SamsungメーカーSRP-350PLUSA&Cの使用説明書/サービス説明書
ページ先へ移動 of 22
User ’ s Manual SRP-350plusA&C Thermal Printer Rev . 1.02 http://www .samsungminiprinters.com ٻ.
Rev . 1.02 - 2 - SRP-350plusA&C ഓ Safety Precautions In using the present appliance, please keep the following safety regulations in order to prevent any hazard or material damage. W ARNING Violating following instructions can cause serious injury or death.
Rev . 1.02 - 3 - SRP-350plusA&C CAUTION Violating fo llowing inst ructions can cause s light wound or dam age the appliance. If you observe a strange smoke, odor or noise from the printer , unplug it before t aking following measures. ח͑ Switch off the printer and unplug the set from the mains.
Rev . 1.02 - 4 - SRP-350plusA&C ഓ W arning - U.S.A This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Rev . 1.02 - 5 - SRP-350plusA&C ഓ Introduction The SRP-350plus Roll Printer are designed for use with electronic instruments such as system ECR, POS, banking equipment, computer peripheral equipment, etc. The main features of the printer are as follows: 1.
Rev . 1.02 - 6 - SRP-350plusA&C ഓ T able of Content s 1. Setting Up the Printer ................................................................................................... 7 1-1 Unpackin g ................................................
Rev . 1.02 - 7 - SRP-350plusA&C 1. Setting Up the Printer 1-1 Unpacking Y our printer box should include these items. If any items are damaged or missing, please contact your dealer for assist ance.
Rev . 1.02 - 8 - SRP-350plusA&C 1-2 Connecting the Cables Y ou can connect up the three cables to the printer . They all connect to the connector panel on the back of the printer , which is shown below: NOTE Before connecting any of the cables, make sure that both the printer and the host are turned off.
Rev . 1.02 - 9 - SRP-350plusA&C 1-2-2 Parallel Interface (IEEE1284) Interface connector Drawer kick-out connector Power supply connector Pin No. Source Compatibility Mode Nibble Mode Byte Mode 1 H.
Rev . 1.02 - 10 - SRP-350plusA&C 1-2-3 USB2.0 Interface Drawer kick-out connector Power supply connector USB2.0 connector Pin No. Signal Name Assignment (Color) Function Shell Shield Drain Wire Fr.
Rev . 1.02 - 1 1 - SRP-350plusA&C 1-4 Setting the Dip Switches 1-4-1 Serial Interface (RS-232C) • DIP Switch 1 SW Function ON OFF Default 1-1 Auto Line Feed Enable Disable OFF 1-2 Handshaking XO.
Rev . 1.02 - 12 - SRP-350plusA&C • T able 1 – Baud rate (bp s) Selection T ransmission S peed 1-6 1-7 1-8 Default 2400 ON OFF OFF 4800 ON OFF ON 9600 OFF ON OFF 19200 OFF OFF OFF 38400 OFF ON .
Rev . 1.02 - 13 - SRP-350plusA&C 1-5 Setting the Memory Switches This printer has “Memory Switch” set which is software switches. Memory Switch set has “MSW1”, “MSW2”, “MSW8”, “MSW9” “Customize value”, “Serial communication condition”.
Rev . 1.02 - 14 - SRP-350plusA&C MSW2-8 MSW2-7 MSW2-6 MSW2-5 MSW2-4 MSW2-3 Character T able OFF OFF OFF OFF OFF OFF Page 0 437 (USA, S tandard Europe) OFF OFF OFF OFF ON OFF Page 1 Kat akana OFF O.
Rev . 1.02 - 15 - SRP-350plusA&C 1-6 Installing or Replacing the Paper Roll NOTE Be sure to use paper rolls that meet the specifications. Do not use p aper rolls that have the paper glued to the core because the printer cannot detect the p aper end correctly .
Rev . 1.02 - 16 - SRP-350plusA&C 1-6-5 Be sure to note the correct direction that the paper comes of f the roll. 1-6-6 Pull out a small amount of p aper , as shown. Then close the cover . NOTE When closing the cover , press the center of printer cover firmly to prevent paper miss-loading.
Rev . 1.02 - 17 - SRP-350plusA&C 1-7 Adjustments and Settings The SRP-350plus is set up at the factory to be appropriate for almost all users. It does, however , offer some settings for users with special requirement s.
Rev . 1.02 - 18 - SRP-350plusA&C 1-9 Connecting the computer Y ou need an appropriate interface cable. 1-9-1 Plug the cable connector securely into the printer ’s interface connector . 1-9-2 T ighten the screws on both sides of the cable connector .
Rev . 1.02 - 19 - SRP-350plusA&C 2. Self test The self-test checks whether the printer has any problems. If the printer does not function properly , contact your dealer . The self-test checks the following; 2-1 Make sure paper roll has been inst alled properly .
Rev . 1.02 - 20 - SRP-350plusA&C 3. Hexadecimal Dumping This feature allows experienced users to see exactly what data is coming to the printer . This can be useful in finding software problems.
Rev . 1.02 - 21 - SRP-350plusA&C 4. Specification Item Details Printing Method Thermal Line Printing Dot Density SRP-350plus: 180 X 180 d pi (7dots/mm) SRP-352plus: 203 X 203 dpi (8dot s/mm) Printing Width 57.
Rev . 1.02 - 22 - SRP-350plusA&C 5. Appendix 5-1 Cleaning Printer Paper dust inside the printer may lower the print quality . In this case clean the printer as follows. 5-1-1 Open the printer cover and remove the paper if exist s. 5-1-2 Clean the print head with a cotton swab moistened with alcohol solvent.
デバイスSamsung SRP-350PLUSA&Cの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Samsung SRP-350PLUSA&Cをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSamsung SRP-350PLUSA&Cの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Samsung SRP-350PLUSA&Cの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Samsung SRP-350PLUSA&Cで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Samsung SRP-350PLUSA&Cを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSamsung SRP-350PLUSA&Cの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Samsung SRP-350PLUSA&Cに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSamsung SRP-350PLUSA&Cデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
