SanyoメーカーDSR-3709Pの使用説明書/サービス説明書
ページ先へ移動 of 126
CARD CARD MENU RESET EJECT CARD CARD MENU RESET EJECT e00_l8hbg_xe_7.book Page 1 Friday, Novem ber 5, 2004 10:21 AM.
English 1 PRECAUTION Location For safe operation and satisfactory performance of your unit, keep the following in mind when selecting a place for its installation: Shield it from direct sunlight and kee p it away from sources of intense heat. Avoid dusty or humid places.
2 English INTRODUCTION Main features The digital video record er records video from monitoring cameras to its internal hard disk, it can display the video being displayed on a monitor split into four, nine or sixtee n screens, and it can also display reco rded video in the same way.
English 3 CONTENTS 1 BEFORE USE .............. ................ ................ .. 5 Notes on handling the internal HDD .............. 5 Notes on installation loc ations ....................... 5 The hard disk and cooling fa n are consumable components.
CONTENTS 4 English OPERATION INTRODUCTION SETTINGS OTHER 1 MENU CONFIGURATION AND OPERATIONS .......... ................... ................ 47 Basic menu operations ....................... ......... 47 Restoring menu setting items to their default values .
English 5 1 BEFORE USE Notes on handling the internal HDD This digital video recorder uses an internal hard disk drive (HDD). Be sure to observe the following points carefully when operating, setting-up, or servicing the digital video recorder. Do not subject the digital vid eo recorder to sudden impact or vibration.
BEFORE USE 1 6 English INTRODUCTION The hard disk and cooling fan are consumable components. If used in an ambient temperature of 25ºC, the hard disk should generally be replaced after 2 years; and the cooling fan after 3 years.
English 7 2 NAMES AND FUNCTIONS OF PARTS Front panel 1. POWER indicator The POWER indicator will light up when the power is turned on. If the internal HDD or fan begins to malfunction, this indicator will be flashed .
NAMES AND FUNCTIONS OF PARTS 2 8 English INTRODUCTION 11. [PLUS] button and indicat or ( J P.20) The [PLUS] button is used to enlarge video from a single camera to quad screen size during multi 9 or multi 16 screen display. For DSR-3709P, this operation is availabl e only when in multi 9 screen d isplay.
NAMES AND FUNCTIONS OF PARTS 2 English 9 22. [TIMER] butto n and indicator ( J P.23) If the [TIMER] button is pressed while the recording is stopped, timer recording standby mode is adopted and recording will then start automa tically at the set time.
NAMES AND FUNCTIONS OF PARTS 2 10 English INTRODUCTION Rear panel 1. VIDEO IN terminals The DSR-3709P has nine VIDEO IN terminals. 2. VIDEO OUT terminals The DSR-3709P has nine VIDEO OUT terminals. 3. [ALL RESET] button When the [ALL RESET] button is pressed, the digita l video recorder is reset and the time is returned to its default setting.
English 11 3 INSTALLATION AND CONNECTIONS This section describes how to connect the digita l video recorder to video cameras and other devices. Be sure to read the instruction manual s for each connected device. z Improper connections can result in malfunction or th e emission of smoke.
INSTALLATION AND CONNE CTIONS 3 12 English INTRODUCTION Connection The digital video recorder supp orts both straight type and crossed type connection cables. When using a straight type connection cable, connect the RS-485 connector’s pin A to the pin A socket, or pin B to the pin B socket.
INSTALLATION AND CONNE CTIONS 3 English 13 Turn off all devices a nd use a coaxial cable to connect the devices. 1 Connect cameras to the VIDEO IN terminals. 2 Set the protocols and address in the <CAMERA CONTROL SET> screen. ( J P.97) 3 Operate the dome cameras with the front panel buttons.
INSTALLATION AND CONNE CTIONS 3 14 English INTRODUCTION The SENSOR ALARM OUT terminal s are used to relay alarm signals whene ver one of the digital video recorder’s motion sensors is triggered. Normally i n an open condition, a terminal adopts low condition when a sensor for the corresponding camera numb er has been triggered.
English 15 1 PREPARING FOR USE Whenever the power is turned on, the ope ration display area will be shown at the top of the monitor screen. This area indicates the date, time, picture quality, and other information nee ded for operation. (1) Date display ( J P.
PREPARING FOR U SE 1 16 English OPERATION 1 Press the [EXIT/OSD] button. As the [EXIT/OSD] button is pressed , the operation display area moves to a different locatio n or is hidden. Use the following procedure to set the language displayed on the mo nitor.
PREPARING FOR U SE 1 English 17 4 Turn the shuttle dial clockwise, and then turn the jog dial to select the desired language. The set item flashes. 5 When you have made a selection, turn the shuttle dial clockwise. The cursor moves to the date and time .
PREPARING FOR U SE 1 18 English OPERATION Hard disk recording areas When the digital video recorder is turned on , recording areas are automatically setup wi thin the interna l hard disk (with the default se ttings being normal recording area: 80%, alarm recording area: 1 9%, and archive area: 1 %).
English 19 2 VIEWING VIDEO FROM A CAMERA Example: Selecting Camera 2 1 Press the No. 2 [CAMERA SELECT] button. The No. 2 CAMERA SELECT indicator lights up and video from Camera 2 is displayed on a full screen. Images can be enlarged while monitori ng on a full screen.
VIEWING VIDEO FROM A CAMERA 2 20 English OPERATION 1 Press the [MULTI] button. The MULTI indicator lights up and video from nine separate cameras is displayed simultaneously. Press the [MULTI] button again to display vid eo from 16 cameras. The DSR-3709P can only display vid eo from nine cameras.
VIEWING VIDEO FROM A CAMERA 2 English 21 Use the following p rocedure when viewing a full screen to have the displayed video ch ange automatically based on camera numbers. 1 Press the [SEQUENCE] button. The SEQUENCE indicator starts to flash and the displayed video changes automatically based on camera numbers.
VIEWING VIDEO FROM A CAMERA 2 22 English OPERATION z Monitor 2 operation is n ot possible when a menu screen is being displayed. z As the [EXIT/OSD] button is pressed, the operating display moves to a different location or is hidden in the same manner as the main monitor.
English 23 3 RECORDING Use the following procedure to record the monitored video in the normal recordi ng area. Recording will not be possible until a time h as been set for the digital video recorder. Ma ke su re to set the time. ( J P.17) 1 Press the [REC/STOP] button.
RECORDING 3 24 English OPERATION Use the following procedure to auto matically record alarm video to the alarm recording area whe n an alarm signal is detected. Recording will not be possible until a time h as been set for the digital video recorder. Ma ke su re to set the time.
RECORDING 3 English 25 Use the following procedure to record video from immediately before occurrence of an alarm. 1 Set pre-alarm recording. Follow the instructio ns on P.79 set “7. ALARM REC MODE SET” from <RECORD SET> to “P RE-ALARM RECORDING”.
26 English OPERATION 4 PLAYBACK Use the following procedure to play video stored in the normal recording area (during normal or timer reco rding). 1 Press the [PLAY/STOP] button. The PLAY/STOP indicator lights up, and “ ” appe ars in the operation display area.
PLAYBACK 4 English 27 (1) Performing fast-forward. When the jog dial is turned clockwise, fast-forward playback is started and the symbol “ ” appears in the op eration display area.
PLAYBACK 4 28 English OPERATION z In this way, move the zoom frame to enclose the area of video to be magnified. 3 Turn the shuttle dial clockwise. The area enclosed by the zoom frame is magnified (b y a factor of 2). 4 Press the [ZOOM] button. Magnification is cancelled and the display returns to the normal screen.
PLAYBACK 4 English 29 1 Turn the jog dial clockwise or counter- clockwise while playba ck is paused. Clockwise: The still i mage is moved forward by one frame or field. Counter-clockwise: The still image is moved back by one frame or field. z The jog dial can be turned to i ncrease the speed of frame advance.
30 English OPERATION 5 SEARCHING FOR RECORDED VIDEO Images stored in the normal recordin g area, alarm recording ar ea or archive area can be located by searching and can then be played back. Use one of the following five search me thods to locate the required video .
SEARCHING FOR R E CORDED VIDEO 5 English 31 Use the following procedure to search and pla yback all video stored in the alarm recording ar ea. If pre-alarm video is being recorded, playback will start from immediately before the alarm. 1 Press the [SEARCH] button while the digital video recorder is recording or stopped.
SEARCHING FOR R E CORDED VIDEO 5 32 English OPERATION Use the following procedure to display all of the alarm recordings stored in the alarm recording area as thumbnai ls list. 1 Press the [SEARCH] button while the digital video recorder is recording or stopped.
SEARCHING FOR R E CORDED VIDEO 5 English 33 3 Turn the shuttle dial clockwise. The <TIME/DATE SEARCH> screen is displayed. (1) RECORDING TOP: Indicates the date/time of the earliest video recording. (2) RECORDING END: Indicates the date/time of the most-recent video recording.
SEARCHING FOR R E CORDED VIDEO 5 34 English OPERATION Use the following procedure to playback vide o that has been stored in the archive area. 1 Press the [SEARCH] button while the digital video recorder is recording or stopped. The SEARCH indicator lightsup and the <SEARCH> screen is displa yed.
SEARCHING FOR R E CORDED VIDEO 5 English 35 2 Turn the jog dial to select “MOTION DETECTION SEARCH”, and then turn the shuttle dial clockwise. The <MOTION DETECTION SEARCH> screen is displayed. 3 Turn the jog dial to select “SEARCH FROM”, and then turn the shuttle dial clockwise.
SEARCHING FOR R E CORDED VIDEO 5 36 English OPERATION 1 Turn the shuttle dial clockwise whil e video is being displayed on the preview screen. (1) Turn the jog dial to set the start date and time fo r motion sensing (i.e., 10 AM on the same day), and then turn the shuttl e dial clockwise.
SEARCHING FOR R E CORDED VIDEO 5 English 37 6 Turn the jog dial to select “PREVI EW”. 7 Turn the shuttle dial clockwise. Each time the shuttle dial is turned clockwise, a different motion sensor screen will be displayed on the preview screen. If “NOT FOUND” is dis played Carry out motion sensor setting again.
38 English OPERATION 6 SAVING (COPYING) RECORDED VIDEO Use the procedures described below to co py important video stored in the no rmal re cordin g area or the alarm recording area to the digital video recorder’s archive area, a Comp actFlash card, a Microdrive or CD-R/RW.
SAVING (COPYI NG) RECORDED VIDEO 6 English 39 1 Play video from the normal recording area or the alarm recording area. 2 Press the [STILL] button whe n the frame to be copied is displayed. z Images from all cameras cannot be copied simultaneously. Use the ap propriate [CAMERA SELECT] button to select the camera whose video is to be copied.
SAVING (COPYI NG) RECORDED VIDEO 6 40 English OPERATION 7 Turn the shuttle dial clockwise. “PICTURES” flashes. 8 Turn the jog dial to select “SECONDS”. [Settings] ( indicates default setting) 9 Turn the shuttle dial clockwise. The cursor moves to “START”.
SAVING (COPYI NG) RECORDED VIDEO 6 English 41 Use the following procedure to copy video either to a Microdrive and to a CompactFla sh card (Supported up to 2 GB). 1 Insert a CompactFlash card. Insertion method Removal method 2 Pause playback on the image to be copied, and then press the [COPY] button.
SAVING (COPYI NG) RECORDED VIDEO 6 42 English OPERATION [Settings] ( indicates default setting) z Up to 40,000 images can be co pied in a single operation. When specifying th e number of images using “MINUTES”, copying will end at the point at which 40,000 images are co pied.
SAVING (COPYI NG) RECORDED VIDEO 6 English 43 When images are copied to a Co mpactFlash card, following folders are created and image s are saved within them. (1) A folder with the name “SANYO” is created inside the root directory. (2) Within "SANYO," a folder with the date on which images were copied to is created.
SAVING (COPYI NG) RECORDED VIDEO 6 44 English OPERATION 4 Turn the jog dial to select “CF -> PRINT”, and then turn the shuttle dial clockwise. The cursor moves to “HOW MANY”. 5 Turn the shuttle dial clockwise, and then turn the jog dial to set “HOW MANY”.
SAVING (COPYI NG) RECORDED VIDEO 6 English 45 1 Connect a recordable CD-R/RW drive and insert a disk. z The digital vide o recorder has one USB terminal on th e front and one on the back, but they cannot be used simultaneously. Connect recordable drive to either terminal.
SAVING (COPYI NG) RECORDED VIDEO 6 46 English OPERATION z Up to 40,000 images can be co pied in a single operation. When specifying th e number of images using “MINUTES”, copying will end at the point at which 40,000 images are co pied. z Alarm recordings can only be copied one eve nt at a time.
English 47 1 MENU CONFIGURATION AND OPERATIONS This section describes the menu config uration and the menu items to be selected for each operation . 1 Press the [MENU] button. The MENU indicator lights up and the <MAIN MENU> is displayed. 2 Turn the jog dial to select a menu.
MENU CONFIGURATION AND OPERATIONS 1 48 English SETTINGS The jog dial and shuttle dia l are used for movement and confirmation in sub-men us and setting screens. Use the [CAMERA SELECT] buttons o n the front panel to enter numbers and channels (camera nu mbers).
MENU CONFIGURATION AND OPERATIONS 1 English 49 The following table indicates the sub-menus or setting scre ens displayed by selecti ng items from the <MAIN MENU>. The [MENU] button can be used in an y sub-menu to scroll through each of the sub-menus in se quence.
MENU CONFIGURATION AND OPERATIONS 1 50 English SETTINGS 4 <SCREEN SET> This sub-menu is used to make screen settings for monitoring. (1) MULTI SCREEN ( J P.100) Specifies the positions of video from different cameras on the quad, multi 9 and 16 screens.
English 51 2 INITIAL SET The <INITIAL SET> is used to make the following setting. Setting of the date and time displayed on the normal scr een. See P.17 for more details. 1 Press the [MENU] button. The MENU indi cator lights up and the <MAIN MENU> is displayed.
INITIAL SET 2 52 English SETTINGS 3 Turn the jog dial to select “1. LANGUAGE/CLOCK SET”, and then turn the shuttle dial clockwise. The <LANGUAGE/LANGUE/ SPRACHE/IDIOMA> screen is displayed. 4 Turn the jog dial to select “MODE” under <SUMMER TIME SET>.
INITIAL SET 2 English 53 11 Select month with the jog dial or numeric keys and turn the shuttle dial clockwise. The cursor moves to the time. 12 Select time with the jog dial or numeric keys and turn the sh uttle dial clockwise. The cursor moves to the minutes portion of the time.
INITIAL SET 2 54 English SETTINGS 9 Use the same procedure to set the time for all subsequent recorders. When you have finished making the setti ngs, the display returns to the normal screen. The default setting value is “01:00”. z Set the time to th e same time of first digita l video recorder.
INITIAL SET 2 English 55 Use the following procedure to set a unique ti tle for each camera so that th ese titles can b e displayed on-scre en. Titles can be up to 10 characters in length per camera. The following characters can be used. z Letters: A to Z z Numbers: 0 to 9 z Symbols: - : .
INITIAL SET 2 56 English SETTINGS Use the following procedure to set specific dates as holidays to have the ope ration for Sunday used on those days also. Dates such as nati onal holidays and compan y off days should be set as holidays when you want th ose dates to have the same timer operation as Sundays.
INITIAL SET 2 English 57 A time period is setup by t he two timers TIME PERIOD A and TIME PERIOD B, and the following pro cedure can be used to sp ecify four d iffer ent periods per day based on time period settings (for instance, early morning, mornin g, lunchtime, and night).
INITIAL SET 2 58 English SETTINGS Example 1: Setting period s using TIME PERI OD A and TIME PERIOD B z TIME PERIOD A settings Set T-1 to 6 AM (6:00) Set T-2 to 11:30 AM (11:30) Set T-3 to 1:30 PM (13:.
INITIAL SET 2 English 59 9 In the same manner as described set the hours and minutes of T-1, T-2, T -3, and T-4 for “TIME PERIOD B” settings. For both TIME PERIOD A and TIME PERIOD B, all settings are “00: 00” by default. z Settings for T-1 through T-4 cannot be made in such a way that they extend over two days (i.
60 English SETTINGS 3 RECORD SET The <RECORD SET> is used to make the following settings. Use the following pro cedures to make simple recording settings. Two different se tting methods may be used -- one based on r ecording days; the other based on recording rate.
RECORD SET 3 English 61 1 Press the [MENU] button. The MENU indicator lights up and the <MAIN MENU> is displayed. 2 Turn the jog dial to select “2. RECORD SET”, and then turn the shuttle dial clockwise. The <RECORD SET> screen is displayed.
RECORD SET 3 62 English SETTINGS 8 To activate timer operation, turn the jog dial to select “ON”, and then turn the shuttle dial clockwise. The cursor moves to “START”. If timer recording has been set to “ON”, set the timer’s “START” and “STOP” with the jog dial or numeric keys.
RECORD SET 3 English 63 z The recording rate is automatically calculated based on recording settings and the number of conne cted cameras, and this is indicated by “REC RATE”. All cameras will record at this rate. If a valid figure cannot be calculated, “ERROR!” will be displayed.
RECORD SET 3 64 English SETTINGS 10 Set “AUDIO RECORDING”. See P.62. 11 Turn the shuttle dial counter-clockwise. The <WARNING> screen is displayed. 12 Turn the jog dial to select “YES”, and then turn the shuttle dial clockwise. The display returns to the <NORMAL REC EASY SET> screen.
RECORD SET 3 English 65 Total capacity following hard disk expansion . When “MIRRORING” ( J P.93) is set using “4. HDD SET”, the total capacity di splay will change as follows. z If “MIRRORING” is “OFF”, the capacity for hard-disk expansion is displayed.
RECORD SET 3 66 English SETTINGS 3 Set “ALARM RECORDING AREA” to 49% and turn the shuttle dial to the right. The cursor moves to “AREA FULL RESET.” 4 Turn the shuttle dial counter- cloc kwise. The <WARNING> screen is displayed. The screen contains a message regarding initial ization of the hard disk.
RECORD SET 3 English 67 2 Turn the jog dial to select “2. RECORDING AREA SET” from the <RECORD SET> screen, and then turn the shuttle dial clockwise. The <RECORDING AREA SET> scre en is displayed. 3 Turn the jog dial to select “AREA FULL RESET”, and then turn the shuttle dial clockwise.
RECORD SET 3 68 English SETTINGS 2 Turn the jog dial to select setting (OFF, for example), and then turn the shuttle dial clockwise. “REMAINING DISK WARNING” changes to “1%” from “**”.
RECORD SET 3 English 69 Use the following procedure to perform series recording when this digital video recorder is connected to other digital video recorde rs. If series recording is set and normal recordin g area or alarm recording area remaining memory runs out, recording can be continued on a another digital video recorder.
RECORD SET 3 70 English SETTINGS 3 Set depending on your recording need s. z Alarm recording cannot be recorded alone. Set to combine with normal record ing or timer recording. z Normal recording and timer re cording cannot be set simultaneously. If both ar e set, timer recording is enabled.
RECORD SET 3 English 71 You can set a storage period for re corded data as described below. When the set pe riod has expired, the corresponding data will be automatically deleted. 1 Turn the jog dial to select “AUTO DELETE”, and then turn the shuttle dial clockwise.
RECORD SET 3 72 English SETTINGS 5 Turn the jog dial to select “PICTURE QUALITY”, and then turn the shuttle dial clockwise. [Settings] ( indicates default setting) z The file size is intended as a general guideline and actual sizes w ill depend on th e recorded video.
RECORD SET 3 English 73 Use the following p rocedure to record from specified cameras. A total of four programs (No. 1 through No. 4) can be setup for this purpose. For example, Program No. 1 could be setup to record from cameras No. 1 through No. 4 only, whereas Program No.
RECORD SET 3 74 English SETTINGS 6 Turn the jog dial to select a recording rate (6.25, for example), and then turn the shuttle dial clockwise. Camera No. 1 is no w set to re cord at a rate of 6.25. The cursor moves to “02”. Valid recording rates 25*, 12.
RECORD SET 3 English 75 z The settings made using <NORMAL REC MODE SET> are used to set quality and audio recording for timer recording. ( J P.71) z Set recording rate to above 1 FPS when performi ng audio recordi ng. z If the start and end times are on different days (i.
RECORD SET 3 76 English SETTINGS 1 Press the [MENU RESET] button with the <TIMER SET> screen displayed. All setting items are cleared. Use the following p rocedures to set timer recordings spanning more than 24 hours. T he 7th (SAT) and 8th (DLY) lines from the <TIMER SET> screen are used for this purpose.
RECORD SET 3 English 77 Use the following proce dure to control the start an d end of recording in response to signals received via the EXT TIMER ON terminal on the rear of the digital video recorder.
RECORD SET 3 78 English SETTINGS 2 Turn the jog dial to select “7. ALARM REC MODE SET”, and then turn the shuttle dial clockwise. The <ALARM REC MODE SET> screen is displayed. 3 Turn the shuttle dial clockwise. “OFF” flashes. 4 Turn the jog dial to select “ALARM RECORDING”, and then turn the shuttle dial clockwise.
RECORD SET 3 English 79 7 Set “ALARM INTERLEAVE”. [Settings] ( indicates default setting) * Recording pattern for “SW” and “ONLY” 8 Set “REC RATE” and “DURATION”. The maximum number of recording alarms (shown in parentheses) changes in accordance with the new settings.
RECORD SET 3 80 English SETTINGS 2 Turn the jog dial to change “OFF” to “ON”, and then turn the shuttle dial clockwise. A message appears indicating automatic rate adjustment. “NO” flashes. [Settings] ( indicates default setting) 3 Turn the jog dial to select “YES” for warning message, and then turn the shuttle dial clockwise.
RECORD SET 3 English 81 Use this setting to indicate how alarms are to be detected. 1 Turn the jog dial to select “ALARM TRIGGER”, and then turn the shuttle dial clockwise. “ALARM” flashes in the “ALARM TRIGGER” field. 2 Turn the jog dial to select an alarm detection method, and then turn the shuttle dial clockwise.
RECORD SET 3 82 English SETTINGS 1 Make timer settings for “TIME PERIOD A” and “TIME PERIOD B” from <TIME PERIOD SET>. ( J P.57) 2 Turn the jog dial select “MOTION SENSOR”, and then turn the shuttle dial clockwise. The motion sensor scree n is displayed.
RECORD SET 3 English 83 11 Turn the jog dial to set the sensitivity (OFF or 1 through 10), and then turn the shuttle dial clockwise. The cursor moves to “MODE”. [Settings] ( indicates default setting) 12 Turn the shuttle dial clockwise. “A” flashes for the “MODE”.
RECORD SET 3 84 English SETTINGS z The period for “T-1” through “T-4” as set in step 9 changes to th at of “TIME PERIOD A” or “TIME PERIOD B” on P.57. z When time period is unset, T-1 settings are enabled and T-2 through T-4 are disabled.
RECORD SET 3 English 85 2 Turn the jog dial to set “MAIN MON. DISPLAY”, and then turn the shuttle dial clockwise. The cursor moves to “ALARM PRIORITY”. 3 Turn the shuttle dial clockwise and turn the jog dial to set “ALARM PRIORITY”, and then turn the shuttle dial clockwise once again.
86 English SETTINGS 4 GENERAL SET The <GENERAL SET> is used to make the following settings. Use the following procedure to remove the date, time, or other information from the opera ti on display area. All items are set to “ON” by de fault. Where necessary, the requi red items can be turned off.
GENERAL SET 4 English 87 2 Turn the jog dial to select “1. DISPLAY SET”, and then turn the shuttle dial clockwise. The <DISPLAY SET> screen is displayed. 3 Turn the shuttle dial clockwise. “ON” for the (1) “DATE” flashe s. This can be set to “OFF” turning the jog dial to remove the date from th e operation display a rea.
GENERAL SET 4 88 English SETTINGS z After “VIDEO LOSS” is detect ed, it can be cancelled by performing eithe r of the following. (1) Input a video signal. (2) If no vi deo input is requi red, use a [CAMERA SELECT] button to select the camera for which video loss was detected an d then press an d hold the same button.
GENERAL SET 4 English 89 Use the procedures described below to se t a passwords and to prevent unauthorized users fr om operating the digi tal video recorder. If a button is pressed while the se curity lock is in opera tion, a buzzer will be sound ed.
GENERAL SET 4 90 English SETTINGS 3 Turn the shuttle dial clockwise. The first password character “-” flashes. 4 Set a character (0 to 9, A to Z) with the jog dial or numeric keys. Example: Display “1” with the jog dial or numeric keys. 5 Turn the shuttle dial clockwise.
GENERAL SET 4 English 91 1 Turn the jog dial to move cursor to “REC CONTROL”. 2 Turn the shuttle dial clockwise. Turn the jog dial to select either “ADMIN” or “USER”, and then turn the shuttle dial clockwise. The cursor moves to “CAMERA CONTROL.
GENERAL SET 4 92 English SETTINGS z If an administrator password w as entered, the security lock is cancelled and the indicator is turned off. z If a user password was entered, the security lock is partially cancelled and the indicator remains lit. This section describes how to initialize and expan d the hard disk.
GENERAL SET 4 English 93 Please contact your local store or service center regarding hard disk expansion. A separately sold hard disk provided by Sanyo will be required in or der to perform this procedur e. [Setting conditions] z Initialization must always be carried out after ha rd disk expansion.
GENERAL SET 4 94 English SETTINGS 1 Press the [MENU] button and turn the jog dial to select “3. GENERAL SET”, and then turn the shuttle dial clockwise. The <GENERAL SET> screen is displayed. 2 Turn the jog dial to selec t “5. NETWORK SET”, and then turn the shuttle dial clockwise.
GENERAL SET 4 English 95 6 Set “IP ADDRESS”. (Default setting: 192. 168. 0. 1) 7 Set “SUBNET MASK”. (Default setting: 255. 255. 255. 0) 8 Set “GATEWAY”. (Default setting: 0. 0. 0. 0) 9 Set “PORT”. (Default setting: 00080) Three access levels are setup for n etwork connection, and a password is set for each.
GENERAL SET 4 96 English SETTINGS 4 Following this, turn the shuttle dial clockwise. 5 Where necessary, use the same procedure to set the “ID2” and “ID3” passwords. 6 When setting has been completed, press the [EXIT/OSD] button. The setting procedure is ended and the display returns to the normal scre en.
GENERAL SET 4 English 97 5 Turn the shuttle dial clockwise and turn the jog dial to set “ALARM INFO”, and then turn the shuttle dial clockwise. The cursor moves to “ADDRESS”.
GENERAL SET 4 98 English SETTINGS 4 Turn the jog dial to select a protocol and then turn the shuttle dial clockwise. The “ADD.” column flashes. [Settings] ( indicates default setting) 5 Set address (1 to 127) with the jog dial or numeric keys and turn the shuttle dial clockwise.
GENERAL SET 4 English 99 1 Press the [FUNC.] button. The FUNC. indi cator lights up a nd camera control mode is activate d. 2 The buttons on the digital video recorder operate the dome cameras as follows. In camera control mode the indicator lights up for all the following.
100 English SETTINGS 5 SCREEN SET Use the following procedure to change the display positions for cameras in quad, multi 9 and 16 screens. z Each camera can o nly be displayed in one position on any screenP. Example: Displaying Ca mera No. 05 in quad po sition 01 On the DSR-3709P, select cameras No.
SCREEN SET 5 English 101 4 Turn the shuttle dial clockwise. The <QUAD POSITION SET> screen is displayed. z When arranging display position for 9 screen display select “MULTI 9 POSITION SET” and for 16 screen display select “MU LTI 16 POSITION.
SCREEN SET 5 102 English SETTINGS Use the following proced ure to scroll through vi deo from all cameras using a specified period. A switching time for automatic selection can only be set for full screen and quad display. Example: Automatic switching of a full screen on the monitor every 5 s econds.
SCREEN SET 5 English 103 3 Turn the jog dial to move the cursor to “MAIN/MON.2 MONITOR SET”, and then turn the shuttle dial clockwise. The <MAIN/MON.2 MONITOR SET> screen is displayed. 4 Turn the shuttle dial clockwise. “T-1” starts to flash for “TIME PERIOD”.
SCREEN SET 5 104 English SETTINGS Use the following p rocedure to set vi deo from a specific camera (including playba ck video) to be masked by a gray pattern when it is not to be shown on a monitor screen. Example: Preventing the d isplay of unneeded c amera video at the set period (as indicated by TIME PERIOD A and TIME PERIOD B).
SCREEN SET 5 English 105 8 Turn the jog dial clockwise or counter- clockwise to move the cursor to channel to be changed. On the DSR-3709P, select cameras No. 1 thro ugh No. 9. 9 Turn the shuttle dial clockwise. “OFF” flashes. [Settings] ( indicates default setting) z Masked channels will not display playback video.
SCREEN SET 5 106 English SETTINGS 3 Press the [CAMERA SELECT] button for the camera whose color level is to be set, and then turn the shuttle dial clockwise. “5” flashes. 4 Turn the jog dial to select a “COLOR LEVEL” (1 through 10), a nd then turn the shuttle dial clockwise.
English 107 6 POWER LOSS/USED TIME Use the following procedure to check the date and time of power losses, the amount of hard disk op eration time, and the amount of power-on time. 1 Press the [MENU] button and turn the select “5. POWER LOSS/USED TIME”, and then turn the shuttle dial clockwise.
108 English SETTINGS 7 INITIALIZATION LOG Use the following procedure to display the eight most recent entries in th e initialization and re-recordi ng log for the hard disk. 1 Press the [MENU] button and turn the jog dial to select “6. INITIALIZATION LOG”, and then turn the shuttle dial clockwise.
English 109 8 COPY MENU SETTINGS Use the following p rocedure to save menu se ttings on a CompactFlash card or to load settings from a CompactFlash card back into the digi tal video recorder. These functions make it easy to use the sa me settings on a number of differe nt hard disk digital recorders.
COPY MENU SETTINGS 8 110 English SETTINGS Use the following procedure to load menu settings saved on a CompactFlash card back into the digital vi deo recorder. z When loading a menu setti ng file into the recorder, you will be able to specify whether recording area settings are to be copied.
English 111 1 INTERFACE SPECIFICATIONS Data format Communication protoco l A proprietary protocol (SANYO protocol) is used. Use of a special controller for operation is recommende d.
INTERFACE SPECIFICATIONS 1 112 English OTHER The table belo w shows the commands suppo rted by the digital video re corder. SANYO protocol command table Left digit Right digit 0 1 2 3 4 5 6 7 0 0 TIME.
English 113 2 SPECIFICATIONS Note that product appearance and specificati ons are subject to change without prior notice. Specifications Product name Digital video recorder with multiple xer function .
SPECIFICATIONS 2 114 English OTHER Units: mm Dimensions CARD CARD MENU RESET EJECT CARD CARD MENU RESET EJECT 420 86 86 420 365 365 DSR-3716P DSR-3709P e00_l8hbg_xe_7.
SPECIFICATIONS 2 English 115 This products’s recording time can be changed by modifying the recording rate and the recording picture quality. The following table provides reference values for p icture quality and recording rate in a situation where video is recorded to the normal recording area of this product’s hard disk.
SPECIFICATIONS 2 116 English OTHER Example: Recording to a 300 GB hard disk (1 00%-usage) Area in which sound recording i s possible (when recordi ng soun d, the record ing time is shorter than that shown above.) Recording ra te FPS (field/sec) Recording ti me BASIC NORMAL ENHANCED FINE S UPER FINE 15kB 22kB 30kB 42kB 50kB 50.
SPECIFICATIONS 2 English 117 Normal recording rate Alarm record ing rate Pre-alarm recording rate (Note 1) 25 FPS maximum when pre- alarm recording is set to “ON”. (Note 2) 25 FPS maximum when recording only one camera; 50 FPS maximum when recording two or more cameras.
SPECIFICATIONS 2 118 English OTHER This table indicate s recording times for pre-alarm recording, an d it should be used whe n this type of recording is be ing carrie d out.
SPECIFICATIONS 2 English 119 Terminal board specifications Input/output terminals Signal level Input/output circuit Alarm input [No-volt contacts] Sensor alarm output [Open collector/1k Ω , Low level active (max: 25mA)] CTL2,3 Remote control input [Two-wire voltage contr ol] ( J P.
SPECIFICATIONS 2 120 English OTHER CTL8 Warning output [DC5V/5.7k Ω , Active Low] CTL9 Normal recording area disk full warning output [DC5V/5.7k Ω , Active Low] CTL10 Alarm recording area disk full warning output [DC5V/5.7k Ω , Active Low] CTL11 Series connection input [DC5V/5.
English 121 3 MENU SETTING SEQUENCE <INITIAL SET> 1.LAUNGUAGE/CLOCK SET -> 2.CAMERA DETECT -> 3.TITLE SET -> 4.HOLIDAY SET -> 5.TIME PERIOD SET -> MOVE:JOG SELECT:SHUTTLE <RECORD SET> 1.NORMAL REC EASY SET -> 2.RECORDING AREA SET -> 3.
MENU SETTING SEQUENCE 3 122 English OTHER <GENERAL SET> 1.DISPLAY SET -> 2.BUZZER SET -> 3.SECURITY LOCK SET -> 4.HDD SET -> 5.NETWORK SET -> 6.RS-485 SET -> 7.CAMERA CONTROL SET -> MOVE:JOG SELECT:SHUTTLE <SCREEN SET> 1.
English 123 INDEX A Administrator .......... .............. ...................... ........... ......... 89 ALARM FULL indicator ........... ........... .............. ................ 7 ALARM indicator ......... ....................... ..............
INDEX 124 English Series recording ............. ....................... .............. ........... 69 Setting alarm recording ............. .............. ....................... 77 Setting camera titles ............... ...................... .......
e00_l8hbg_xe_7.book Page 125 Frid ay, November 5, 2004 10:21 AM.
デバイスSanyo DSR-3709Pの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Sanyo DSR-3709Pをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSanyo DSR-3709Pの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Sanyo DSR-3709Pの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Sanyo DSR-3709Pで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Sanyo DSR-3709Pを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSanyo DSR-3709Pの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Sanyo DSR-3709Pに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSanyo DSR-3709Pデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。