RyobiメーカーBS1001SVの使用説明書/サービス説明書
ページ先へ移動 of 28
OPERA TOR'S MANUAL 10 in. BAND SA W BS1001SV SA VE THIS MANUAL FOR FUTURE REFERENCE Y our new Band Saw has been engineered and manufactured to Ryobi's high standards for dependability , ease of operation, and operator safety . Properly car ed for , it will give you years of rugged, trouble-fr ee performance.
Page 2 n Introduction ...................................................................................................................................................................... 2 n General Safety Rules .....................................
Page 3 GENERAL SAFETY RULES n DO NOT OVE RREA CH. Keep prop er foot ing and bala nce at all times. n MAINTAIN TOOLS WITH CARE. Keep tools sharp and cle an for bes t and safe st perf orm ance . Follo w instr uct ions for lubricating and changing accessories.
Page 4 n BE SU RE THE BLAD E PAT H IS FR EE OF NA ILS . Ins pe ct for and remove nails from lumber before cutting. n AVOID AWKWARD OPERATIONS AND HAND POSITIONS where a sudden slip could cause your hand to move into the blade. ALWAYS make sure you have good balance.
Page 5 SYMBOLS Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpreta- tion of these symbols will allow you to operate the tool better and safer .
Page 6 SYMBOLS SERVICE Servicing r equires extr eme care and knowledge and should be performed only by a qualified service technician. For service we suggest you return the pr oduct to your near est AUTHORIZED SERVICE CENTER for r epair . When servic- ing, use only identical replacement parts.
Page 7 GLOSSAR Y OF TERMS Resaw A cutting operation to reduce the thickness of the workpiece to make thinner pieces. Resin A sticky , sap-based substance that has hardened. Ripping A cutting operation along the length of the workpiece. Saw Blade Path The area dir ectly in line — over , under , behind or in front of the blade.
Page 8 ELECTRICAL Fig. 1 GROUNDING PIN COVER OF GROUNDED OUTLET BOX EXTENSION CORDS Use only 3-wire extension cor ds that have 3-prong gr ound- ing plugs and 3-pole recept acles that accept the tool's plug.
Page 9 Fig. 2 FEA TURES DUST EXHAUST PORT TRACKING KNOB SCALE INDICA TOR BLADE GUIDE LOCK KNOB SCALE BEVEL ADJUSTMENT KNOB RAPIDSET™ BLADE TENSION LEVER SA W BLADE SWITCH AND SWITCH KEY BLADE TENSION KNOB LA TCH RIP FENCE MITER GAUGE SA W T ABLE BLADE GUARD BLADE GUIDE BEARING LED LIGHTING Input .
Page 10 FEA TURES LED LIGHTING Y our band saw comes equipped with LED lighting that lights the work area for safer , more accurate cuts. MITER GAUGE This gauge aligns the wood for a crosscut. The easy-to-rea d indicator shows the exact angle for a miter cut.
Page 11 Fig. 3 The following tools (not included) are needed for assembly and alignment: TOOLS NEEDED PHILLIPS SCREWDRIVER 10 mm WRENCH The following items are included with your band saw: LOOSE P AR TS LIST MITER GAUGE Fig. 4 Hex Key , 3 mm .........
Page 12 LOOSE P AR TS LIST LEG BRACE (LONG) FEET LEG LEG BRACE (SHORT) TOP BRACE (RIGHT) TOP BRACE (LEFT) Fig. 5 TOP BRACE (FRONT) TOP BRACE (BACK) LEG BRACE (LONG) LEG BRACE (SHORT) MOUNTING BOL T WASHER HEX NUT CARRIAGE BOL T HEX NUT CARRIAGE BOL T , SMALL HEX NUT , SMALL The following items are included with your band saw: Legs .
Page 13 ASSEMBL Y UNP ACKING This product r equires assembly . n Carefully remove the tool and any accessories from the box. Place it on a level work surface. NOTE: This tool is heavy . T o avoid back injury , lift with your legs, not your back, and get help when needed.
Page 14 ASSEMBL Y n Use the same steps to install the lower braces. Tighten all hex nuts with a wrench. n Place a carriage bolt in each of the four holes on the top of the leg stand and secure with a hex nut. n Tighten securely . n Place one foot on the bottom of each of the legs.
Page 15 ASSEMBL Y TO SQUARE THE SAW T ABLE TO THE BLADE See Figure 11. n T ur n the blade guide lock knob counterclockwise to unlo ck the blade guide assemb ly . T urning the blade guide knob clockwise, raise the blade guide assembly as far as it will go.
Page 16 ASSEMBL Y BLADE TENSION KNOB TO INCREASE TENSION TO DECREASE TENSION TO ADJUST BLADE TENSION See Figures 13 - 14. n Unplug the saw and remove the switch key . n Make sure RapidSet™ Blade T ension Lever is in the locked position. See Figure 14.
Page 17 OPERA TION W ARNING: Do not allow familiarity with tools to make you care- less. Remember that a careless fraction of a second is sufficient to inflict serious injury . WARNING: Always wear safety goggles or safety glasses with side shields when operating power tools.
Page 18 OPERA TION A VOIDING INJUR Y n Make sure saw is level and does not rock. Saw should always be on a firm, level surface with plenty of room for handling and properly supporting the workpiece. n Bolt saw to the support surface to prevent slipping, walking or sliding during operations like cutting long, heavy boards.
Page 19 OPERA TION TO EXTEND THE SAW T ABLE See Figure 17. The saw tabl e can be extend ed to incr eas e the work surf ace. T o lengthen the saw table: n Loosen the table lock knob under neath the saw table by turning counterclockwise. n Using the extension scale on the saw table, extend the saw table to the desired position.
Page 20 OPERA TION USING THE RIP FENCE See Figure 20. n Unplug the saw . n From either side of the saw blade, slide the rip fence onto the saw table. Check for a smooth, gliding action. n Push the locking handle down to automatically align and secure the fence.
Page 21 ADJUSTMENTS BLADE GUIDE ASSEMBL Y SA W BLADE UPPER WHEEL BLADE TENSION KNOB RAPIDSET™ BLADE TENSION LEVER LOWER WHEEL BLADE GUIDE ASSEMBL Y BLADE GUIDE KNOB BLADE GUIDE LOCK KNOB LOWER BLADE GUIDES Fig. 22 Fig. 23 n Carefully remove the old blade.
Page 22 ADJUSTMENTS W ARNING: T o avoid personal injury , maintain pr oper adjustment of blade tension, blade guides, and thrust bearings. n T o check tension, raise the blade guide assembly all the way up to expose the blade. n Push the blade to the side with moderate force; the blade should flex approximately 1/8 in.
Page 23 ADJUSTMENTS MITER GAUGE INDICA TOR SCREW T o Adjust Blade Guide Support: n Remove the blade guard by removing the two phillips screws that secur e it in place. n Adjust the position of the blade guide assembly . Loosen the bottom screw on the right side of the blade guide assembly using the 3 mm hex key .
Page 24 MAINTENANCE WARNING: When servicing, use only identical Ryobi replacement parts. Use of any other parts may create a hazard or cause product damage. WARNING: Always wear safety goggles or safety glasses with side sh iel ds dur ing pow er too l op era tio n or whe n bl owi ng dus t.
Page 25 MAINTENANCE BRUSHES See Figure 28. W ARNING: T o pr event accidental starting that could cause possible serious personal injury , tur n off the saw , remove the switch key , and unplug the saw befor e working on the band saw . The brushes located inside the saw housing on the door help protect the tir e and wheel by brushing off saw dust.
Page 26 TROUBLESHOOTING PROBLEM CAUSE SOLUTION Motor will not run. 1. Problem with On-Of f switch or 1. Have wor n parts replaced befor e power cord. using band saw again. 2. Motor defective. 2. Do not attempt any repair . Have tool repair ed by a qualified service technician.
Page 27 NOTES.
Page 28 983000-269 8 -04 R YOBI TECHNOLOGIES, INC. 1428 Pearman Dairy Road, Anderson SC 29625 Post Office Box 1207, Anderson SC 29622-1207 Phone 1-800-525-2579 www .ryobitools.com **Ampere rating (on tool data plate) 0-2.0 2.1-3.4 3.5-5.0 5.1-7.0 7.1-12.
デバイスRyobi BS1001SVの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Ryobi BS1001SVをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはRyobi BS1001SVの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Ryobi BS1001SVの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Ryobi BS1001SVで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Ryobi BS1001SVを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はRyobi BS1001SVの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Ryobi BS1001SVに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちRyobi BS1001SVデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。