Ryobi OutdoorメーカーCS1800の使用説明書/サービス説明書
ページ先へ移動 of 34
Your new cordless chain saw has been engineered and manufactured to Ryobi's high standard for dependability, ease of operation, and operator safety.
2 ■ T able of Contents / Introduction ............................................................................................... .......................... 2 ■ Important Safety Instructions ....................................................
3 READ ALL INSTRUCTIONS BASIC SAFETY PRECAUTIONS ■ Do not operate a chain saw with one hand! Use a firm grip with thumbs and fingers encircling the chain saw handles. Serious injury to the operator, helpers, bystanders, or any combination of these persons may result from one-handed operation.
4 KICKBACK See Figures 1 and 2. ■ WARNING: Kickback may occur when the moving chain contacts an object at the upper portion of the tip of the guide bar or when the wood closes in and pinches the saw chain in the cut.
5 IMPORT ANT SAFETY INSTRUCTIONS PULL PUSH Fig. 3 ■ Push and Pull - This reaction force is always opposite to the direction the chain is moving where wood contact is made. Thus, the operator must be ready to control the PULL when cutting on the bottom edge of the bar, and PUSH when cutting along the top edge.
6 UNDERSTANDING YOUR CHAIN SAW SAFETY DEVICES See Figure 4. SAFE-T-TIP® Anti-Kickback Nose Guard The SAFE-T -TIP® prevents kickback from happening, because it covers the tip of the bar where kickback is generated. Never attempt any kind of cutting where the SAFE-T -TIP® would have to be removed from the bar tip.
7 b. That extension cord is properly wired and in good electrical condition; and c. That wire size is large enough for AC ampere rating of charger as specified below: Cord Length (Feet) 25' 50' 100' Cord Size (AWG) 16 16 16 NOTE: AWG = American Wire Gage ■ Do not operate charger with a damaged cord or plug.
8 Important: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer.
9 Important: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. SYMBOL NAME EXPLANATION SAFE-T-TIP The SAFE-T-TIP® nose guard on your bar nose prevents rotational kickback.
10 Motor 18 V olt, DC Bar Length 10 in. (254 mm) Replacement Bar Part No. 671256002 or 671667002 Replacement Chain Part No. 6958301 or 690583002 Net Weight 7.
11 Fig. 5 CHAIN OIL T ANK CAP REAR HANDLE FRONT HANDLE BAR CHAIN SAFE-T -TIP® BA TTERY P ACK HEX KEY HEX KEY STORAGE AREA HAND GUARD TRIGGER LOCK BUTTON TRIGGER FEA TURES SCABBARD.
12 GLOSSAR Y OF TERMS Front Handle The support handle located at or toward the front of the chain saw . Front Handle Guard A structural barrier between the front handle of a chain saw and the guide bar , typically located close to the hand position on the front handle and sometimes employed as an activating lever for a chain brake.
13 BATTERY PACK AND CHARGER LED FUNCTION OF CHARGER See Figure 6. LED WILL BE ON T O INDICA TE ST A TUS OF CHARGER AND BA TTERY P ACK: ■ Red LED on = Fast charging mode. ■ Green LED on = Fully charged battery pack. ■ Y ellow and Green LEDs on = Control charge or defective battery pack.
14 TO INSTALL BATTERY PACK See Figure 7 . 1. Place the battery pack in your chain saw. Align raised rib on battery pack with groove in chain saw’s battery port. 2. Make sure the latches on each side of the battery pack snap in place and that battery pack is secured in chain saw before beginning operation.
15 Fig. 9 TRIGGER LOCK BUTTON TRIGGER W ARNING: Keep body to the left of the chain line. Never straddle the saw or chain, or lean over past the chain line. STARTING THE CHAIN SAW 1. Place the chain saw on a flat bare surface and make sure no objects or obstructions are in imme- diate vicinity which could come in contact with the bar and chain.
16 3. Maintain a proper grip on the saw whenever the unit is running. The fingers should encircle the handle and the thumb is wrapped under the handle- bar.
17 Fig. 13 PROPER CUTTING STANCE See Figure 13. ■ Weight should be balanced with both feet on solid ground. ■ Keep left arm with elbow locked in a "straight arm" position to withstand any kickback force. ■ Your body should always be to the left of the chain line.
18 W ARNING: If the tree starts to fall in the wrong direction, or if the saw gets caught or hung up during the fall, leave the saw and save yourself! ■ Felling a tree - When bucking and felling ope.
19 ■ Felling Backcut. The backcut is always made level and horizontal, and at a minimum of 2 inches (5 cm) above the horizontal cut of the notch. See Figures 15 and 16. ■ Never cut through to the notch. Always leave a band of wood between the notch and backcut (approximately 2 inches (5 cm) or 1/10 the diameter of the tree).
20 LOAD FINISHING CUT 1ST CUT 1/3 DIA LOG SUPPORTED A T ONE END: LOG SUPPORTED A T BOTH ENDS: FINISHING CUT 1ST CUT 1/3 DIA LOAD Fig. 20 OPERA TION BUCKING LOGS UNDER STRESS See Figures 20 and 21. When the log is supported along its entire length, it should be cut from the top or overbucking.
21 TYPES OF CUTTING USED See Figure 21. OVERBUCKING Begin on the top side of the log with the bottom of the saw against the log; exert light pressure downward. Note that the saw will tend to pull away from you. UNDERBUCKING Begin on the under side of the log with the top of the saw against the log; exert light pressure upward.
22 PRUNING See Figure 23. Pruning is trimming limbs from a live tree. ■ Work slowly, keeping both hands on the chain saw with a firm grip. Always make sure your footing is secure and your weight is distributed evenly on both feet. ■ Do not cut from a ladder, this is extremely danger- ous.
23 ASSEMBLING BAR AND CHAIN See Figures 25, 26, 27, 28 and 29. W ARNING: The safety instructions in this section are to protect the user from serious personal injury. CAUTION: Remove the battery pack from the chain saw and make sure the chain has stopped before you do any work on the saw.
24 Fig. 27 CHAIN TENSIONING SCREW 7. Replace the chain cover, washer and chain cover screw. Tighten the chain cover screw finger tight only. The bar must be free to move for tension adjustment.
25 CHAIN TENSION See Figures 30 and 31. 1. Stop the engine before setting the chain tension. Make sure the guide bar screw is loosened to finger tight, turn the chain tensioner clockwise to tension the chain. Refer to “Assembling the Bar and Chain” earlier in this manual for additional information.
26 CHAIN MAINTENANCE See Figures 32 and 33. Fig. 34 Fig. 33 CHECK FOR WEAR OR DAMAGE Use only low-kickback chain on this saw . This fast- cutting chain will provide kickback reduction when properly maintained. For smooth and fast cutting, chain needs to be main- tained properly .
27 W ARNING: Improper chain sharpening increases the potential of kickback. 5. Put a few firm strokes on every tooth. File all left hand cutters in one direction. Then move to the other side and file the right hand cutters in the opposite direction. Occasionally remove filings from the file with a wire brush.
28 Use a Flat File and a Depth Gauge Jointer to lower all gauges uniformly . Depth gauge jointers are available in .020 in. to .035 in. (0.5 mm to 0.9 mm). Use a .025 in. (0.6 mm) depth gauge jointer . After lowering each depth gauge, restore original shape by rounding the front.
29 SAFE-T-TIP® NOSE GUARD MAINTE- NANCE See Figures 42 and 43. T ighten the mounting screw of the nose guard as instructed below . These are specially hardened screws. If the screw cannot be installed tightly , replace both the screw and the SAFE-T -TIP® before further operation.
30 BATTERIES The battery pack for your chain saw is equipped with nickel-cadmium rechargeable batteries. Length of service from each charging will depend on the type of work you are doing. The batteries in this tool have been designed to provide maximum trouble free life.
31 RECOMMENDED BAR AND CHAIN COMBINATIONS Bar Part Number - 10 in. (254 mm) 671256002 or 671667002 Chain Part Number 6958301 or 690583002 BAR AND CHAIN COMBINA TIONS PROBLEM POSSIBLE CAUSE SOLUTION IF THESE SOLUTIONS DO NOT SOL VE THE PROBLEM CONT ACT YOUR AUTHORIZED SERVICE DEALER.
32 NOTES.
33 NOTES.
983000-353 10-04 R YOBI TECHNOLOGIES INC. 1428 Pearman Dairy Road Anderson, SC 29625 Post Office Box 1207 Anderson, SC 29622 www .ryobitools.com 1-800-525-2579 CUSTOMER SER VICE INFORMA TION For parts or service, contact your nearest Ryobi authorized service center.
デバイスRyobi Outdoor CS1800の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Ryobi Outdoor CS1800をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはRyobi Outdoor CS1800の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Ryobi Outdoor CS1800の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Ryobi Outdoor CS1800で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Ryobi Outdoor CS1800を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はRyobi Outdoor CS1800の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Ryobi Outdoor CS1800に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちRyobi Outdoor CS1800デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
