RolandメーカーRS 232Cの使用説明書/サービス説明書
ページ先へ移動 of 60
2001.03 r AR-3000 audio recorder RS- 232C R eference AR- 3000 RS-232C Reference version 1.0 © 2001 c Unauthorized copying or reproduction of this manual in part or in whole is prohibited .
r AR-3000 RS-232C Reference - Contents - Section1 Introduction ....................................................................................................................... 1 1 .1 If You Have Been Using the AR-2000 ..........................
r AR-3000 RS-232C Reference L W Recorded P hrase P rotect M ode .......................................................................................... 12 SP System C opy .............................................................................
r AR-3000 RS-232C Reference EQ Equalizer S etting s ............................................................................................................... 27 VT Input Volume Thru S etting s ....................................................
r AR-3000 RS-232C Reference CR Card R emaining C apacity O utput ..................................................................................... 40 DC Display Contrast S etting O utput ............................................................
r AR-3000 RS-232C Reference - 1 Section1 Introduction This manual explains how to control the AR-3000 using RS-232C. For details on the operation of the AR-3000 itself, refer to the AR-3000 owner's manual. This manual assumes that you have a basic understanding of computers.
r AR-3000 RS-232C Reference - 2 2.3 Setup P rocedure Here is the procedure for setting up the external computer and the AR-3000. 1) Connections with the computer Use an RS-232C cable to connect the two devices. Refer to “ 2.4 Connections with the computer.
r AR-3000 RS-232C Reference - 3 Baud R ate S ettings Set the baud rate to the desired value. (Refer to owner's manual p.118) 1) Press the MODE button. 2) Rotate the SELECT knob to select “ 7.1 Baud rate. ” 3) Press the SELECT knob. 4) Rotate the SELECT knob to select the baud rate.
r AR-3000 RS-232C Reference - 4 a. The command is sent from the computer to the AR-3000. b. If the command was received correctly, the AR-3000 will transmit its settings as the Setting output command. If the command was received incorrectly, the AR-3000 will transmit an ER command.
r AR-3000 RS-232C Reference - 5 3.1.2 Command F ormat Commands (control signals) have several formats. Type 0: Those consisting only of a control code.
r AR-3000 RS-232C Reference - 6 Section4 Details of each C ommand 4.1 Commands T ransmitted from the E xternal D evice ( C omputer) to the AR-3000 The following 5 types of command are transmitted from the external device to the AR-3000. “ External ” in these explanations refers to the computer.
r AR-3000 RS-232C Reference - 7 3) Setting commands These commands are used to set AR-3000 parameters from the external device. 4) Request commands This command causes the AR-3000 to output the status of its current settings.
r AR-3000 RS-232C Reference - 8 = PL ( PLay) Function: Playback start Syntax: stx PL ; Note : If the playback phrase has not been specified, the minimum default value ( normally A001) will be used. The phrases specified by the PA command will be played back consecutively.
r AR-3000 RS-232C Reference - 9 Recording C ommands = AE ( Auto inc rEc start ) Function: Starting Time-stamped Recording Syntax: stxAE: *** * , ** , ** , ** , ** , ** , * ,* , * ; a b c d e f g h i a.
r AR-3000 RS-232C Reference - 10 = RM ( Rec Mode) Function: Record ready mode Syntax: stxRM: *** * , * , * , * , * , * , * ; a b c d e f g a Phrase number b RDAC-Grade 0 Announce 1 Long 2 2 Long 1 3 S.
r AR-3000 RS-232C Reference - 11 4.2.2 Editing C ommands = DM (Delete Mode) Function: Enable execution of editing commands. Syntax: stxDM ; Note : In order for editing commands to be executed, the DM command must be used to put the unit into Delete mode.
r AR-3000 RS-232C Reference - 12 = FM ( ForMat) Function: Format Card Syntax: stxDM ; stxFM: * , * , * ; a b c a Card in slot 0 Card in slot A 1 Card in slot B b Maximum number of phrase 0 250 1 500 2 1000 c Reserved ( 0 or 1 ) Example) FM :0,1,0; The card in slot A is formatted as follows ; the maximum number of phrases “ 500 ” .
r AR-3000 RS-232C Reference - 13 = SP (Setting coPy) Function: System copy Syntax: stxDM ; stxSP; Note: This copies the settings of the card in slot A to the card in slot B.
r AR-3000 RS-232C Reference - 14 > PV (Phrase diVide for AR-3000) Function: Divide Phrase Syntax: stxDM ; stxPV: ****,**H**M**S**F*S,*****,***** ; a b c d a Phrase number b divide time ( 0H0M0S0F0S - 23H59M59S**F9S ) c Write-destination Phrase number d Write-destination Phrase number Note: Only audio phrases can be specified.
r AR-3000 RS-232C Reference - 15 > RT (Recording - Type convert for AR-3000) Function: Recording - Type convert Syntax_1: (Stereo to Mono) stxDM; stxRT: 0,*****,***** ; a b c a Recording Type 0 Ste.
r AR-3000 RS-232C Reference - 16 4.2.3 Setting C ommands Card S ettings = CV (Card Volume label) Function: Card name setting Syntax: stxCV: * , “ ******** ” , ***** ; a b c a Card in slot 0 Card i.
r AR-3000 RS-232C Reference - 17 > PS (Pattern phrase Set up for AR-3000) Function: Pattern Phrase setting s Syntax_1: ( Sequence or Random 1 ) stxPS: **** , * ,*, *** ,*****,***, **S* , .
r AR-3000 RS-232C Reference - 18 Phrase S ettings < SU (phrase Set Up for AR-2000) Function: Phrase settings Syntax: stxSU: *** * , “ *********** ” , *** , **S* , * , **M**S , * , **M**S , *** .
r AR-3000 RS-232C Reference - 19 > PO (Phrase control Out set up for AR-3000) Function: Control Out settings Syntax: stx P O: *** * , *,**M**S; a b c a Phrase number b Control Out 0 OFF 1 ON c Offs.
r AR-3000 RS-232C Reference - 20 > VM(phrase VoluMe set up for AR - 3000) Function: play Volume settings Syntax: stxVM: **** * , ***; a b a Phrase number b Play Volume % (10 - 100) > FD (phrase .
r AR-3000 RS-232C Reference - 21 MIDI S ettings = MS (Midi Set up) Function: MIDI settings Syntax: stxMS: * , ** , * , * , ** ; a b c d e a Card in slot 0 Card in slot A 1 Card in slot B b MIDI Receiv.
r AR-3000 RS-232C Reference - 22 = NM (Note Map) Function: MIDI note map settings Syntax: stxNM: * , **** , ..... , *** * ; a 2 ..... 129 a Card in slot 0 Card in slot A 1 Card in slot B 2 – 129 : 1.
r AR-3000 RS-232C Reference - 23 System S ettings = BR (Baud Rate) Function: Communication speed setting Syntax: stxBR: * , * ; a b a Card in slot 0 Card in slot A 1 Card in slot B b Baud rate 0 (4800.
r AR-3000 RS-232C Reference - 24 = DP (Direct Play) Function: Direct Playback setting Syntax: stxDP: * , **** , **** , .... , *** * ; a b c .... q a Card in slot 0 Card in slot A 1 Card in slot B b - .
r AR-3000 RS-232C Reference - 25 < SM ( SysteM for AR-2000 ) Function: System settings Syntax: stxSM: * , * , * , * , * , * ; a b c d e f a Card in slot 0 Card in slot A 1 Card in slot B b Line Inp.
r AR-3000 RS-232C Reference - 26 d Binary Playback Trigger Settings Level 0 Off 1 On e Binary Playback Trigger Settings Edge 0 Off 1 On f The Method used for specifying the phrase ( Terminal Recording.
r AR-3000 RS-232C Reference - 27 > EQ ( E Q ualizer setup for AR-3000) Function: Equalizer setting Syntax: stxEQ: * , * , *** , * , *** , * , **; a b c d e f g a Card in slot 0 Card in slot A 1 Car.
r AR-3000 RS-232C Reference - 28 > DO (Display Off p arameter for AR-3000) Function: Display Parameter setting Syntax: stxDO: * , * , * , * ; ab c d a Card in slot 0 Card in slot A 1 Card in slot B b Display Sleep 0 Off 1 On c Sleep Time (0M30S - 59M59S) 4.
r AR-3000 RS-232C Reference - 29 = AQ (All reQuest) Function: Reset the Phrase Output Counter Syntax: stxAQ: * ; a a Card in slot 0 Card in slot A 1 Card in slot B 2 Note: This sets the Phrase Output Counter to the lowest-numbered phrase of the phrases registered in the card.
r AR-3000 RS-232C Reference - 30 = LQ ( dispLay contrast reQuest) Function: Display Contrast setting request Syntax: stxLQ ; Note: refer to DC command = MQ (Memory reQuest) Function: Card remaining ca.
r AR-3000 RS-232C Reference - 31 > QQ ( p hrase reQuest for AR-3000) Function1: Phrase setting contents request Syntax: stxQQ: *** * ; a a Phrase number Note: The phrase settings for the specified phrase number will be output. The value of the Phrase Output Counter (described below) will not change.
r AR-3000 RS-232C Reference - 32 = TQ (Time s tamp reQuest ) Function1: Time Stamp request Syntax: stxTQ: ****; a a Phrase number 0 Card in slot A 1 Card in slot B Note: Output the recording start time information for the specified phrase. (Refer to 4.
r AR-3000 RS-232C Reference - 33 4.2.5 Reply C ommands = ACK Function: Response to normal reception of a command Syntax: ACK (06H) = ER ( ERror) Function: Reply to the AR-3000 when an error has occurr.
r AR-3000 RS-232C Reference - 34 f Card ID (Created automatically) g Reserved Note: refer to CQ command Phrase S ettings < PU (Pattern phrase set Up for AR-2000 ) Function: Pattern Phrase setting output Syntax: stxPU: *** * , * , **** , **S* , ....
r AR-3000 RS-232C Reference - 35 < SU ( phrase Set Up for AR-2000 ) Function: Phrase setting output Syntax: stxSU: *** * , “ *********** ” , * , * , * , * , *** , **S* , * , **M**S , * , **M**S.
r AR-3000 RS-232C Reference - 36 > RU ( phRase s et Up for AR-3000) Function: Phrase setting output Syntax: stxRU: ***, ” ********* ” , * ,*,*,*,***,**S*,*, *, **M**S,*,**M**S,*, **S*,*,**S*, a.
r AR-3000 RS-232C Reference - 37 n Fade In Type 0 OFF 1 Time 1 2 Time 2 3 Time 3 4 ( 0S1 - 59S9 ) o Fade In Time ( 0S1 - 59S9 ) p Fade Out Type 0 OFF 1 Time 1 2 Time 2 3 Time 3 4 ( 0S1 - 59S9 ) q Fade.
r AR-3000 RS-232C Reference - 38 MIDI S ettings < MS (Midi Set up for AR-2000 ) Function: MIDI setting output Syntax: stxMS: * , ** , * , * , ** ; a b c d e a Card in slot 0 Card in slot A 1 Card i.
r AR-3000 RS-232C Reference - 39 h MIDI Expression 0 OFF 1 ON i MIDI Note Output 0 OFF 1 ON j MMC Mode 0 OFF 1 Master 2 Slave k Sync Source 0 Internal 1 MTC l Sync Out 0 Off 1 MTC m MTC Type 0 30 1 29.
r AR-3000 RS-232C Reference - 40 System S ettings = AC ( ACtive) Function: Active sensing reply Syntax: stxAC: * , **** ; a b a Status of AR-3000 0 During playback 1 During recording 2 During recording pause 3 During playback pause b Phrase number Note: During Dual Mono Mode, this is output twice.
r AR-3000 RS-232C Reference - 41 = DP (Direct Play) Function: Direct Playback setting output Syntax: stxDP: * , **** , **** , .... , *** * ; a b c .... q a Card in slot 0 Card in slot A 1 Card in slot B b - q Phrase number which you assigned to control input pin b CH1 c CH2 | q CH16 Note: For unused direct channels, “ ---- ” is output.
r AR-3000 RS-232C Reference - 42 > SY ( S Y stem for AR-3000 ) Function: System setting output Syntax: stxSY: * , * , * , * , * , * , * , * , * , * , * *S* , **S* , * , ** , * , ** , * , ** , * , *.
r AR-3000 RS-232C Reference - 43 s Input Volume Thru 0 Off 1 On t Busy Out - During Delay Time 0 Off 1 On u Busy Out - During Phrase Play 0 Off 1 On v Busy Out - During Repeat Int 0 Off 1 On w Display Sleep 0 Off 1 On x Display Sleep - Sleep Time ( 0M30S - 59M59S ) Note: refer to Y Q command = TI ( Time stamp Info.
r AR-3000 RS-232C Reference - 44 = CC (Card Condition) Function: Card insertion status output Syntax: stxCC: * , * ; a b a Status of card slot A 0 Not inserted 1 Inserted b Status of card slot B 0 Not inserted 1 Inserted Note: This is transmitted automatically when a card is inserted or removed.
r AR-3000 RS-232C Reference - 45 Note : When operation is paused with the PE command, the AR-3000 outputs the elapsed time from the start of the phrase to the point where paused.
r AR-3000 RS-232C Reference - 46 21 Unsupported card or Incorrect format. Please change cards or format card. 100 The AR-3000 received a “ 2Q ” or “ 3Q ” command even though the specified phrase was not a pattern phrase.
r AR-3000 RS-232C Reference - 47 Section5 Appendix 5.1 AR-3000 Commands L ist 5.1.1 AR-2000 Compatible Commands L ist # Commands transmitted from the external device (computer) to the AR-3000 # Contro.
r AR-3000 RS-232C Reference - 48 DQ Direct p layback reQuest Direct p layback setting contents request type2 IQ mIdi set up reQuest MIDI setting contents request type2 LQ dispLay contrast reQuest Disp.
r AR-3000 RS-232C Reference - 49 5.1.2 AR-3000 Commands ( C ommands N ewly A dded with the AR-3000) L ist # Commands transmitted from the external device (computer) to the AR-3000 # Editing C ommands .
r AR-3000 RS-232C Reference - 50 # Commands sent from the AR-3000 to the external device # Setting O utput C ommands # Phrase S ettings PS Pattern phra s e S et up Pattern p hrase setting output type2.
r AR-3000 RS-232C Reference - 51 5.3 Sample A lgorithms The following are some examples of processing algorithms. 5.3.1 Playing B ack a P hrase *1 Refer to the error number to determine the cause. Is the command format incorrect? *2 “ ACK ” will be output if the AR-3000 correctly recognizes the command.
r AR-3000 RS-232C Reference - 52 5.3.2 Recording ( Nomal Recording ) *1 Setting such as RDAC-Grade and RDAC-Mode are made by “ RM “ command parameters. Note : - You can check the operating status by transmitting the “ AC “ command. - You can stop recording by transmitting the “ ST “ command.
r AR-3000 RS-232C Reference - 53 5.3.3 Recording ( Time-Stamped Recording) *1 Setting such as RDAC-Grade and RDAC-Mode are made by “ AE “ command parameters.
r AR-3000 RS-232C Reference - 54 5.3.4 Verifying the P arameters ( D ata S ettings) of A ll P hrases S tarting with the L owest- N umbered Phrase *1 What is the Phrase Output Counter? The AR-3000 has an internal counter for phrase output. When a phrase is output, the phrase that corresponds to the AR-3000's counter will be output.
r AR-3000 RS-232C Reference - 55 5.3. 5 Deleting a P hrase *1 The AR-3000 will return the same “ PD “ command for confirmation. *2 By transmitting “ stxER :1: ” you can exit Delete mode.
デバイスRoland RS 232Cの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Roland RS 232Cをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはRoland RS 232Cの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Roland RS 232Cの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Roland RS 232Cで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Roland RS 232Cを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はRoland RS 232Cの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Roland RS 232Cに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちRoland RS 232Cデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
