6 5 4 3 2 0 1 Input V oltage V IN (V) 02 3 16 5 4 Output V oltage V OUT (V) 5V Pull-up 470k Ω 6 5 4 3 2 0 1 Input V oltage V IN (V) 02 3 16 5 4 Output V oltage V OUT (V) T opt=-40 ° C 25 ° C 85 ° C 4) Nch Driver Output Current vs.
R 3 111 x 21 R31 1 1x45xC R31 1 1x45xC T opt=25 ° C V DD =4.5V 4.0V 3.5V 3.0V 2.5V 2.0V 1.5V 60 50 40 30 20 0 10 V DS (V) 0 0.5 1 1.5 2 2.5 3 4 3.5 4.5 Output Current I OUT (mA) V DD =0.8V 0.7V T opt=25 ° C 300 250 200 150 100 0 50 V DS (V) 0 0.02 0.
R31 1 1x 22 6) Pch Driver Output Current vs. Input Voltage R31 1 1x09xC R31 1 1x27xC T opt=25 ° C V DS =0.7V 0.5V 1.4 1.2 1.0 0.8 0.6 0.4 0.0 0.2 Input V oltage V IN (V) 024 68 Output Current I OUT (mA) T opt=25 ° C V DS =2.1V 1.5V 0.5V 1.0V 3.5 3.0 2.
R 3 111 x 23 R31 1 1x45xA t PLH t PHL 100 10 1 0.1 0.01 0.001 Load Capacitance C OUT ( µ F) 0.0001 0.01 0.001 0.1 Output Dela y Time tP(ms) 8) Output Delay Time vs. Input Pin Capacitance R31 1 1x09xA R31 1 1x27xA t PHL t PLH 100 10 1 0.1 0.01 0.001 Input Pin Capacitance C IN ( µ F) 0.
R31 1 1x 24 TYPICAL APPLICATION • R3111xxxxA CPU Res e t Circuit (Nch Open Drain Output) Case 1. Input Voltage to R3111xxxxA is equal to Input Voltage to CPU Case 2.
R 3 111 x 25 • Voltage level Indicator Circuit (lighted when the power runs out) (Nch Open Drain Output) R 3 111 x x x x A Series V DD GND OUT V DD • Detector Threshold Adjustable Circuit (Nch Ope.
R31 1 1x 26 TECHNICAL NOTES When R31 1 1xxxxA/B (Nch Open Drain Ou tput T ype) is used in Figure A or Figure B, if impedance of V oltage Supply pin, V DD and V DD of this IC is large, detector threshold level would shift by volt age dropdown caused by the consumption current of the IC itself.
P ACKAGE INFORMA TION PE-TO-92-061 1 • TO-92 (SC-43A) Unit: mm PACKAGE DIMENSIONS 5.2Max. 4.2Max. 2.3Max. 5.2Max. 12.7Min. 0.6Max. 0.55Max. 1.27 2.54 1 2 3 0.7 0.5Max. 5.2 Max. 4.2 Max. 2.3 Max. 5.2 Max. 12.7 Min. 0.6 Max. 0.55 1 2 3 0.5 Max. Max. 2.
P ACKAGE INFORMA TION PE-TO-92-061 1 POWER DISSIPATION (TO-92) This specification is at mounted on bo ard. Measurement Result (Topt=25 ° C,Tjm ax=125 ° C) Free Air Power Dissip ation 300mW Thermal Resist ance θ ja = (125 − 25 ° C)/0.
P ACKAGE INFORMA TION PE-SOT -89-071210 • SOT-89 (SC-62) Unit: mm PACKAGE DIMENSIONS 4.5 ± 0.1 0.4 ± 0.1 0.4 ± 0.1 1.5 ± 0.1 1.6 ± 0.2 1.5 ± 0.1 ± 0. 1 1.5 ± 0.1 2.5 ± 0.1 1.0 ± 0.2 0.3 ± 0.2 ∅ 1.0 12 3 3 2 1 0.4 2 ± 0.1 0. 4 7 0 .42 ± 0.
P ACKAGE INFORMA TION PE-SOT -89-071210 POWER DISSIPATION (SOT-89) This specification is at m ounted on board. Power Di ssipation (P D ) depends on conditions of mounting on board.
PA C K AGE INFORMA TION PE-SOT -23-5-071228 • SOT-23-5 (SC-74A) Unit: mm PACKAGE DIMENSIONS 2.9 ± 0.2 0.4 ± 0.1 1.9 ± 0.2 (0.95) (0.95) 54 12 3 +0.2 − 0.1 1.6 +0.2 − 0.1 1.1 +0.1 − 0.05 0.15 2.8–0.3 0 to 0.1 0.8 ± 0.1 0.2 Min. TAPING SPECIFICATION 2.
PA C K AGE INFORMA TION PE-SOT -23-5-071228 POWER DISSIPATION (SOT-23-5) This specification is at mou nted on board. Power Dissip ation (P D ) depends on conditions of mounting on board. This specification is based on the measurement at the condition below: (Power Dissip ation (S OT -23-5) is substitution of SOT -23-6.
P ACKAGE INFORMA TION PE-SOT -23-3-0510 • SOT-23-3 (SC-59A) Unit: mm PACKAGE DIMENSIONS 2.9 ± 0.2 0.4 ± 0.1 1.9 ± 0.2 (0.95) (0.95) 3 12 1.6 ± 0.2 +0.2 –0.1 1.1 +0.1 –0.06 0.16 2.8 ± 0.3 0.2 MIN. 0.8 0 to 0.1 1.4MAX. TAPING SPECIFICATION (T1: Standard Type) 2.
P ACKAGE INFORMA TION PE-SOT -23-3-0510 POWER DISSIPATION (SOT-23-3) This specification is at mou nted on board. Power Dissip ation (P D ) depends on conditions of mounting on board. This specification is based on the measurement at the condition below: (Power Dissip ation (SOT -23-3) is substitution of SOT -23-6.
P ACKAGE INFORMA TION PE-SC-82AB-0512 • SC-82AB Unit: mm PACKAGE DIMENSIONS 0.3 ± 0.2 3 2 1 4 1.3 ± 0.2 0.3 ± 0.1 0.3 ± 0.1 (0.7) 0.9 ± 0.1 0 to 0.1 0.3 ± 0.1 0.4 ± 0.1 0.05 0.16 +0.1 − 0.06 2 ± 0.2 2.1 ± 0.3 1.25 ± 0.2 − 0.1 TAPING SPECIFICATION 2.
P ACKAGE INFORMA TION PE-SC-82AB-0512 POWER DISSIPATION (SC-82AB) This specification is at mou nted on board. Power Dissip ation (P D ) depends on conditions of mounting on board.
P ACKAGE INFORMA TION PE-SON1612-6-0510 • SON1612-6 Unit: mm PACKAGE DIMENSIONS 64 13 1.6 ± 0.1 0.125 ± 0.055 0.22 ± 0.05 0.3TYP. 1.2 ± 0.05 0.6MAX. (0.2) (0.3) (0.3) 1.6 ± 0.05 0.08 0.5 0.08 M TAPING SPECIFICATION 1.5 +0.1 0 4.0 ± 0.1 1.75 1.
P ACKAGE INFORMA TION PE-SON1612-6-0510 Power Dissipation (SON1612-6) This specification is at mounted on board. Power Dissip ation (P D ) depends on conditions of mounting on board.
MARK INFORMA TION ME-R31 1 1E-0310 R3111E SERIES MARK SPECIFICATION • TO-92 (SC-43A) 1 2 3 4 5 6 7 8 9 10 11 12 1 to 5 : Series Name: R3111 (fixed) 6 , 7 : Detector Threshold: ex.
MARK INFORMA TION ME-R31 1 1H-0310 R3111H SERIES MARK SPECIFICATION • SOT-89 (SC-62) 1 2 3 4 5 6 1 to 4 : Product Code (refer to Part Number vs. Produ ct Code) 5 , 6 : Lot Number • Part Number vs.
MARK INFORMA TION ME-R31 1 1Nxx1-0310 R3111Nxx1 SERIES MARK SPECIFICATION • SOT-23-5 (SC-74A) 1 2 3 4 1 , 2 : Product Code (refer to Part Number vs. Produ ct Code) 3 , 4 : Lot Number • Part Number vs.
MARK INFORMA TION ME-R31 1 1Nxx2-0310 R3111Nxx2x SERIES MARK SPECIFICATION • SOT-23-3 (SC-59A) 1 2 3 4 1 , 2 : Product Code (refer to Part Number vs.
MARK INFORMA TION ME-R31 1 1Q-070918 R3111Q SERIES MARK SPECIFICATION • SC-82AB 2 4 1 3 1 , 2 : Product Code (refer to Part Number vs. Produ ct Code) 3 , 4 : Lot Number • Part Number vs.
MARK INFORMA TION ME-R31 1 1D-070918 R3111D SERIES MARK SPECIFICATION • SON1612-6 1 2 3 4 5 6 1 to 4 : Product Code (refer to Part Number vs. Product Code) 5 , 6 : Lot Number • Part Number vs.
デバイスRicoh R3111x Seriesの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Ricoh R3111x Seriesをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはRicoh R3111x Seriesの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Ricoh R3111x Seriesの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Ricoh R3111x Seriesで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Ricoh R3111x Seriesを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はRicoh R3111x Seriesの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Ricoh R3111x Seriesに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちRicoh R3111x Seriesデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。