Rose electronicsメーカーswitch/hubの使用説明書/サービス説明書
ページ先へ移動 of 36
10707 Stancliff Road Phone: (281) 933 - 7673 Houston, Texas 77099 WWW.ROSE.COM VISTA KVM - SERIES INSTALLATION AND OPERATIONS MANUAL.
LIMITED WARRANTY Copyright Rose Electronics 1990 - 2001. All rights reserved. No part of this manual may be reproduced, stored in a retrieval system, or transcribed in any form or any means, electronic or mechanical, including photocopying and recording, without the prior written permission of Rose Electronics.
FCC/IC STATEMENTS, EU DECLARATION OF CONFORMITY FEDERAL COMMUNICATIONS COMMISSION AND INDUSTRY CANADA RADIO - FREQUENCY INTERFERENCE STATEMENTS This equipme nt generates, uses and can radiate radio fr.
TABLE OF CONTENTS Contents Disclaimer ................................................................................................ 1 Introduction .............................................................................................. 1 Product Registration .
INTRODUCTION Vista KVM - Series Installation and Operations Manual 1 Disclaimer While every precaution has been taken in the preparation of t his manual, the manufacturer assumes no responsibility for errors or omissions. Neither does the manufacturer assume any liability for damages resulting from the use of the information contained herein.
2 Vista KVM - Series Installation and Operations Manual Product Registration Take advantage of the following when you register your Rose Electronics products online at www.
Vista KVM - Series Installation and Operations Manual 3 Compatibility CPUs Computers Industry standard PCs, Unix computers such as RS - 6000, HP 9000, SGI, D EC Alpha, MAC and others Monitors SVGA Key.
OVER VIEW 4 Vista KVM - Series Installation and Operations Manual System overview The Vista KVM - series switch is designed to provide seamless, trouble - free switching from a single KVM station to any connected CPU. You can switch to the connected computers by simple keyboard commands or using the front panel buttons.
Vista KVM - Series Installation and Operations Manual 5 Figure 1 . Typical installati on Power connectors The optional power connector on the Vista switch is for a supplemental power adapter. Supplemental power may be needed if the cable length from the computers to the Vista switch is long or you are using a wireless keyboard and mouse.
MODELS 6 Vista KVM - Series Installation and Operations Manual Vista KVM - Series models Figure 2 . Vista 2 port Figure 3 . Vista 4 port Status LED Lit when selected CPU has power.
Vista KVM - Series Installation and Operations Manual 7 KVM - 2UPH rear connectors KVM - 4UPH rear connectors Label Connector type Description (2UPH) 1,2 DB25F Computer connectors (4UPH) 1,2,3,4 DB25F.
8 Vista KVM - Series Installation and Operations Manual KVM - 2PCA rear connectors KVM - 4PCA rear connectors Label Connector Type Description Keyboard (MiniDin - 6F) Mouse (MiniDin - 6F) Video (HD15F.
INSTALLATION Vista KVM - Series Installation and Operations Manual 9 Installation Installation of the Vista switch consists of the following steps: 1. Connect the KVM station to the Vista switch 2. Connect the CPUs to the Vista switch 3. Sequentially apply p ower, boot the CPUs 4.
10 Vista KVM - Series Installation and Operations Manual Step 2 - Connect the CPUs Connect the CPU keyboard, video monitor and mo use ports to the corresponding Vista switches keyboard, video monitor and mouse ports using the appropriate CPU cables as shown in Figure 5 .
Vista KVM - Series Installation and Operations Manual 11 Rack mounting The Vista switch is designed to mount in a CPU rack or under a desktop. Rackmount kits are available in three different sizes, 19", 23", and 24". Each is 1 rack unit high (1.
OPERATIONS 12 Vista KVM - Series Installation and Operations Manual Operating ins tructions The Vista switch is very easy to operate. Computer selection and set - up functions are entered from the keyboard. You can also select computers manually from the Vista’s front panel by using buttons 1 - 2 or buttons 1 - 4 depending on your model.
Vista KVM - Series Installation and Operations Manual 13 Keyboard commands (continued) Command Key Sequence Description Maximum computers <Ctrl> P x <Enter> (x = 1 – 2 or 1 – 4) Limits scanning t o maximum port number Typematic value <Ctrl> Ax <Enter> See Attachment F.
14 Vista KVM - Series Installation and Operations Manual Use only the numeric keys above the keyboard. The keypad will not work. All keyboard commands must be entered within 2 seconds of pressing and releasing the left <Ctrl> key.
Vista KVM - Series Installation and Operations Manual 15 Reset To “Reset” the mouse and keyboard, press and release the left <Ctrl> key, then type “R”. This command is used to reset the mouse and keyboard on the currently selected Vista port without removing power from the Vista switch.
16 Vista KVM - Series Installation and Operations Manual Maximum computers Press and release the left <Ctrl> key, type “P”, enter the total number of computers, and press <Enter>.
FLASH UPGRADE PROCEDURE Vista KVM - Series Installation and Operations Manual 17 KVM Flash Upgrade Utility Installation of KVM Utility The installer for the KVM Utility ma y be distributed in one of two formats: a ZIP file or an EXE. If the installer is distributed as a ZIP file, open it in WinZip and unzip the contents to a known location.
18 Vista KVM - Series Installation and Operations Manual 1. Download the flash upgrade firmwa re and unzip it to an .EXE file 2. Down load to a computer connected to port #1. 3. Run the unzipped “EXE” file . P rogram will auto - detect the unit 4.
Vista KVM - Series Installation and Operations Manual 19 8. When the firmware has been successfully installed the unit is now operat ional with the firmware upgrade. A more comprehensive explanation of the firmware upgrade process can be viewed by clicking on "Help".
TROUBLESHOOTING 20 Vista KVM - Series Installation and Operations Manual TroubleShooting CPU does not boot, keyboard or mouse error receiv ed • Cable is loose, reseat cable and hit F1 to continue or reboot computer. • Wrong cable plugged in, keyboard and mouse cables reversed.
Vista KVM - Series Installation and Operations Manual 21 Video fuzzy • Cable too long or wrong type. Use coax cable for high resolution. Mouse does not move • The Vista is turned off after or not connected when CPU was booted or the application using th e mouse was run.
SERVICE 22 Vista KVM - Series Installation and Operations Manual Mainten ance and repair This unit does not contain any internal user - serviceable parts. In the event a unit needs repair or maintenance, you must first obtain a Return Authorization (RA) number from Rose Electronics or an authorized repai r center.
SAF ETY Vista KVM - Series Installation and Operations Manual 23 Safety This Vista switch has been tested for co nformance to safety regulations and requirements, and has been certified for international use. Like all electronic equipment, the Vista switch should be used with care.
24 Vista KVM - Series Installation and Operations Manual Safety and EMC regulatory statements Safety Information Do cumentation reference symbol. If the product is marked with this symbol, refer to the product documentation to get more information about the product.
Vista KVM - Series Installation and Operations Manual 25 Safety and EMC regulatory statements Informations concernant la sécurité Symbole de référence à la documentation. Si le produit est marqué de ce symbole, reportez - vous à la documentation du produit afin d’obtenir des informations pl us détaillées.
APPENDICES 26 Vista KVM - Series Installation and Operations Manual Appendix A. Initial factory settings Setting Default Value Foreground Color White Background Color Blue X - position 45 Y - position.
Vista KVM - Series Installation and Operations Manual 27 Appendix B. Parts and cables Vista Part Numbers Description KVM - 2 /4 PCA 2 /4 - port w/PC connectors KVM - 2 / 4 UPH 2 /4 - port w/DB25 conne.
28 Vista KVM - Series Installation and Operations Manual Rackmount Kits RM - UM19 Black anodized, for installation in 19" racks. RM - UM23 Black anodized, for installation in 23" racks. RM - UM24 Black anodized, for installation in 24" racks.
Vista KVM - Series Installation and Operations Manual 29 Appendix D. Rack mount instructions The optional rack mount kit includes the following items: § Two black anodized mounting bracke ts.
30 Vista KVM - Series Installation and Operations Manual Appendix F. Typematic rate Ty pematic Command Press the left <Ctrl> key, type “A”, enter the typematic value (1 - 3 digit) followed by <Enter>. The typematic value is determined from the following tables using the equation: Typematic Value = Rate value + Delay Value.
.
10707 Stancliff Road Phone: (281) 933 - 7673 Houston, Texas 77099 WWW.ROSE.COM.
デバイスRose electronics switch/hubの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Rose electronics switch/hubをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはRose electronics switch/hubの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Rose electronics switch/hubの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Rose electronics switch/hubで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Rose electronics switch/hubを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はRose electronics switch/hubの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Rose electronics switch/hubに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちRose electronics switch/hubデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
