SanyoメーカーICR-B50の使用説明書/サービス説明書
ページ先へ移動 of 37
ICR-B50 INSTRUCTION MANUAL Digital V oice Recorder ENGLISH ESP AÑOL SANYO'S HELP-LINE Call the toll-free number below if you have any difficulties operating this product.
1 Important Information: Notes on clock setting Be sure to set the date and time of the unit ’ s clock before you start using it. (See “ Adjusting the date and time ” in “ BEFORE OPERA TION ” section.
2 WHA T TO DO IF ... If the operation of the unit or display is not nor- mal, 1. Open the battery compartment lid. 2. Remove the batteries. Wait 2 minutes, then reinstall the batteries. 3. Press the reset switch (back of the unit) using a small ball-point pen, etc.
3 1 2 3 4 12 15 13 14 11 6 7 9 10 5 8 16 20 17 18 19 21 CONTROLS 1. Earphone jack (EAR) 2. External microphone jack (MIC) 3. Built-in microphone (MIC) 4. Record button ( m )/Pause 5. Repeat button (REPEA T) 6. Stop button ( n ) - ON/OFF button 7. Play button ( a )/Pause 8.
4 POWER SUPPL Y Batteries 1. Open the battery compartment lid. 2. Install two “ AAA ” batteries. Observe proper polarity . Battery indicator ( ) The line of rectangles is the battery gauge. Black rectangles show the battery condition. : Full, good condition or ( “ LOW BA TT ” appears.
5 BEFORE OPERA TION Earphone Connect an earphone (8 ohms, cord length less than 2 meters (6 feet, 6 inches), not supplied) to the EAR jack. (The speaker is automatically dis- connected.) Note: Be sure to reduce the volume before connecting or disconnecting the earphone.
6 Adjusting the date and time 1. Press the MENU button repeatedly until the date and time display ap- pears. 2. Press the TIME/SET button. The year display blinks. 3. Press the c or d button repeatedly to select the year . 4. Press the TIME/SET button.
7 SELECTING THE MENU MODE 1. Press the MENU button repeatedly to select the desired menu mode. Each time the button is pressed, the display changes as follows: FOLDER v EDIT v AUTO P AUSE v Date and time v V AS v REC v BEEP v ERASE GUARD v 12/24 v Original display returns 2.
8 Date and time (See “ Adjusting the date and time ” .) V AS (V oice activated system): Selecting V AS mode V AS OFF wv V AS ON V AS OFF: T o start and stop recording manually V AS ON: Recording begins when the unit picks up sound, and stops after the sound stops.
9 RECORDING 1 . Press the n button to turn the power on. 2. Set the REC MODE switch (back of the unit) to select the desired recording mode. DIC (Dictating): “ ” appears. CONF (Conference): “ ” appears. LECT (Lecture): “ ” appears. Note: If an external microphone (not supplied) is connected, the recording mode cannot be changed.
10 • If the CUE INDEX button is pressed during re- cording, an index mark is made (INDEX number appears briefly) and recording continues. (Up to 16 index marks, for each file, can be made.
11 Insertion recording T o insert into a file (Previous recorded material will remain.) 1. Select the “ INSERT ” edit mode. “ INSERT ” appears on the display . (See “ SELECTING THE MENU MODE ” .) 2. Locate the desired point during playback, then press the a button to pause.
12 PLA YBACK 1. Set the PLA Y SPEED switch (back of the unit) to SLOW , STD, or F AST . SLOW: Slow-speed playback STD: Standard-speed playback F AST : Fast-speed playback 2. Select the desired folder name. (See “ SELECTING THE MENU MODE ” .) 3. Press the a button.
13 Auto pause When the end of the file is reached during playback, “ AUTO ” and “ P AUSE ” appear in turn. The unit pauses automatically for the preset auto pause time. After the set time elapses, the next file playback begins. Press the a button during auto pause to return to the normal pause mode.
14 Time display Press the TIME/SET button repeatedly during recording, playback and stop mode. The display changes as follows. In recording mode Recording time mode, Current file number/T otal file number , Remain- ing recording time v Current time v Original display returns.
15 ERASING Important Note: Before erasing, make sure that the battery indicator is full. Preparations 1. Press the MENU button to select “ FOLDER ” . 2. Press the TIME/SET button. The folder name blinks. 3. Press the c or d button to select the folder to be erased, then press the TIME/SET button.
16 Partial erasing (A-B erasing) 1. Press the c or d button to select the file number. 2. Press the a button to start playback. 3. Press the a button again to pause at the starting point you want to erase (point A). 4. Press the ERASE button. “ ERASE ST ART ” blinks.
17 VOICE ALARM TIMER 1. Press the n button to turn the power on. 2. Select the sub-menu “ ALARM ” of “ FOLDER ” . (See “ SELECTING THE MENU MODE ” .) “ FOLDER ALARM ” appears. 3. Press the n button to return to the original display mode.
18 PC (Personal Computer) CONNECTION Important Note: Y our PC must run the Windows98 operating system with parallel port. Windows is a registered trademark of Microsoft Corporation. Playing back/Editing a data file recorded with your PC Digital voice recordings can be transferred to the PC for playback or editing.
19 Operation 1. Connect the unit to the PC using the Parallel port Adapter as shown in Fig. 17. 2. Press the n button to turn on the power . 3. Operate your PC.
20 4. Press the REPEA T and CUE INDEX buttons at the same time to select “ ENROLL ” . 5. Operate the PC and start “ ViaV oice ” . (Follow the instruction manual supplied with ViaV oice.) Notes on operating ViaV oice For ViaV oice Millennium: 1) On the desktop of Windows, select [Start] > [Settings] > [Control Panel].
21 6. Speak into the unit to record your voice. Notes on enrolling (Fig. 18) It is important to place the unit in a proper position to achieve maximum recognition precision during the transcription process. • Place the unit 5 to 8 cm (2 to 3 inches) away from your mouth.
22 Important Note: When you attempt to transcribe a data file of the ICR-B50, be sure to enroll by using the ICR-B50. If you enroll data by using the headset supplied with ViaV oice, an extremely low recognition rate results. Note: IBM ViaV oice Millennium must be used.
23 CLEANING THE CABINET Clean the outside of the unit with a clean soft cloth, moistened with lukewarm water . Do not use benzene, thinner or alcohol since they will mar the finish of the surfaces.
24 TROUBLESHOOTING GUIDE SYMPTOM POSSIBLE CAUSE CORRECTIVE ACCTION The unit does not operate. The batteries are discharged or not installed. Insert two new “ AAA ” batteries. “ ” appears. The batteries are discharged. Insert two new “ AAA ” batteries.
25 READ CAREFULLY BEFORE USE!!! USER LICENSE AGREEMENT IMPORTANT! — BY INSTALLING, COPYING, ACCESSING, DOWNLOAD- ING, AND/OR USING THIS THE SOFTWARE, YOU ARE CONSENTING TO BE BOUND BY AND ARE BECOMING A PARTY TO THIS AGREE- MENT AS A LICENSEE.
26 1. Grant of License. Licensor shall grant Licensee a non-exclusive, non- sublicensable, non-transferable license for the use of the Software under the terms and conditions set forth herein: • Sys.
27 purposes or otherwise any and all technical information (the “ Technical Information ” ) provided by Licensee to Licensor, provided, however, that Licensor shall ensure that the identity of the Licensee shall remain undisclosed in the Licensor ’ s use of all such Technical Information.
28 5. DISCLAIMER OF WARRANTY: THE SOFTWARE IS DEEMED ACCEPTED BY LICENSEE UPON IT ’ S USE BY LICENSEE. THE SOFTWARE IS PROVIDED TO LICENSEE AS IS, WITHOUT WARRANTY OF ANY KIND.
29 6. Indemnification: Licensor will not have any liability to Licensee for, and Licensee will defend and hold Licensor harmless against, any claim, expense, judg- ment, liability, or loss (including .
30 Tested To Comply With FCC Standards Declaration of Conformity Model Number : ICR-B50 Trade Name : Sanyo Responsible Party : SANYO FISHER COMPANY Address : 21605 Plummer Street Chatsworth, California 91311 Telephone No. : (818) 998-7322 • This device complies with Part 15 of the FCC Rules.
31 For USA SANYO SERVICE PLUS LIMITTED W ARRANTY DICT A TION PRODUCTS ONL Y OBLIGA TIONS In order to obtain factory warranty service for Sanyo Dictation Products, call the toll-free number below . The unit must be packed in the original carton or a well-padded sturdy carton in order to avoid shipping damage.
32 Subject to the OBLIGA TIONS above and EXCLUSIONS below, SANYO FISHER COMP ANY (SFC) warrants this SANYO Dictation product against defects in materials and workmanship for the periods of LABOR and P ARTS specified below .
33 21605 Plummer Street Chatsworth, CA 9131 1 THE DURA TION OF ANY W ARRANTIES WHICH MA Y BE IMPLIED BY LA W (INCLUDING THE W ARRANTIES OF MERCHANT ABILITY AND FIT - NESS) IS LIMITED T O THE TERM OF THIS W ARRANTY .
34 THE SANYO COMFORT W ARRANTY BUSINESS SYSTEMS - DICT A RECORDERS W ARRANTY APPLICA TION New , unused Sanyo Dicta Recorder products purchased in Canada are warranted against manufacturing defects in materials and workmanship for ONE YEAR for parts and NINETY DA YS for labour , from the date of purchase by the original retail purchaser .
35 ORIGINAL RET AIL PURCHASER’S RESPONSIBILITY Y ou, the original retail purchaser, must present your original, dated bill-of- sale together with this warranty to SANYO Canada Inc. or to an authorized Sanyo Service Depot when you make a claim under this W arranty .
36 SANYO Canada Inc. HOW TO OBT AIN W ARRANTY SER VICE Please contact the Sanyo Authorized Dealer from whom the product was purchased, or contact us directly at: SANYO Canada Inc. 300 Applewood Crescent Concord, Ontario L4K 5C7 (905) 760-9944 1-800-263-2244 http://www .
デバイスSanyo ICR-B50の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Sanyo ICR-B50をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSanyo ICR-B50の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Sanyo ICR-B50の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Sanyo ICR-B50で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Sanyo ICR-B50を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSanyo ICR-B50の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Sanyo ICR-B50に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSanyo ICR-B50デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
