RyobiメーカーHPL51の使用説明書/サービス説明書
ページ先へ移動 of 16
OPERA T OR'S MANU AL Power Planer Model No. HPL51 DOUBLE INSULA TED Y our new P ower Planer has been engineered and man ufactured to Ry obi’ s high standard f or dependability , ease of oper ation, and operator saf ety . Properly cared for , it will giv e you y ears of r ugged, trouble-free perf or mance.
Page 2 INTRODUCTION ■ ■ ■ ■ ■ Introduction ............................................................................................................................................................ 2 ■ ■ ■ ■ ■ General Safety Rules .
Page 3 GENERAL SAFETY RULES W ARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS Work Area ■ ■ ■ ■ ■ Keep your work area clean and well lit.
Page 4 GENERAL SAFETY RULES ■ When servicing a tool, use only identical replace- ment parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized par ts or failure to follow Maintenance Instructions may create a risk of electr ic shock or injury .
Page 5 SPECIFIC SAFETY RULES SYMBOLS W ARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm.
Page 6 SYMBOLS SA VE THESE INSTR UCTIONS The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger.
Page 7 Input 120 Volts, 60 Hz, AC only, 5 Amps No L oa d S pee d 16,000/min Maximum Planing Depth 3/32 in. (2.4 mm) Maximum Planing Width 3-1/4 in. (82 mm) Maximum Rabbet Depth 7/16 in. (11.1 mm) PR ODUCT SPECIFICA TIONS Blades Rapid Set™ Double-Edged Carbide (2) Weight 6 lbs.
Page 8 FEA TURES DEPTH ADJUSTMENT KNOB Fig. 1 EXHAUST PORT POWER CORD TRIGGER SWITCH EXHAUST DIRECTION DIAL FRONT HANDLE W ARNING: Do not allow familiarity with your planer to make you careless. Remember that being careless a fraction of a second is sufficient time to inflict severe injury.
Page 9 COLLAR DUST BAG EXHAUST PORT Fig. 2 ADJUSTMENTS Fig. 4 W ARNING: The power planer should never be connected to a power supply when you are assembling parts, making adjustments, cleaning, performing maintenance, or when the tool is not in use. Disconnecting the tool prevents accidental starting that could cause serious injury.
Page 10 Fig. 5 W ARNING: Always wear safety goggles or safety glasses with side shields when operating this tool. Failure to do so could result in dust, shavings, chips, loose particles, or foreign objects being thrown in your eyes resulting in possible serious injury.
Page 11 OPERA TION Fig. 8 PLANING See Figure 7. Follow these steps to plane. 1. Clamp the work securely. 2. Adjust the planing depth. Refer to “Adjusting the Plan- ing Depth” earlier in this manual. 3. Hold the front handle with your left hand and the rear handle with your right hand.
Page 12 Fig. 9 Fig. 10 OPERA TION PLANING EDGES AND MAKING RABBET CUTS The planer comes with an adjustable edge guide for precision edge planing and rabbet cutting. Attach the edge guide to either side of the planer for planing edges and attach the edge guide to the left side for making rabbet cuts.
Page 13 MAINTENANCE W ARNING: When servicing, use only identical Ryobi replacement parts. Use of any other part may create a hazard or cause product damage. GENERAL All par ts represent an impor tant par t of the double insulation system and should be serviced only at an authorized ser vice center .
Page 14 MAINTENANCE REPLACING BLADES See Figures 13, 14 and 15. The blades in y our planer are rev ersible. Therefore , you can reverse the blades when one edge becomes dull. Always replace or reverse blades in pairs. Do not attempt to sharpen blades.
Page 15 Fig. 16 Fig. 17 REPLACING THE BELT See Figures 16 and 17. When replacing the belt, use the recommended replace- ment belt only , Ry obi par t number 5695001 . 1. Unplug the planer . W ARNING: Failure to unplug the planer could result in accidental starting causing serious injury.
OPERA T OR'S MANU AL P ower Planer Model No. HPL51 DOUBLE INSULA TED R Y OBI TECHNOLOGIES INC. 1428 P ear man Dairy Road Anderson, SC 29625 P ost Office Box 1207 Anderson, SC 29622 www .
デバイスRyobi HPL51の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Ryobi HPL51をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはRyobi HPL51の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Ryobi HPL51の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Ryobi HPL51で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Ryobi HPL51を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はRyobi HPL51の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Ryobi HPL51に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちRyobi HPL51デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
