Rose electronicsメーカーCrystalViewの使用説明書/サービス説明書
ページ先へ移動 of 36
CrystalView 10707 Stancliff Road Houston, Texas 77099 Phone: (281) 933 - 7673 Internet: WWW.ROSE.COM TM TWISTED PAIR KVM EXTENDER INSTALLATION AND OPERATIONS MANUAL.
TABLE OF CONTENTS Contents Disclaimer ................................................................................... 1 System introduction ..................................................................... 1 Features ..........................
LIMITED WARRANTY Copyright Rose Electronics 1990 - 2002. All rights re served. No part of this manual may be reproduced, stored in a retrieval system, or transcribed in any form or any means, electronic or mechanical, including photocopying and recording, without the prior written permission of Rose Electronics.
FCC/IC STATEMENTS, EU DECLARATION OF CONFORMITY CRYSTALVIEW INSTALLATION AND OPERATIONS MANUAL 31 FEDERAL COMMUNICATIONS COM MISSION AND INDUSTRY CANADA RADIO - FREQUENCY INTERFERENCE STATEMENTS This .
10707 Stancliff Road Houston, Texas 77099 Phone: (281) 933 - 7673 Internet: WWW.ROSE.COM.
Figures Fi gure 1. PC model ..................................................................... 4 Figure 2. Sun model .................................................................... 5 Figure 3. Serial/Audio model ...............................
INTRODUCTION CRYSTALVIEW INSTALLATION AND OPERATIONS MANUAL 1 Disclaimer While every precaution has been taken in the preparation of this manual, the manufacturer assumes no responsibility for errors or omissions. Neither does the manufacturer assume any liability for damages resulting from the use of the information contained herein.
CRYSTALVIEW INSTALLATION AND OPERATIONS MANUAL 2 Features n Extend a KVM station from a CPU using a single CAT - 5 twisted pair, solid core cable . (Up to 1,000 feet for the PC, SUN, PC - Serial/Audio models, 150 feet for the MINI mod el.) n Supports PC and SUN Systems.
CRYSTALVIEW INSTALLATION AND OPERATIONS MANUAL 3 Compatibility Com puters PCs with standard keyboards and PS/2 mice, 286, 386, 486, Pentium, etc. Monitors VGA, Super VGA, XGA, RGB (Sync - on - green) Keyboards CrystalView is compatible with most types of keyboard.
MODELS CRYSTALVIEW INSTALLATION AND OPERATIONS MANUAL 4 CrystalView PC - model Remote Unit Local Single Unit Remote Unit Local Dual Unit Figure 1 . PC model Connectors: Remote Unit § RJ45 – CAT - 5 cable connection. § HD15F – KVM stations video monito r connection.
CRYSTALVIEW INSTALLATION AND OPERATIONS MANUAL 5 CrystalView SUN model Remote Unit Lo cal Single Unit Remote Unit Local Dual Unit Figure 2 . Sun model Connectors: Remote Unit § RJ45 – CAT - 5 cable connection. § HD15F – KVM stations video monitor connection.
CRYSTALVIEW INSTALLATION AND OPERATIONS MANUAL 6 CrystalView PC - Serial/Audio model Remote Unit Local Single Unit Remote Unit Local Dual Unit Figure 3 . Serial/Audio model Conne ctors: Remote Unit § RJ45 – CAT - 5 cable connection. § HD15F – KVM stations video monitor connection.
CRYSTALVIEW INSTALLATION AND OPERATIONS MANUAL 7 CrystalView MINI model Remote Unit Loca l Single Unit Remote Unit Local Dual Unit Figure 4 . MINI model Connectors: Remote Unit § RJ45 – CAT - 5 cable connection. (Rear) § HD15F – KVM stations video monitor connection.
CABLES CRYSTALVIEW INSTALLATION AND OPERATIONS MANUAL 8 CrystalView cables CrystalView Local Unit to CPU cable CPU cables connect from the Local Unit to a CPUs keyboard, video monitor and mouse ports.
CRYSTALVIEW INSTALLATION AND OPERATIONS MANUAL 9 The CrystalView has been tested with all major makes of CAT - 5 cables, including BICC - VERO , Mohawk and AT&T . CrystalView has also been tested on CAT - 3 cable and on pairs within a 25 - pair UTP trunk cable.
INSTALLATION CRYSTALVIEW INSTALLATION AND OPERATIONS MANUAL 10 Installation Please refer to the safety section first before proceeding with any installation or configuration of the CrystalView. Installation of the CrystalView consists of four easy steps.
CRYSTALVIEW INSTALLATION AND OPERATIONS MANUAL 11 Step 1 – Setting the cable length jumpers/switch (PC, SUN, PC - Serial/Audio models. See Figure 5 .) There are three jumpers labeled JP3, JP4, and JP5, located on the Remote Units PCB. These t hree jumpers set the correct level of video equalization for different cable lengths.
CRYSTALVIEW INSTALLATION AND OPERATIONS MANUAL 12 PC / SUN / Serial/Audio MINI DAUGHTER BOARD O N SERIAL/AUDIO MODELS ONLY DIP SWITCH 1 Cable length Jumper Setting Cable length Switch 1 Setting 0 - 300 feet 0 - 75 feet OFF 301 - 600 feet 76 - 150 feet ON 601 - 1,000 feet N/A N/A Figure 5 .
CRYSTALVIEW INSTALLATION AND OPERATIONS MANUAL 13 Connect t he appropriate CPU cable to the keyboard, video monitor and mouse ports on the CPU and to the corresponding ports on the Local Unit. Connect the KVM stations keyboard, video monitor, and mouse cables to the corresponding connectors on the Remote Unit.
CRYSTALVIEW INSTALLATION AND OPERATIONS MANUAL 14 Connect the appropriate CPU cable to the keyboard, video monitor and mous e ports on the CPU and to the corresponding ports on the Local Unit.
CRYSTALVIEW INSTALLATION AND OPERATIONS MANUAL 15 Local unit to Remote unit cablin g (PC, SUN, PC - Serial/Audio Models) Connect up to 1,000 feet of CAT - 5 “solid core” cable from the Local Units “Twisted Pair Link” RJ45 connector to the Remote Units “Twisted Pair Link” RJ45 connector.
CRYSTALVIEW INSTALLATION AND OPERATIONS MANUAL 16 Step 4 – Adjusting the video compensation (PC, SUN, PC - Serial/Audio models only) (No video compensation is required for the MINI model) Video compensation adjustments should only be needed if your CAT - 5 cable length exceeds 3 00 feet.
CRYSTALVIEW INSTALLATION AND OPERATIONS MANUAL 17 User selectable settings (PC and SUN models) Dipswitch SW1 on the Remote Units PCB has four switches that allow you to change settings from their factory set values. SW1 settings only apply to the CrystalView Dual model.
CRYSTALVIEW INSTALLATION AND OPERATIONS MANUAL 18 Dual, PC - Serial/Audio model specific notes n Right control key = key to send commands to the CrystalView, changeable by SW1, position 2. n Console lockout period is fixed at 2 seconds. n Console switching is by pressing any key on the keyboard or by any mouse movement.
OPERATING INSTRUCTIONS CRYSTALVIEW INSTALLATION AND OPERATIONS MANUAL 19 Operating instructions - All units Once the Remote and Local Units are connected and configured, the Remote KVM station’s keyboard, video monitor and mouse will function as if it were directly connected to the CPU.
CRYSTALVIEW INSTALLATION AND OPERATIONS MANUAL 20 Reset This feature allows you to reset the mouse if it ever lock s up or is unplugged without having to boot the system. To reset the mouse, perform the commands for your model as shown in Table 4. If the mouse is still erratic after issuing the reset command, issue a Null Mouse command.
TROUBLESHOOTING CRYSTALVIEW INSTALLATION AND OPERATIONS MANUAL 21 Troubleshooting The troubleshooting section is used as a guid e to understanding the capabilities of the CrystalView and for general troubleshooting.
CRYSTALVIEW INSTALLATION AND OPERATIONS MANUAL 22 System does not detect PS/2 mouse or application cannot find mouse. n Keyboard and mouse cables reversed on the Local Unit .
CRYSTALVIEW INSTALLATION AND OPERATIONS MANUAL 23 Picture on monitor is black and white, not color. n The video cable was not attached to the PC when it was booted. Reboot the PC. A const ant vertical wobble appears down the screen. n The CAT - 5 cable connecting the Local and Remote Units could be located too close to a strong power source.
SERVICE CRYSTALVIEW INSTALLATION AND OPERATIONS MANUAL 24 Service Information Maintenance and Repair This Unit does not contain any internal u ser - serviceable parts. In the event a Unit needs repair or maintenance, you must first obtain a Return Authorization (RA) number from Rose Electronics or an authorized repair center.
SAFETY CRYSTALVIEW INSTALLATION AND OPERATIONS MANUAL 25 Safety The CrystalView KVM extender has been tested for conformance to safety regula tions and requirements, and has been certified for international use. Like all electronic equipment, the CrystalView should be used with care.
CRYSTALVIEW INSTALLATION AND OPERATIONS MANUAL 26 Safety and EMC Regulatory Statements Safety information Documentation reference symbol. If the product is marked with this symbol, refer to the product documentat ion to get more information about the product.
APPENDICES CRYSTALVIEW INSTALLATION AND OPERATIONS MANUAL 27 Appendix A. General specifications Video bandwidth (- 3db) Local Unit: 150 KHz Remote Unit: 300 KHz Over 300 feet UTP: 95Mhz w/equalization.
CRYSTALVIEW INSTALLATION AND OPERATIONS MANUAL 28 Appendix A1. Serial option specifications Baud Rate Up to 19,200 Baud Data Format Format Independent Flow Control RTS, CTS, DTR, DSR (Sent across link) Local Unit Connector DB9 Female (DCE) Remote Unit Connector DB9 Male (DTE) Appendix A2.
CRYSTALVIEW INSTALLATION AND OPERATIONS MANUAL 29 A ppendix C. Parts and cables Part Number Description CRK - 1P Single KVM station (PC) CRK - 2P Dual KVM station (PC) CRK - 1P/SUN Single KVM station .
CRYSTALVIEW INSTALLATION AND OPERATIONS MANUAL 30 Appendix E. Rack mount instructions CrystalView MINI model is not rack mountable. The optional rack mount kit includes the following items: n Two black anodized mounting brackets. n Four 6 - 32 x 3/8” flat head mounting screws.
デバイスRose electronics CrystalViewの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Rose electronics CrystalViewをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはRose electronics CrystalViewの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Rose electronics CrystalViewの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Rose electronics CrystalViewで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Rose electronics CrystalViewを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はRose electronics CrystalViewの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Rose electronics CrystalViewに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちRose electronics CrystalViewデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。