SanyoメーカーCLT-2422の使用説明書/サービス説明書
ページ先へ移動 of 20
Important Charge the handset battery for 12 continuous hours prior to first use. 2.4 GHz Cordless T elephone with Caller ID Instruction Manual CL T -2418 CL T -2422 SANYO Canada Inc.
MUTE key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Low battery warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 VOICE MAIL/IN USE indicator . . . . . . . . . . . . . . . . . . . . . . . .
GETTING ST ARTED Checking the package contents Make sure your package includes the items shown here. Modular jack Y ou need an RJ11 type modular phone jack. If you do not have a modular jack, call your local phone company to find out how to get one installed.
Mounting on a wall Do not attempt to wall-mount the phone before initial 12-hour charging is completed. Follow steps 1– 3 above to charge the handset. 4. Remove the handset from the base and set aside. T urn the base over and align the four slots on the bottom of the base with the four hook-tabs on the bracket.
NAMES AND CONTROLS Base unit 9 NAMES AND CONTROLS Handset 8 T ALK/CALL BACK key (also used to END a call) LCD screen VOLUME keys CID ▲ or ▼ key 7-10-11/HOLD key 7-10-11 CID DISPLA Y key HOLD key R.
Area code setting For proper Caller ID operation, you must enter your area code. This setting can only be done from the base. 1. Make sure the phone is OFF (not in T ALK mode). 2. Press FLASH/PROGRAM three times. S S E E T T A A R R E E A A C C O O D D E E shows on screen.
BASICS Receiving a call When an incoming call is received, both handset and base screens light and show caller information*. The incoming call LED on the handset and the SPEAKER key on the base flash. * A subscription is required from your local phone company to receive Caller ID information on your phone.
Ringer switch and volume Handset ringer: The RINGER switch must be on for the handset to ring during incoming calls. Base ringer: 1. Make sure the speakerphone is OFF ( SPEAKER key is not lit). 2. T o increase the ringer volume to the highest level, press VOLUME ▲ .
• Handset to speakerphone – When the handset is in talk mode press HOLD to put the caller on hold, and then place the handset in the base. Y ou are automatically connected to the caller through the speakerphone.
Conferencing from the handset: 1. Press T ALK/CALL BACK . 2. Dial the number you want to call. The telephone number shows on screen. 3. Press SPEAKER on the base. C C O O N N F F E E R R E E N N C C E E shows on the base and handset screens. 4. When finished, press T ALK/CALL BACK on the handset and SPEAKER on the base.
21 Ti p : Do not use T ALK/CALL BACK (or SPEAKER on base) to activate custom calling services such as Call W aiting, or you will hang up the phone. CHAN (Channel) key While talking, you might need to manually change the channel in order to get rid of static.
Reviewing Caller ID list As calls are received and stored, the screen is updated to let you know how many calls have been received. 1. Press CID ▼ to scroll through the Caller ID list from the most recent to the oldest. Y ou can also use the CID ▲ or ▼ key on the base.
DIRECTORY Y ou may store up to 20 numbers (up to 24-digits) in memory for quick dialing. The directory locations for the base and handset are separate, with 10 memory locations for each. This directory feature is in addition to the 40 Caller ID list. Storing a name/number in the directory The phone must be OFF (not in T ALK mode).
Reviewing and deleting directory contents 1. Make sure the phone is OFF (not in T ALK mode). 2. Press MEM . 3. Use CID ▲ or ▼ to scroll through the directory until the desired name/number is shown, or use the number pad to select a memory location.
RECYCLING NICKEL-MET AL HYDRIDE BA TTERIES NICKEL-MET AL HYDRIDE BA TTERIES MUST BE DISPOSED OF PROPERL Y . Please take your used battery pack to a store that recycles Ni-MH batteries. POWER FAILURE During the period that the power is off, you will not be able to make or receive calls with the telephone.
SOUND SIGNALS A long warbling tone Signals an incoming call Single T one A key is pressed T wo Long Beeps Confirmation tone One short beep and one long beep Page signal Three short beeps Error tone/Ou.
VOICE MAIL/IN USE indicator on the base flashes •P rovided your phone company offers voice mail indicator service and you subscribe to it, VOICE MAIL/IN USE indicator flashes when the phone is not in use to indicate there is a message waiting. It stops flashing after the message has been reviewed.
35 34 REN Number: The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The REN number of this phone is located on the bottom of the base unit.
37 36 d. Communications products not intended for Canadian usage or products without appropriate Canadian regulatory approvals. e. Problems due to product set-up and installation. f. Adjustments that are outlined in the Operating Manual. g. Accessory items including antenna, and batteries, h.
38 SOS HELP LINE At Sanyo, fulfilling the needs of our customers is a priority . That’ s why we created our SOS customer service program that guarantees satisfaction.
デバイスSanyo CLT-2422の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Sanyo CLT-2422をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSanyo CLT-2422の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Sanyo CLT-2422の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Sanyo CLT-2422で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Sanyo CLT-2422を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSanyo CLT-2422の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Sanyo CLT-2422に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSanyo CLT-2422デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
