RolandメーカーAR-200Sの使用説明書/サービス説明書
ページ先へ移動 of 28
Owner’s Manual Thank you, and congratulations on your choice of the AR-200S Roland Audio Recorder. This manual mainly describes how to use the AR-200S as a playback device using CompactFlash cards that contain recordings made with other AR Series models.
2 USING THE UNIT SAFELY 001 • Before using this unit, make sure to read the instructions below, and the Owner’s Manual. ............................................................................................ 002c • Do not open (or modify in any way) the unit or its AC adaptor.
3 IMPORTANT NOTES 291a In addition to the items listed under “USING THE UNIT SAFELY” on page 2, please read and observe the following: Power Supply 301 • Do not connect this unit to same electri.
4 Contents USING THE UNIT SAFELY ......................................................................................... 2 IMPORTANT NOTES .................................................................................................. 3 Panel Descriptions .
5 Panel Descriptions fig.Panel.e Front Panel 1. PLAY/CLIP Indicator Lights during playback of phrases. Also lights during recording of phrases when the input level is too high (at clipping level). 2. REC Indicator Lights during recording of phrases. 3.
6 Installation Attach these as required, such as when you’re using the AR-200S without mounting it on a rack or the like. Peel off the double-sided tape from the rubber feet and affix the rubber feet at the locations shown in the following figure. fig.
7 Important Notes on Making Connections and Switching the Power On and Off 921 • To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any connections.
8 Examples of Usage and Connection for the AR-200S You can use the AR-200S alone or in combination with other AR-200S units or other equipment to play audio in a wide variety of scenes. This section shows some examples of these. You can use these examples as a starting point for making changes to match your own usage circumstances.
9 Examples of Usage and Connection for the AR-200S By connecting an RS-232C cable, you can control the AR-200S from an external control device, such as a computer or touch panel (p. 17). fig.Use-03.e There are several methods for doing this. Choose a playback method that matches your usage conditions.
10 Playback Instructions (Control Input Playback) You can use the control input and DC input screw terminals (CONTROL A) and the 25-pin D-sub-type control I/O connector (CONTROL B) on the AR- 200S’s rear panel to control the AR-200S from an external device.
11 Playback Instructions (Control Input Playback) Selecting the Control Input Mode With the power to the AR-200S switched off, set the MODE switches on the bottom panel as shown below. SW 1: OFF, SW 2: OFF Assigning Phrases to the Terminals Assign phrases 1 through 9 to Port Nos.
12 Playback Instructions (Control Input Playback) By inputting binary (Base 2) signals to Port Nos. 1 through 8 to select a phrase and inputting a start message to the START terminal, you can then play back the selected phrase. A maximum of 250 phrases can be selected and played back with this method.
13 Playback Instructions (Control Input Playback) The specified phrase will be played back at fixed intervals. Make each of the terminal settings beforehand for the playback interval and phrases to be played back. • When making settings in Interval Playback mode, assign Phrases 1 through 9 to the control output connectors 1 through 9.
14 Recording Instructions (Terminal Rec) In order perform recording matched to usage conditions, including the connected equipment, recording source, sound quality, time, and playback system, you make recording settings. • Recording settings are made in phrase units.
15 Recording Instructions (Terminal Rec) Select either stereo recording or mono recording. Choosing mono recording gives you recording times that are twice as long as with stereo recording. Selecting Recording Type With the power to the AR-200S turned off, set the REC MODE switches on the bottom panel as shown below.
16 Recording Instructions (Terminal Rec) Playback 9: 1 (On) 10: 0 (Off) The specified phrase is played back. Even when control signals are input continuously, the phrase is played back one time only and then ends. fig.CtrIn-Rec04.e * Playback does not begin if the binary-specified phrase is empty (the playback instruction is disabled).
17 About Control Using RS-232C The AR-200S can be controlled using serial communications from a computer, touch panel, or other device via RS-232C. You can control a number of operations including recording, playback, switching settings, and editing phrases.
18 Controlling Another Device with the AR-200S (Control Output Connectors) You can use the 25-pin D-sub-type control I/O connector (CONTROL B) on the AR-200S’s rear panel to control an external device from the AR-200S. The AR-200S outputs two kinds of control signals, Busy Out and Control Out.
19 Other Useful Functions During Phrase Playback Moreover, by using an optional AR-3000 to create and edit phrases, you can also use the following functions. For detailed information, please refer to the AR-3000 owner’s manual. * You cannot make settings for these parameters on the AR-200S.
20 Troubleshooting Control Input Playback (Direct/Binary) does not work as intended • Make sure the MODE switches’ settings (Direct/Binary) are selected correctly. You cannot achieve control input playback merely by connecting a device to the port.
21 Regarding Cards The following table shows recording times available for cards formatted for the AR-3000. * Recording times listed are for mono recording. Recording times are halved when data is recorded in stereo. * These times are for when 1 phrase is recorded continuously, and are provided for your reference when recording.
22 MODE SW Settings In addition to the REC MODE switches (p. 14), the AR-200S’s bottom panel also houses the MODE switches. Various applications are possible by changing the settings of the MODE switches. Each switch is ON when in the upward position, and OFF when in the downward position.
23 Control I/O Connector Specifications fig.ControlB • Control Input and DC Input Terminal (CONTROL A) “1, 2” are connected in parallel with Control I/O Connector (CONTROL B) “1, 2.” • When using Program Playback on a PC card created by the AR-3000, use connectors 1 (INC), 3 (DEC), 5 (EXCHANGE), 9 (START), and 10 (STOP).
24 Specifications AR-200S: Audio Recorder Recording Format RDAC (Roland Digital Audio Coding) RDAC-Grade (Sampling Rate) S-HIGH: 48 kHz HIGH: 44.1 kHz STANDARD: 32 kHz LONG1: 22.05 kHz LONG2: 16 kHz ANNOUNCE: 8 kHz Playback Rate Area S-HIGH: 20 Hz–22 kHz HIGH: 20 Hz–20 kHz STANDARD: 20 Hz–15 kHz LONG1: 20 Hz–10 kHz LONG2: 20 Hz–7.
25 Specifications Input Standard Output Standard * 0 dBu = 0.775 Vrms, -10 dBV = -7.79 dBu fig.Dimensions * Dimensions are with card inserted and rubber feet (included) attached.
26 Index B Binary Playback ............................................................. 12 Busy Out ......................................................................... 18 C Card Compatibility ....................................................
This product complies with the requirements of European Directive 89/336/EEC. For EU Countries For Canada This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
04012134 ’05-12-1N Information When you need repair service, call your nearest Roland Service Center or authorized Roland distributor in your country as shown below. As of December 10, 2005 (RSS) ASIA TAIWAN ROLAND TAIWAN ENTERPRISE CO., LTD. Room 5, 9fl.
デバイスRoland AR-200Sの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Roland AR-200Sをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはRoland AR-200Sの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Roland AR-200Sの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Roland AR-200Sで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Roland AR-200Sを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はRoland AR-200Sの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Roland AR-200Sに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちRoland AR-200Sデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
