SamsungメーカーHPL5025の使用説明書/サービス説明書
ページ先へ移動 of 36
IMPORTER Samsung Electronics Mexico S.A. de C.V . Saturno No. 44, Col Nueva Industrial V allejo Gustavo A. Madero C.P . 07700, Mexico TEL) 52-5-747-5100 EXPORTER Samsung Electronics co.
Thank you for choosing Samsung! Y our new Samsung product represents the latest in television technol- ogy . W e designed it with easy-to-use on-screen menus and closed captioning capabilities, making it one of the best products in its class.
User Instructions The Federal Communications Commission Radio Frequency Interference Statement includes the fol- lowing warning: NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Setup Y our New Plasma Display Panel ........................10 Remote Control Buttons ....................................12 W all Installation Instructions ..............................14 T urning the PDP On and Off..............................18 Connection (Connecting Speakers / Receiver) Connecting Speakers .
PLASMA DISPLA Y PANEL Setup Y our New Plasma Display Panel ....................................................10 Remote Control Buttons ................................................................12 W all Installation Instructions ...............
Remote Control Signal Receiver Aim the remote control towards this spot on the Monitor . POWER Press to turn the PDP on and off. SOURCE , MENU, VOLUME (-,+), SELECT ( ▼ , ▲ ), MUTE Front Panel 11 .
ı VCR control buttons Controls VCR tape functions: Stop, Rewind, Play/Pause, Fast For ward. ˜ SET button Use during setting up of this remote control, so that it will work compatibly with other devices (VCR, cable box, DVD, etc.) ¯ Clock set button Press to clock setting.
1 See the drawing of the wall attachment panel shown in page 14 to check for the stability of the wall where the PDP is to be installed. If the wall is not enough strong to support the PDP , strengthen the wall before installation.
Remove the fixing bolts from both sides (left and right) of the wall attachment panel. Lift and pull the bottom of the display a small amount, to separate the insulation holder point from the bottom of the wall attachment panel. Lift the display and separate the insulation holder point from the groove on top of the wall attachment panel.
Displaying Status Information Press the Display button on the remote control. The PDP will display the Screen size, Resolution, Current time, and screen mode. Displaying Clock Press the Clock Display button on the remote control. The Current time will be displayed on the screen.
PLASMA DISPLA Y PANEL Connection (Connecting Speakers / Receiver) Connecting Speakers ....................................................................22 Connecting a VCR/Cable Box ......................................................23 Connecting a DVD/Set-T op Box .
23 Connecting Speakers 22 Speaker Audio Cable Connect the speaker audio cable to the external speaker output jack on the rear of the PDP matching the “+” and “-” ends of the cable with the diagram on the PDP . How to Connect Fix the bracket onto the guide pole located on the rear of speaker and fasten the screws.
PLASMA DISPLA Y PANEL Picture Contr ol Customizing the Picture ................................................................26 Using Automatic Picture Settings ....................................................27 Viewing the Picture-in-Picture ..
Customizing the Picture Y ou can use the on-screen menus to change the Brightness, Contrast, Sharpness, Color , and Tint settings of your PDP . 27 1 Press the Menu button, then press the joystick to enter . 2 Move the joystick left or right to select the “Custom”, “Standard”, or “Mild” picture setting.
V iewing the Picture-in-Picture 29 Selecting an External Signal Y ou can use PIP to view a signal from an external source, such as a VCR. 1 Press the Menu button. Move the joystick up or down to select the “PIP”, then press the joystick to enter .
31 Wide Sets the picture to 16:9 wide mode. Panorama Use this mode for the wide aspect ratio of a panoramic picture. Zoom1 Magnify the size of the picture vertically on screen. Zoom2 Magnify the size of the picture more than Zoom1. Stretch Moves the Zoom2 picture up a little to fully show the bottom.
Freezing the Picture 32 Still Press the Still button on the remote control to freeze a mov- ing picture into a still one. Press again to cancel. PLASMA DISPLA Y PANEL Sound Contr ol Customizing the Sound ...............................................
35 Customizing the Sound 34 1 Press the Menu button. Move the joystick up or down to select the “ AUDIO ” , then press the joystick to enter . 2 Move the joystick left or right to select the “ Custom ” , “ Standard ” , “ Music ” , “ Movie ” or “ Speech ” sound setting.
PLASMA DISPLA Y PANEL Time Setting Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 Setting the Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39 Setting the Timers . . . . . .
Setting the Clock 39 Y ou can set your PDP to automatically turn off after a preset inter val. 1 Press the Menu button. Move the joystick up or down to select “ TIME ” , then press the joystick to enter . 2 Move the joystick up or down to select the “ Sleep ” , then move the joystick left or right.
Setting the Timers 41 6 Move the joystick up or down to select “ Off ” , then move the joystick left or right to select “ On ” . 7 If you want to set the Off T ime, move the joystick down to select the “ Off Time ” . Set the “ Off Time ” just as you set the “ On T ime ” .
PLASMA DISPLA Y PANEL Connecting PC and Operation Connecting to a PC ......................................................................44 Adjusting the PC Screen ................................................................48 Changing the Position of the Image .
Pin Configuration • 15Pin Signal Cable (based on protruded pin) Setting up Y our Monitor Plug and Play Our adoption of the new VESA Plug and Play solution eliminates complicated and time consuming setup. It allows you to install your monitor in a Plug and Play compatible system without the usual hassles and confusion.
47 46 How to Set up Y our Display Setting (Windows only) Notes: The plasma panel of this monitor is composed 1366 pixels & 768 lines. That is, the best resolution of this monitor is 1366 X 768.
49 After connecting the PDP to your PC, adjust the position of screen if it is not well-aligned. Preset: • Press the RGB button to select the PC mode. 1 Press the Menu button. Move the joystick up or down to select the “ SETUP ” , then press the joystick to enter .
51 Preset: • Press the RGB button to select the PC mode. 1 Press the Menu button. Move the joystick up or down to select the SETUP , then press the joystick to enter . 2 Move the joystick up or down to select the “ Zoom/Panning ” , then move the joystick left or right to enter .
53 Picture Automatic Adjustment On/Off Preset: • Press the RGB button to select the PC mode. 1 Press the Menu button. Move the joystick up or down to select the SETUP , then press the joystick to enter . 2 Move the joystick up or down to select the “ Image Lock ” , then move the joystick left or right to enter .
55 Fine T uning (Phase) Preset: • Press the RGB button to select the PC mode. 1 Press the Menu button. Move the joystick up or down to select the SETUP , then press the joystick to enter . 2 Move the joystick up or down to select the “ Image Lock ” , then move the joystick left or right to enter .
57 56 Preset: • Press the RGB button to select the PC mode. 1 Press the Menu button. Move the joystick up or down to select the SETUP , then press the joystick to enter . 2 Move the joystick up or down to select the “ Miscel- laneous ” , then move the joystick left or right to enter .
Selecting a Menu Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 Setting the Multi Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61 Using the Key Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting a Menu Language 61 60 Setting the Multi Contr ol 1 Press the Menu button. Move the joystick up or down to select the “SETUP”, then press the joystick to enter . 2 Move the joystick left or right to select the appropri- ate language: English, Spanish, or French.
This PDP's remote control can operate almost any VCR, cable box, or DVD. After it has been set up properly , your remote control can operate in four different modes: VCR, Cable, or DVD. Pressing the corresponding button on the remote control allows you to switch between these modes, and control whichever piece of equipment you choose.
PLASMA DISPLA Y PANEL Appendix T roubleshooting ............................................................................66 Care and Maintenance ................................................................67 Specifications .....................
67 66 T r oubleshooting Problem Poor picture. The power indicator is amber blinking. Y our Remote control does not operate the monitor . The monitor won ’ t turn on. There is no screen image. The image is too light or too dark. The image is too large or too small.
69 68 Specifications Exterior design and product specifications are subject to change without prior notice to improve the performance of this product. This PDP applies to Class B digital device.
Memo 71 70 Memo.
デバイスSamsung HPL5025の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Samsung HPL5025をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSamsung HPL5025の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Samsung HPL5025の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Samsung HPL5025で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Samsung HPL5025を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSamsung HPL5025の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Samsung HPL5025に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSamsung HPL5025デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
