SamsungメーカーSRP - 350の使用説明書/サービス説明書
ページ先へ移動 of 35
Operator’s Manual All specifications are subjected to change without notice SRP - 350 RECEIPT PRINTER.
2 Warning - U.S. This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FC C Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
3 Table of Contents CHAPTER 1. SETTING U P THE PRINTER ..................................... 4 1 - 1. U NPACKING ............................................................................ 4 1 - 2. C ONNECTING THE C ABLES ............................
4 Chapter 1. Setting Up the Printer 1 - 1. Unpacking Your printer box should in clude these items. If any items are damaged or missing, please contact your dealer for assistance.
5 1 - 2. Connecting the Cables You can connect up the three cables to the printer. They all connect to the connector panel on the back of t he printer, which is shown below: Notes : Before connecting any of the cables, make sure that both the printer and the host are turned off.
6 1 - 3. Connecting the computer You need an appropriate interface cable. 1. Plug the cable connector securely into the printer ’ s interface connector. 2. Tighten the screws on both sides of the cable connector. 3. Attach the other end of the cable to the computer.
7 1 - 5. Connecting the Power Supply CAUTIONS: When connecting or disconnecting the power supply from the printer, make sure that the power supply is not plugged into an electrical outlet.
8 1 - 6. Installing or Replacing the Paper Roll 1. Make sure that the printer is not receiving data; otherwise, data may be lost. 2. Open the paper rol l cover by pressing the cover - open button. 3. Remove the used paper roll core if there is one. 4.
9 5. Be sure to note the correct direction that the paper comes off the roll. 6. Pull out a small amount of paper, as shown. Then close the cover. 7. Tear off the paper as shown. Notes : When closing the cover, press the center of printer cover firmly to prevent Paper miss - loading.
10 1 - 7. Adjustments and Settings The SRP - 350 is set up at the factory to be appropriate for almost all users. It does, however, offer some setti ngs for users with special requirements. It has DIP switches that allow you to change communication settings, such as handshaking and parity check, as well as print density.
11 1 - 8. Using the Printer Control Panel Button The button can be disabled by the ESC c 5 command. Press the FEED button once to advance paper one line. You can also hold down the FEED button to feed pap er continuously. Panel lights POWER The POWER light is on whenever the printer is on.
12 Serial Interface (RS - 232C, RS - 485) Specification DIP Switch Set 1 Functions SW F UNCTION ON OFF DEFAULT 1 Data Receive Error Ignore Print ¡ ° ? ¡ ± OFF 2 Reserved - - OFF 3 HandShaking XON/.
13 Parallel /USB Interface Specification Dip Switch Set 1 Functions SW FUNCTION ON OFF DEFAULT 1 Reserved - - OFF 2 Reserved - - OFF 3 Reserved - - OFF 4 Reserved - - OFF 5 Reserved - - OFF 6 Reserved.
14 Chapter 2 . Hexadecimal Dumping This feature allows experienced users to see exactly what data is coming to the printer. This can be useful in fi nding software problems. When you turn on the hexadecimal dump function, the printer prints all commands and data in hexadecimal format along with a guide section to help you find specific commands.
15 Chapter 3 . The self test The self - test checks whether the printer has any problems. If the printer does not function properly, contact your dealer. The self - tes t checks the following; 1. Make sure paper roll has been installed properly. 2. Turn on the power while holding down the FEED button.
16 Chapter 4 . Code Table The following pages show the character code tables. To find the character corresponding to a hexadecimal number, count across the top of the table for the left digit and count down the left column of the table for the right digit.
17 Page 2 ( PC850 : Multilingual ).
18 Page 3 ( PC860 : Portuguese ).
19 Page 4 ( PC 86 3 : Canadian - French ).
20 Page 5 ( PC 865 : Nordic ).
21 Page 19 ( PC 8 58 : Euro ).
22 Page 255 ( Space Page ).
23 International Character Set.
24 Chapter 5 . Control Commands List Control codes Hexadecimal codes Function <HT> 09 Horizontal tab <LF> 0A Print and line feed <FF> 0C Print and return to standard mode in page mod.
25 Control codes Hexadecimal codes Function <ESC> nL nH 1B 5C n Set rel ative print position <ESC> a n 1B 61 n Select justification <ESC> c 3 n 1B 63 33 n Select paper sensor to out.
26 Control codes Hexadecimal codes Function <GS> k m … .NUL <GS> k m n … 1D 6B m … NUL 1D 6B m n … Print bar code <GS> r n 1D 72 n Transmit status <GS> v 0 m … .
27 APPENDIX A. Star Mode Command Summary Control codes Hexadecimal cod es Function <ESC> ” R ” n 1B 52 n Select international character set <ESC> <GS> t n 1B 1D 74n Select charac.
28 Control codes Hexadecimal codes Function <ESC> “ I ” n 1B 6C n Set left margin <ESC> “ Q ” n 1B 51 n Set right margin <LF> 0A Line Feed <ESC> “ a ” n 1B 61 n Fee.
29 Control codes Hexadecimal codes Function <SUB> 1A Control peripheral device #2 immediately <ESC> “ d ” n 1B 64 n Partial - cut command to the auto cutter.
30 B. Connectors SRP - 350 /SRP - 350S Connector ( Serial Interface ) SRP - 35 0P Connector ( Parallel Interface ) SRP - 350 U Connector ( USB Interface ).
31 Interface Connector Serial Interf ace (RS - 232) Pin No. Signal name Direction Function 1 FG - Frame Ground 2 TxD Output Transmit Data 3 RxD Input Receive Data 6 DSR Input Data Set Ready 7 SG - Signal Ground 20 DTR Output Data Terminal Ready Serial Interface(RS - 485) Pin No.
32 Parallel I nterface(IEEE - 1284) Pin No. Source Compatibility Mode Nibble Mode Byte Mode 1 Host nStrobe HostClk HostClk 2 Host / Printer Data 0 (LSB) - Data 0 (LSB) 3 Host / Printer Data 1 - Data 1.
33 USB Interface Pin No. Signal Name Assignment (Color) Function Shell Shield Drain Wire Frame Ground 1 VBUS Red Host Pow er 2 D - White Data Line(D - ) 3 D+ Green Data Line(D+) 4 GND Black Signal Gro.
34 Drawer Connector Pin No. Signal name Direction 1 Frame ground - 2 Drawer kick - out drive signal 1 Output 3 Drawer open/close signal Input 4 +24V - 5 Drawer kick - out drive signal 2 Output 6 Signal ground - C. Notes Paper dust inside the printer may lower the print quality.
35 D. Specification Printing method Thermal line printing Dot density 180 X 180 dpi (7dots/mm) Printing width 72. 192 +0.2 mm or – 0.2mm Paper width 79 ~ 80 mm Charac ters per line (default) 42 (Font A) 56 (Font B) Printing speed 35.
デバイスSamsung SRP - 350の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Samsung SRP - 350をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSamsung SRP - 350の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Samsung SRP - 350の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Samsung SRP - 350で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Samsung SRP - 350を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSamsung SRP - 350の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Samsung SRP - 350に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSamsung SRP - 350デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
