SamsungメーカーPS50A550の使用説明書/サービス説明書
ページ先へ移動 of 51
Plasma TV user manual BN68-01447A-00 Contact SAMSUNG WORLD-WIDE If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care centre. Country Customer Care Centre Web Site AUSTRALIA 1300 362 603 www .
English - 2 © 2008 Samsung Electronics Co., Ltd. All rights reserved. User Instructions Screen Image retention Do not display a still image (such as on a video game or when hooking up a PC to this PDP) on the plasma monitor panel for more than 2 hours as it can cause screen image retention.
English - 3 Symbols ☛ ➢ Press Important Note Contents General Information User Instructions ............................................. 2 Checking Parts ................................................ 4 Using the Stand-Base ........
English - 4 Using the Stand-Base ➢ T wo or more people should carry the PDP . Never lay the PDP on the floor because of possible damage to the screen. Always keep the PDP upright. The PDP can rotate 20 degrees in right and left directions.
English - 5 Control Panel 1 SOURCE T oggles between all the available input sources ( TV , A V1 , A V2 , S-Video , Component1 , Component2 , PC , HDMI1 , HDMI2 , HDMI3 ). ➢ In the on-screen menu, use this button as you would use the ENTER button on the remote control.
English - 6 Continued... Side Panel ➢ The product colour and shape may vary depending on the model. Connection Panel ☛ Whenever you connect an audio or video system to your set, ensure that all elements are switched off. When connecting an external device, match the colour of the connection terminal to the cable.
English - 7 1 ANT IN 75Ω Coaxial connector for Aerial/Cable Network. 2 SERVICE − Connector for service. − Connect the serial jack between the electro-motion wall mount bracket and your TV when you want to adjust the TV viewing angle using your remote control.
English - 8 V iewing the Remote Control 1 POWER button (turns the TV on and of f) 2 Selects the TV mode directly 3 Number buttons for direct channel access 4 One/T wo-digit channel selection 5 T empor.
English - 9 Installing Batteries in the Remote Control 1 Lift the cover at the back of the remote control upward as shown in the figure. 2 Install two AAA size batteries. ➢ Make sure to match the “ + ” and “ – ” ends of the batteries with the diagram inside the compartment.
English - 10 Plug & Play Feature When the television is initially powered on, several basic customer settings proceed automatically and subsequently . The following settings are available. 1 If the television is in standby mode, press the POWER button on the remote control.
English - 11 If you want to reset this feature … 1 Press the MENU button to display the menu. 2 P r e s s t h e ▲ o r ▼ b u t t o n t o s e l e c t S e t u p , t h e n p r e s s t h e ENTER button. 3 P r e s s t h e ENTER b u t t o n a g a i n t o s e l e c t Plug & Play .
English - 12 V iewing External Signal Sources Y ou can switch between viewing signals from connected equipment, such as a VCR, DVD, Set-T op Box, and the TV source (broadcast or cable). 1 Press the MENU button to display the menu. 2 Press the ▲ or ▼ button to select Input , then press the ENTER button.
English - 13 Storing Channels Automatically Y ou can scan for the frequency ranges available to you (availability depends on your country). Automatically allocated programme numbers may not correspond to actual or desired programme numbers. However you can sort numbers manually and clear any channels you do not wish to watch.
English - 14 Adding / Locking Channels Using the Channel Manager , you can conveniently add or lock channels. 1 Press the MENU button to display the menu. 2 Press the ▲ or ▼ button to select Channel , then press the ENTER button. 3 Press the ▲ or ▼ button to select Channel Manager , then press the ENTER button.
English - 15 Locking channels This feature allows you to prevent unauthorized users, such as children, from watching unsuitable programmes by muting out video and audio. 6 Press the ▲ or ▼ button to select Child Lock , then press the ENTER button.
English - 16 Assigning Names to Channels Channel names will be assigned automatically when channel information is broadcast. These names can be changed, allowing you to assign new names. 1 Press the MENU button to display the menu. 2 Press the ▲ or ▼ button to select Channel , then press the ENTER button.
English - 17 Customizing the Picture Settings Y our television has several setting options that allow you to control the picture quality . 1 Press the MENU button to display the menu. 2 Press the ENTER button to select Picture . 3 Press the ENTER button again to select Mode .
English - 18 Configuring Detailed Settings on the Picture Y ou can set detailed picture settings. 1 Press the MENU button to display the menu. 2 Press the ENTER button to select Picture . 3 Press the ▲ or ▼ button to select Detailed Settings , then press the ENTER button.
English - 19 White Balance : R-Offset/G-Offset/B-Offset/R-Gain/G-Gain/B-Gain/Reset Y ou can adjust the colour temperature for more natural picture colours. R-Offset/G-Offset/B-Offset/R-Gain/G-Gain/B-Gain : Changing the adjustment value will refresh the adjusted screen.
English - 20 Picture Options Y ou can set detailed picture settings. 1 Press the MENU button to display the menu. 2 Press the ENTER button to select Picture . 3 Press the ▲ or ▼ button to select Picture Options , then press the ENTER button. 4 Select the required option by pressing the ▲ or ▼ button, then press the ENTER button.
English - 21 DNIe: Off/Demo/On This TV includes the DNIe function so as to provide a high visual quality . If you set DNIe to on, you can view the screen with the DNIe feature activated. If you set the DNIe to Demo, you can view the applied DNIe and normal pictures on the screen, for demonstration purposes.
English - 22 − White : This function helps remove after images on the screen by changing the colour of pixels to white. Use this function when there are remaining after images or symbols on the screen especially when you displayed a still image on the screen for a long time.
English - 23 Equalizer : Balance/100Hz/300Hz/1kHz/3kHz/10kHz The television has several settings which allow you to control the sound quality . ➢ R/L Sound Balance Adjustment : T o adjust the sound balance of the R/L speakers.
English - 24 Selecting the Sound Mode (depending on the model) The DUAL I-II button displays/controls the processing and output of the audio signal. When pow er is switched on, the mode is automatically preset to either “DUAL-I” or “Stereo”, depending on the current transmission.
English - 25 T ime Features 1 Press the MENU button to display the menu. 2 Press the ▲ or ▼ button to select Setup , then press the ENTER button. 3 Press the ▲ or ▼ button to select T ime , then press the ENTER button. 4 Select the required option by pressing the ▲ or ▼ button, then press the ENTER button.
English - 26 Repeat : Select Once , Everyday , Mon ~ Fri , Mon ~ Sat , or Sat ~ Sun . V olume : Select the required volume level. Programme : When the On Time is active, you can turn on a specific channel. ➢ Y ou can set the hour , and minute directly by pressing the number buttons on the remote control.
English - 27 Entertainment : Off/Sports/Cinema/Game Entertainment mode enables you to select the optimal display and sound for sports, cinema and games. − Off : Switches the Entertainment function off. − Sports : Provides the optimal picture and sound quality for sports.
English - 28 V iewing the Picture in Picture (PIP) Y ou can display a sub picture within the main picture. In this way you can watch TV program or monitor the video input from any connected devices. 1 Press the MENU button to display the menu. 2 Press the ▲ or ▼ button to select Setup , then press the ENTER button.
English - 29 Setting up Y our PC Software (Based on Windows XP) The Windows display-settings for a typical computer are shown below . But the actual screens on your PC will probably be different, depending upon your particular version of Windows and your particular video card.
English - 30 Input Mode (PC) Both screen position and size will vary depending on the type of PC monitor and its resolution. The table below shows all of the display modes that are supported: D-Sub Input Mode Resolution Horizontal Frequency (kHz) V ertical Frequency (Hz) Pixel Clock Frequency (MHz) Sync Polarity (H/V) IBM 640 x 350 720 x 400 31.
English - 31 Setting the PC ➢ Preset to the PC mode by pressing the SOURCE button. 1 Press the MENU button to display the menu. 2 Press the ENTER button to select Picture . 3 Select the required option by pressing the ▲ or ▼ button, then press the ENTER button.
English - 32 Using the WISELINK Function This function enables you to view and listen to photo (JPEG) and audio files (MP3) saved on a USB Mass Storage Class (MSC) device. Press the POWER button on the remote control or front panel. Connect a USB device containing JPEG and/or MP3 files to the WISELINK jack (USB jack) on the side of the TV .
English - 33 Using the Remote Control Button in WISELINK Menu Button Operations Move the cursor and select an item. Select the currently selected item. Play or pause the Slide Show or MP3 file. Return to the previous menu. Run various functions from the Photo and Music menus.
English - 34 Using the PHOT O (JPEG) List This menu shows JPEG files and folders saved on an USB memory device. 1 Complete Steps 1 to 3 of Using the WISELINK Menu . (Refer to page 33) 2 Press the ◄ or ► button to move to Photo , then press the ENTER button.
English - 35 Using the Menu during a Slide Show Slide Show Speed: Select to control the slide show speed. Press the ▲ or ▼ button to select the required option( Fast , Normal , Slow ), then press the ENTER button. Background Music: Select to choose whether you want to play an MP3 file during a slide show .
English - 36 Using the Option Menu 1 Complete Steps 1 to 3 of Using the WISELINK Menu . (Refer to page 33) 2 Press the ◄ or ► button to move to Photo , then press the ENTER button. The saved file information is displayed as a folder or file. 3 Press the ▲, ▼, ◄ and ► button to select a file, then press the ENTER button.
English - 37 Using the MP3 List This menu shows MP3 files from among the files saved on a USB memory device. 1 Complete Steps 1 to 3 of Using the WISELINK Menu . (Refer to page 33) 2 Press the ◄ or ► button to move to Music , then press the ENTER button.
English - 38 Using the Setup Menu Setup displays the user settings of the WISELINK menu. 1 Complete Steps 1 to 3 of Using the WISELINK Menu . (Refer to page 33) 2 Press the ◄ or ► button to move to Setup , then press the ENTER button. 3 Press the ▲ or ▼ button to select an item you want, then press the ENTER button.
English - 39 Repeat Music: Select to determine whether to repeat playing the music when all MP3 files in the current folder have been played. Screen Saver: Select to set the waiting time before the screen saver appears. The screensaver will appear when no button is pressed for 1, 5 or 10 minutes.
English - 40 What is Anynet + ? Anynet+ is an A V network system that enables an easy-to-use A V interface for users by controlling all connected A V devices through the Anynet+ menu when Samsung Electronics A V devices are connected. Connecting Anynet + Devices The Anynet+ system supports A V devices supporting Anynet+ only .
English - 41 Continued... Setting Up Anynet + The following settings are to use Anynet+ functions. Using the Anynet+ Function 1 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Input , then press the ENTER button. 2 Press the ▲ or ▼ button to select Anynet+ (HDMI-CEC) , then press the ENTER button.
English - 42 Anynet+ Menu The Anynet+ menu changes depending on the type and status of the Anynet+ devices connected to the TV . Anynet+ Menu Description View TV Switches from Anynet+ to TV broadcast mode. Select Device Y our TV connects to the corresponding device.
English - 43 Listening through a Receiver Y ou can listen to sound through a receiver instead of the TV speaker . 1 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Input , then press the ENTER button. 2 Press the ▲ or ▼ button to select Anynet+ (HDMI-CEC) , then press the ENTER button.
English - 44 T eletext Feature (depending on the model) Most television stations provide written information services via teletext. The index page of the teletext service gives you information on how to use the service. In addition, you can select various options to suit your requirements by using the remote control buttons.
English - 45 The teletext pages are organized according to six categories: Part Contents A B C D E F Selected page number . Broadcasting channel identity . Current page number or search indications. Date and time. T ext. Status information. F ASTEXT information.
English - 46 W all Mount Kit Specifications (VESA) Install your wall mount on a solid wall perpendicular to the floor . When attaching to other building materials, please contact your nearest dealer . If installed on a ceiling or slanted wall, it may fall and result in severe personal injury .
English - 47 Entering the menu 1 Press the ▲, ▼, ◄ or ► button on your remote control. ➢ The Wall Mount Adjustment screen is displayed. ➢ If the Wall Mount Adjustment screen is not displayed when clicking on a direction button while watching your TV , use the menu to display that screen.
English - 48 How to assemble the Stand-Base (depending on the model) Using the screws for securing the stand base and the monitor , firmly attach the monitor to the stand base.
English - 49 T roubleshooting Before contacting the Samsung after-sales service, perform the following simple checks. If you cannot solve the problem using the instructions below, note the model and serial number of the television and contact your local dealer .
English - 50 Specifications Model Name PS50A550 Screen Size (Diagonal) 50 inch PC Resolution 1920 x 1080 @ 60 Hz Sound (Output) 10 W + 10 W Dimension (WxHxD) Body With stand 1231 x 770 x 95 mm 1231 x 831 x 320 mm Weight Body With stand 37.
Th i s p ag e i s i n t e n t i o n a l l y l e f t b l a n k . BN68-01447A-Eng.indb 51 2008-03-17 오후 5:38:37.
デバイスSamsung PS50A550の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Samsung PS50A550をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSamsung PS50A550の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Samsung PS50A550の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Samsung PS50A550で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Samsung PS50A550を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSamsung PS50A550の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Samsung PS50A550に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSamsung PS50A550デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。