SamsungメーカーHPN4239の使用説明書/サービス説明書
ページ先へ移動 of 52
BN68-00566A-02 Owner’ s Instructions HPN4239 1-800-SAMSUNG (1-800-726-7864) Samsung Electronics America Service Division 400 V alley Road, Suite 201 Mount Arlington, NJ 07856 www .samsungusa.com Samsung Electronics Canada Inc. Samsung Customer Care 7037 Financial Drive Mississauga, Ontario L5N 6R3 www .
Wa rning! Impor tant Safety Instructions 2 CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE P ARTS INSIDE. REFER SER VICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates high voltage is present inside.
•P rotect the power cord. Power supply cords should be routed so that they won’t be walked on or pinched by objects placed on or against them. Pay particular attention to cords at plugs, convenience recepta- cles, and the point where they exit from the unit.
Impor tant W arranty Information Regarding T elevision Format V iewing User Instructions W ide screen format PDP Displays (16:9,the aspect ratio of the screen width to height) are primarily designed to view wide screen format full-motion video.
PLASMA DISPLA Y PANEL General Information Y our New Plasma Display Panel ....................................................10 Remote Control Buttons ................................................................12 W all Installation Instructions .
Front Panel Y our New Plasma Display Panel 10 11 Rear Panel Œ Service jack For ser vice only . ´ DVI Input jacks Receives the digital video/audio signals from a set top box or PC. ˇ PC(RGB) Input jacks(15pin) Connect to the video/audio output jacks on your PC.
¸ SURROUND button Press the hear the Dolby surround effect. ˛ MTS button Press to choose stereo, mono or Separate Audio Pro- gram (SAP broadcast). ◊ AUTO PROG. button The TV automatically cycles through all of the avail- able channels and stores them in memor y .
1 Remove the screws on the rear of the PDP panel. 2 Connect Insulation holders to screws. (see the illustration below) 3 T ighten the screws connected to the Insulation holders on the rear of the PDP panel. Wa ll Installation Instructions 1 Do not install the PDP in any location other than a vertical wall.
16 17 4 Put the 4 pegs on the PDP in the grooves of the wall mount bracket and pull down on the PDP ( Œ ) to secure it to the wall mount bracket. ( ´ ) Tighten the screws as shown ( ˇ ) so that the PDP cannot be separated from wall mount bracket. 1.
PLASMA DISPLA Y PANEL Connections Connecting VHF and UHF Antennas ..............................................20 Connecting Cable TV ....................................................................21 Connecting Speakers..........................
21 Connecting VHF and UHF Antennas Connecting Cable TV Y ou can connect different cable systems to your PDP , including cable without a cable box, and cable with a cable box that descrambles some or all channels. 20 Antennas with 75-ohm Round Leads If your antenna looks like this: it has 75-ohm round leads.
22 23 Connecting Speakers External speakers are sold seperately . Check with your dealer . Connect the speaker audio cable to the external speaker output jack on the PDP matching the “+” and “-” ends of the cable with the diagram on the PDP .
25 Connecting a Camcorder 24 Connecting a VCR to the Video or S-Video/Audio jack S-Video Cable Audio Cable V ideo Cable Power Plug Connect the Video/Audio cables between the AUDIO(L/R)/VIDEO jacks on the PDP and AUDIO/VIDEO OUT jacks on the VCR. (Note: For better video, you can use an S-Video cable.
27 Connecting a DVD Player (480i, 480p) This PDP displays the optimum picture in 720p mode. 26 Playing DVD Audio Cable V ideo Cable Power Plug Connect a Video Cable between the Y , Pb, Pr (COMPONENT1, 2) input jacks on the PDP and Y/P B /P R output jacks on the DVD player .
PLASMA DISPLA Y PANEL Operation Tu rn ing the PDP On and Off ..........................................................30 Memorizing the Channels..............................................................32 Setting Up Y our Remote Control .........
Tu rning the PDP On and Off 30 31 Tu rning the PDP On and Off Press the POWER button on the remote control. The PDP will be turned on and you will be ready to use its features.
Selecting the Video Signal-source Before your television can begin memorizing the available channels, you must specify the type of signal source that is connected to the PDP (i.e., an antenna or a cable system). 1 Press the MENU button. Press the ▲ or ▼ button to select “Channel”, then press the ENTER button.
To View Memorized Channel (PIP Mode) 1 Press the MENU button. Press the ▲ or ▼ button to select “Channel”, then press the ENTER button. 2 Press the ▲ or ▼ button to select “Ch. Scan”, then press the ENTER button. Only the memorized channels are chosen.
36 37 Setting Up Y our Remote Contr ol This PDP's remote control can operate almost any VCR, cable box or DVD. After it has been set up properly , your remote control can operate in four different modes :TV , VCR, Cable or DVD.
Setting the Signal Source 1 Press the MENU button. Press the ENTER button to select “Input”. 2 Press the ENTER button to select “Source”. 3 Press the ▲ or ▼ button to select signal source, then press the ENTER button.
40 PLASMA DISPLA Y PANEL Picture Contr ol Customizing the Picture ................................................................42 Using Automatic Picture Settings ....................................................43 Selecting the Color T one ....
Customizing the Picture Y ou can use the on-screen menus to change the Contrast, Brightness, Sharpness, Color , and T int settings of your PDP . 43 1 Press the MENU button. Press the ▲ or ▼ button to select “Picture”, then press the ENTER button.
44 Selecting the Color T one 1 Press the MENU button. Press the ▲ or ▼ button to select “Picture”, then press the ENTER button. 2 Press the ▲ or ▼ button to select “Color T one”, then press the ENTER button. 3 Press the ▲ or ▼ button to select “Cool2”, “Cool1”, “Normal”, “W arm1” or “W ar m2”.
47 46 Freezing the Picture Still Press the STILL button on the remote control to freeze a moving picture. Press again to cancel. Changing the Screen Size W W ide ide Sets the picture to 16:9 wide mode. Panorama Converts regular 4:3 aspect ratio screen to wide screen.
48 Selecting an External Signal Y ou can use PIP to view a signal from an external source, such as a VCR. 1 Press the MENU button. Press the ▲ or ▼ button to select “Picture”, then press the ENTER button. 2 Press the ▲ or ▼ button to select “PIP”, then press the ENTER button.
50 Changing the Size of the PIP Window 1 Press the MENU button. Press the ▲ or ▼ button to select “Picture”, then press the ENTER button. 2 Press the ▲ or ▼ button to select “PIP”, then press the ENTER button. 3 Press the ▲ or ▼ button to select “Size”, then press the ENTER button.
Changing the Location of the PIP Image 1 Press the MENU button. Press the ▲ or ▼ button to select “Picture”, then press the ENTER button. 2 Press the ▲ or ▼ button to select “PIP”, then press the ENTER button. 3 Press the ▲ or ▼ button to select “Position”, then press the ENTER button.
54 PLASMA DISPLA Y PANEL Sound Contr ol Customizing the Sound ................................................................56 Using Automatic Sound Settings ....................................................57 Choosing a Multi-Channel Sound (MTS)Soundtrack .
57 56 1 Press the MENU button. Press the ▲ or ▼ button to select “Sound”, then press the ENTER button. 2 Press the ENTER button to select “Mode”. 3 Press the ▲ or ▼ button to select “Standard”, “Music”, “Movie”, “Speech” or “Custom” sound setting, then press the ENTER button.
59 58 1 Press the MENU button. Press the ▲ or ▼ button to select “Sound”, then press the ENTER button. 2 Press the ▲ or ▼ button to select “Auto V olume”, then press the ENTER button. 3 Press the ▲ or ▼ button to select “On”, then press the ENTER button.
1 Press the MENU button. Press the ▲ or ▼ button to select “Sound”, then press the ENTER button. 2 Press the ▲ or ▼ button to select “Sub W oofer”, then press the ENTER button. 3 Press the ENTER button to select “Sub W oofer”. Press the ▲ or ▼ button to select “On”, then press the ENTER button.
PLASMA DISPLA Y PANEL Channel Contr ol Fine T uning Channels ....................................................................64 LNA (Low Noise Amplifier) .
65 Fine T uning Channels Use fine tuning to manually adjust a particular channel for optimal reception. 64 1 Press the MENU button. Press the ▲ or ▼ button to select “Channel”, then press the ENTER button. 2 Press the ▲ or ▼ button to select “Fine Tune”, then press the ENTER button.
PLASMA DISPLA Y PANEL Connecting a PC and Operation Connecting to a PC ......................................................................68 Adjusting the PC Screen ................................................................72 Changing the Position of the Image .
69 Connecting to a PC Connection to a Macintosh computer may require in adapter . 68 To watch the PC screen: 1. T urn on your PDP 2. Press the TV/VIDEO button on the remote control or SOURCE button on the front panel to select “PC”. 3. T urn on PC and check for PC system requirements.
70 71 How to Set up Y our PC Software (Windows only) The Windows display-settings for a typical computer are shown below . However , the actual screens on your PC will probably be different, depending upon your particular version of Windows and your particular video card.
73 Adjusting the PC Screen 72 Adjusting the R.G.B Preset: •P ress the TV/VIDEO button to select “PC”. 1 Press the MENU button. Press the ▲ or ▼ button to select “Picture”, then press the ENTER button. 2 Press the ▲ or ▼ button to select “Color Control”, then press the ENTER button.
74 75 Picture Quality Adjustment Picture Automatic Adjustment Preset: •P ress the TV/VIDEO button to select “PC”. 1 Press the MENU button. Press the ▲ or ▼ button to select “Setup”, then press the ENTER button. 2 Press the ▲ or ▼ button to select “PC”, then press the ENTER button.
76 77 Information Preset: •P ress the TV/VIDEO button to select “PC”. 1 Press the MENU button. Press the ▲ or ▼ button to select “Setup”, then press the ENTER button. 2 Press the ▲ or ▼ button to select “PC”, then press the ENTER button.
PLASMA DISPLA Y PANEL Time Setting Setting the Clock .......................................................................80 Setting the Sleep Timer...............................................................81 Setting the Timers ................
Setting the Clock Y ou can set your PDP to automatically turn off after a preset interval. 1 Press the MENU button. Press the ▲ or ▼ button to select “Setup”, then press the ENTER button. 2 Press the ▲ or ▼ button to select “Time”, then press the ENTER button.
6 Press the √ button to select “Channel”, then press the ▲ or ▼ button to select the channel you want when PDP turns on. 7 Press the √ button to select “V ol.”, then press the ▲ or ▼ button to select the volume level you want when PDP turns on.
Selecting a Menu Language .....................................................86 Vi ewing Closed Captions .........................................................87 Digital Noise Reduction ...........................................................88 Setting Auto Power Off .
Selecting a Menu Language 86 87 1 Press the MENU button. Press the ▲ or ▼ button to select “Setup”, then press the ENTER button. Press the ▲ or ▼ button to select “Caption”, then press the ENTER button. 2 Press the ENTER button to select “Caption”.
1 Press the MENU button. Press the ▲ or ▼ button to select “Setup”, then press the ENTER button. 2 Press the ▲ or ▼ button to select “Auto Power Off”, then press the ENTER button. 3 Press the ▲ or ▼ button to select “On” or “Off”, then press the ENTER button.
90 Using the V -Chip The V -Chip feature automatically locks out programs that are deemed inappropriate for children. The user must enter a PIN (personal ID number) before any of the V -Chip restrictions are set up or changed. Note: When the V -chip feature is activated, the PIP and auto channel program features do not function.
92 How to Set up Restrictions using the “TV guidelines” First, set up a personal identification number (PIN), and enable the V -Chip. (See previous section.) Parental restrictions can be set up using either of two methods: The TV guidelines or the MP AA rating.
94 95 How to Set up Restrictions using the MP AA Ratings: G, PG, PG-13, R, NC-17, X The MP AA rating system uses the Motion Picture Association of America (MP AA) system, and its main application is for movies.
96 PLASMA DISPLA Y PANEL Appendix Tr oubleshooting............................................................................98 Care and Maintenance ................................................................99 Specifications ...................
98 99 Tr oubleshooting Problem Poor picture. Y our Remote control does not operate the PDP . The PDP won’t turn on. There is no screen image. The image is too light or too dark. The image is too large or too small. Before you call a ser vice technician, please scan this list of problems and possible solutions.
100 101 Memo Specifications HPN4239 1027 (W) X 79 (D) X 630.5 (H) mm ; 40.43 (W) X 3.11 (D) X 24.82(H) inches 58 (W) X 21 (D) X 210 (H) mm ; 2.28 (W) X 0.
103 Memo Memo 102.
デバイスSamsung HPN4239の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Samsung HPN4239をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSamsung HPN4239の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Samsung HPN4239の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Samsung HPN4239で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Samsung HPN4239を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSamsung HPN4239の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Samsung HPN4239に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSamsung HPN4239デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
