RimageメーカーCDPR11の使用説明書/サービス説明書
ページ先へ移動 of 27
Rimage Prism Plus! TM User Guide.
.
Corporate Headquarters: Rimage Corporation 7725 Washington Avenue South Minneapolis, MN 55439 USA 800 553 8312 (toll free US) Service: +1 952 946 0004 (International) Fax: +1 952 944 6956 European Hea.
Rimage PrismPlus! Support information US, Asia/Pacific, Mexico/Latin America Europe Rimage Corporation 7725 Washington Avenue South Minneapolis, MN 55439 USA Attn: Rimage Services Service: North America: 800-553 -8 312 Asia/Pacific, Mexico/ Latin America: 952-946-0004 FAX: 952-946-6956 Rimage Support Website http://www.
Contents Contents Introduction ...................................................................................... 1 Operating system requirements ............................................................................ 1 Media requirements ...
Rimage PrismPlus! . ii.
Introduction Introduction This manual provides the information ne eded to set up, install, and operate the Prism Plus printer and to identify the parts. Operating system requirements The Rimage Prism Plus is compatible only with Windows 200 0, Windows XP, and Windows 2003 Server.
Rimage PrismPlus! 2 110635_G Identify the parts of the Prism Plus Front view Ribbon Guides Clamping Pins Drawer and Centering Pin Supply Roller Take-u p Rolle r Control panel There are four LEDs and an Operator Button on t he operator panel located o n the front of the printer.
Identify the parts of the PrismPlus Operator button This button opens and close s the printe r tray. There is a yellow LED in the center of this button. LED indicators The LED conditions descri bed bel ow reflect conditions on a Standalone Prism Plus .
Rimage PrismPlus! 4 110635_G Rear view.
Operate the PrismPlus Operate the Prism Plus Setting up a standalone Prism Plus Use these procedures to step up a standalone Prism Plus printer. Connecting the cables 1. Connect the parallel cable to the parallel cable connecti on at the back of the printer.
Rimage PrismPlus! 6 110635_G computer is connected to a network, a Local or Network Printe r dialog Play printer checkbox. splays. g. lect USB . h. Select Next . The Select manufacturer and model dialog displays. Installing the software To install CD Designer, place the CD De sign er disc in your PC disc tray and follo w the prompts.
Operate the PrismPlus 3. Select the printer driver file. a. Select Have Disk . The Install From Disk dialog opens. b. Select Browse . c. Navigate to the software CD included with your p rin ter. d. On the software CD, navigate: Printer Drivers > Prism > win2k_xp .
Rimage PrismPlus! 8 110635_G Powering on the printer 1. To power on the printer press the po wer sw it c h on the rear of the printer. The printer initializes.
Operate the PrismPlus Loading the discs 1. To open the printer tray, press the Operator bu tton . 2. Place one disc on the rubber pad between the two cl amping pi ns and the centering pin. - Important! Place the disc with the reco rding si de facing down.
Rimage PrismPlus! 10 110635_G Setting ribbon type, media type, and print strobe 1. Navigate to printing properties . 2. Select the Device Settings tab. 3. Select the type of Installed Ribbon . Note: Double Print is a feature that allows you to print the same lab el twice on the disc.
Operate the PrismPlus Printing in color 1. Install a multicolor ribbon in the printer. 2. Navigate to printing properties . 3. Select the Device Settings tab. 4. Select the Installed Ribbon setting. 5. Select Color, Three Panel CMY from the drop-down list.
Rimage PrismPlus! 12 110635_G Centering the image on the disc There are two ways to center the label. If the pr inter has a microparallel cable co nnection, and you have the Rimage serial cable, you can prog ram the offsets. If you do not have the serial cable, you can adjust the print position by changi ng the top and bottom margins.
Maintain the PrismPlus Maintain the Prism Plus General cleaning Cleaning the exterior Wipe the exterior of the printer with a lint free cloth. Cleaning the printhead Clean the printhead at every ribbon cha nge, or mo re often if streaks start appearing or the ri bb on has torn.
Rimage PrismPlus! 14 110635_G d. To close the tray and start the cleaning cycle, pre ss th e Operator button . When the cleaning cycle is complete , the tray opens. e. If necessary, repeat step d. f. Remove the cleaning pad w ith attached disc . g. Using a cotton s wab soaked in the clea ning solution, clean the front two ribbon guides.
Maintain the PrismPlus Replace consumables Changing the print ribbon # Tip: If ribbons are stored in an environ ment much diffe rent from that of the printer, allow plenty of time for them to become acclimated to the new environme nt. Allow more time for greater temperature and/or humidity differences.
Rimage PrismPlus! 16 110635_G f. Install the supply roller as shown. Leave some slack in the ribbon le ade r. g. Press the operator button until the printer tray comes out. The ribbon is threaded to the front of the Prism Plus . h. Remove the tape from the printer tray .
Maintain the PrismPlus f. Install the take-up roller in the Prism Plus and press down firmly until the take-up roller snaps into place. - Important! Do not roll the STOP - Wind Leader Onto Take -up Core Stopping here marking on the Ribbon Leader onto the t ake-up roller.
Rimage PrismPlus! 18 110635_G Learn more Prism Plus printer specifications Item Description Printing Speed 0.65 inches/second @ 300 x 300 dpi, typical 0.45 inches/second @ 300 x 600 dpi, typical Printing Direction Images are printed from a top to bottom orientation as the media is moving out of the machine.
Learn more Safety information This manual and the indications on the prod uct allo w proper and safe operation. The indication marks below help protect you and other person s from injury, and equipment from damage.
Rimage PrismPlus! 20 110635_G Safety testing Product name: Prism Plus Printer Model: cdprs Notice for USA Tested to Comply with FCC Standards FO R HOME OR OFFICE USE. NOTE: This equipment has been tested and f ound to comply with the limits for a Class B digital device, pursuant to Part 15 of the F CC Rules.
Learn more Rimage Prism Plus! TM Limited 6 Month Warranty . Rimage warrants, to the origi nal end user only , most parts of the Prism Plus! TM DISC Printer for 6 months, according to the following terms: • Rimage will replace or repair, at Rimage' s di scretion, any non-consumable parts foun d d efective within the Warranty period.
デバイスRimage CDPR11の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Rimage CDPR11をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはRimage CDPR11の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Rimage CDPR11の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Rimage CDPR11で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Rimage CDPR11を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はRimage CDPR11の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Rimage CDPR11に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちRimage CDPR11デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。