SamsungメーカーBixolon SRP-350の使用説明書/サービス説明書
ページ先へ移動 of 21
User ’ s Manual SRP-350 Thermal Printer Rev . 1.01 http://www .samsungminiprinters.com.
Rev . 1.01 - 2 - SRP-350 ■ Safety Precautions In using the present appliance, please keep t he following safety regulations in order to prevent any hazard or material damage. W ARNING Violating following instructions c an cause serious injury or death.
Rev . 1.01 - 3 - SRP-350 CAUTION Violating f ollowi ng instruct ions can cause slight wo und or damage t he appliance. If you observe a stra nge smoke, odor or noise from the printer , unplug it before t aking following measures. • Switch off the printer and unplug the set from the mains.
Rev . 1.01 - 4 - SRP-350 ■ W arning - U.S.A This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rule s. These limits are designed to provide reasonable protection against harmful interfer ence when the equipment is operated in a commercial environment.
Rev . 1.01 - 5 - SRP-350 ■ Introduction The SRP-350 Roll Printer are designed for use with electronic instruments such as system ECR, POS, banking equipment, com puter peripheral equipment, etc. The main features of the printer are as follows: 1. High speed printing : 35.
Rev . 1.01 - 6 - SRP-350 ■ T able of Content s 1. Setting Up the Printer ................................................................................................... 7 1-1 Unpacking ............................................................
Rev . 1.01 - 7 - SRP-350 1. Setting Up the Printer 1- 1 Unpacking Y our printer box should include these items. If any items are damaged or missing, pleas e contact your dealer for assist ance.
Rev . 1.01 - 8 - SRP-350 1-2 Connecting the Cables Y ou can connect up the three cables to the printe r . They all connect to the connector p anel on the back of the printer , which is shown below: ※ NOTE Before connecting any of the cables, make sure that both the printer and the host are turned off.
Rev . 1.01 - 9 - SRP-350 1-2-2 Serial Interface (RS-485) ON IF A -SF TYPE Drawer k ick-out connecto r Power supply connecto r Interface connector ※ When the Dip Switch is “ON” on the Serial Interface Board, DTR and RTS are connected each other .
Rev . 1.01 - 10 - SRP-350 1-2-3 Parallel Interface (IEEE1284) IF A -P TYPE Drawer k ick-out connecto r Power supply connecto r Interface connector Pin No.
Rev . 1.01 - 1 1 - SRP-350 1-2-4 USB Interface USB IF A -U TYPE Drawer k ick-out connecto r Power supply connector USB connec tor Pin No. Signal Name Assignment (Color) Function Shell Shield Drain Wir.
Rev . 1.01 - 12 - SRP-350 1-4 Setting the Dip Switches 1-4-1 Serial Interface SW Function ON OFF Default 1 Auto Line Feed Always enabled Always dis abled OFF 2 Reserved - - OFF 3 Handshaking XON/OFF D.
Rev . 1.01 - 13 - SRP-350 1-4-2 Parallel & USB Interface SW Function ON OFF Default 1 Auto Line Feed Always enabled Always disabled OFF 2 Reserved - - OFF 3 Reserved - - OFF 4 Reserved - - OFF 5 R.
Rev . 1.01 - 14 - SRP-350 1-5 Installing or Replacing the Paper Roll ※ NOTE Be sure to use paper rolls that meet the spec ifications. Do not use p aper rolls that have the paper glued to the core because the pr inter cannot detect the p aper end correctly .
Rev . 1.01 - 15 - SRP-350 1-5-5 Be sure to note the correct direct ion that the paper comes of f the roll. 1-5-6 Pull out a small amount of paper , as shown. Then close the cover . ※ NOTE When closing the cover , press the center of printer cover firmly to prevent paper miss-loading.
Rev . 1.01 - 16 - SRP-350 1-6 Adjustments and Settings The SRP-350 is set up at the factory to be appropriate for almost all users. It does, however , offer some settings for users with special requirement s. It has DIP switches that allow you to change communication settings, such as handshaking and parity check, as well as print density .
Rev . 1.01 - 17 - SRP-350 1-8 Connecting the computer Y ou need an appropriate interface cable. 1-8-1 Plug the cable connector securely in to the printer ’s interface connector . 1-8-2 T ighten the screws on both si des of the cable connector . 1-8-3 Attach the ot her end of the cable to the computer .
Rev . 1.01 - 18 - SRP-350 2. Self Test The self-test checks whether the printer has any problems. If the printe r does not function properly , contact your dealer . The self-test checks the following; 2-1 Make sure paper roll has been inst alled properly .
Rev . 1.01 - 19 - SRP-350 3. Hexadecimal Dumping This feature allows experienced users to see exactly what data is coming to the printer . This can be useful in finding software problem s.
Rev . 1.01 - 20 - SRP-350 4. Specification Printing method Thermal line printing Dot density 180 X 180 dpi (7dot s/mm) Printing width 72.192 ± 0.2mm Paper width 79 ~ 80 mm Characters per line (default) 42 (Font A) 56 (Font B) Printing speed 35.
Rev . 1.01 - 21 - SRP-350 5. Appendix 5-1 Cleaning Printer Paper dust inside the printer may lower the print quality . In this case clean the printer as follows. 5-1-1 Open the printer cover and remove the paper if exist s. 5-1-2 Clean the print head with a cott on swab moistened with alcohol solvent.
デバイスSamsung Bixolon SRP-350の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Samsung Bixolon SRP-350をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSamsung Bixolon SRP-350の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Samsung Bixolon SRP-350の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Samsung Bixolon SRP-350で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Samsung Bixolon SRP-350を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSamsung Bixolon SRP-350の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Samsung Bixolon SRP-350に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSamsung Bixolon SRP-350デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
