SanyoメーカーVSP-3000の使用説明書/サービス説明書
ページ先へ移動 of 34
INSTR UCTION MANU AL System Controller VSP-3000 About this manual • Before installing and using this unit, please read this man ual carefully . Be sure to keep it handy f or later reference .
Introduction 1 Introduction Precautions ........................................................ 2 Safety Cautions ................................................. 3 Main features ..................................................... 7 Accessories ..
Introduction 2 Precautions For UL Users CA UTION RISK OF ELECTRIC SHOCK DO NO T OPEN CA UTION: T O REDUCE THE RISK OF ELECTRIC SHOCK, DO NO T REMO VE CO VER (OR BACK). NO USER-SER VICEABLE P ARTS INSIDE. REFER SER VICING TO QU ALIFIED SERVICE PERSONNEL.
Introduction 3 W ARNING Never use when unit emits smoke, unusual noises, or un usual smells. Using under these abnormal conditions can cause fires and electric shock. Immediately unplug the AC adapter po wer plug from the outlet, confirm that the smoke stops, and then request repairs from the installer or the purchasing source.
Introduction 4 CA UTION T ranspor t with care Unplug the AC adapter po wer plug from the outlet, confirm that connection cables are disconnected, and transport carefully to avoid dropping the unit or subjecting it to sev ere shoc k. Cautions for care or long-term disuse Unplug the AC adapter po wer plug from the outlet.
Introduction 5 Pro vided A C Adapter W ARNING Use only the pr ovided A C adapter Use the provided A C adapter . Using a different AC adapter can cause fires or electric shoc k, due to differences in po wer cord current capacity . Never touch the A C adapter with wet hands This can cause electric shock.
Introduction 6 Safety Cautions CA UTION Do not connect to other equipment The provided A C adapter and pow er cable are exclusiv ely f or use with this unit. Connecting to other equipment can cause fires or electric shock. P ower cor d Damaging the power cord in the f ollo wing manner can cause fires or electric shock.
Introduction 7 Main features Accessories Y ou can use the joystic k to carry out pan, tilt and zoom operations f or the camera. RS-485 communication cab le can be connected. P assw ord setting is a vailab le. T rademark Brands and product names described in this document are trademarks or registered trademarks of their respective companies .
Preparations 8 ① ④ ⑥ ⑤ ⑧⑨ ② ③ PWR Tx Rx ⑩ ⑦ D VR: Digital video recorder ① Escape/P ower button (ESC/PWR) ESC: This is used to exit from the current oper ating menu and return to the initial screen.
Preparations 9 ① ② ③ ④ ⑤ ① P ower terminal (DC 12 V) Connect the accessory AC adapter to the DC terminal. ② USB mouse port (USB) Connect the accessory USB cable to this por t if using a D VR with a mouse function.
Preparations 10 Connecting to a Sany o camera (Operation: P20) Monitor (sold separately) AC adapter (accessory) 485A 485B SIDE-A Dome camera (sold separately) TRx (+) : A TRx (–) : B A B T x 1 T x 2 T x 3 T R x System controller ■ Connection method 01GB_L8CSE_WA_VSP3000.
Preparations 11 Connecting to a Sany o D VR (Operation: P28) Set the protocol to “SSP” f or all of the cameras being connected. (Protocol setting: P21) A RS-485 B DO NOT CONNECT TO PHONE LINE 1 IN.
Preparations 12 Connection method Connecting to a Sany o D VR with a mouse function (Operation: P29) T Camera (sold separately) Camera (sold separately) Video input terminal D VR with mouse function (.
Preparations 13 Main menu steps Press the SUB MENU/MAIN MENU button. The MAIN MENU screen appears in the menu displa y and y ou are prompted to enter the pass word. No passw ord is set initially , so simply press the ENT button. “1.VER: X.XX” will then be displa yed.
Preparations 14 Menu settings 1 Language setting The only av ailable language f or menus is English. No setting is neccessary . When “ENGLISH” is displayed, press the ENT button or the ESC/PWR b utton to return to the MAIN MENU screen. [ ó ñ MAIN MENU ] 3.
Preparations 15 3 Control ID setting If using more than one system controller , change the addresses for each of them. The addresses can be assigned to a number within the range of 0 to 4. (Default setting: 0) 1 Move the jo ystic k up or down to select “5.
Preparations 16 Menu settings 5 Sleep setting Y ou can set the system controller to tur n off automatically if it is not operated f or a cer tain period of time. When this is done, a mo ving “SLEEP MODE” display will appear in the men u display . (Default setting: OFF) 1 Move the jo ystic k up or down to select “7.
Preparations 17 7 Backlight setting This sets the brightness of the system controller’ s menu displa y screen. (Default setting: OFF) 1 Move the jo ystic k up or down to select “9. BA CKLIGHT”. [ ó ñ MAIN MENU †] 9.BACKLIGHT:OFF 2 Move the jo ystic k to the left or right to set the backlight (Example: A UT O).
Preparations 18 Menu settings 9 D VR link setting The camera images from the D VR which is connected to the system controller switch in line with the camera selection. (Default setting: ON) 1 Move the jo ystic k up or down to select “11. D VR LINK”.
Preparations 19 11 Default setting This returns all settings to the default settings that were in place at the time of shipment from the factory . 1 Move the jo ystic k up or down to select “13. F ACT OR Y SET”, and then move the jo ystic k to the right.
Preparations 20 Camera setup steps While pressing the SHIFT/FUNC. b utton, press the SUB MENU/MAIN MENU button. “CAM SETUP001” will be displa yed in the men u display and y ou will be prompted to enter the pass word. [ CAM SETUP001 ] PASSWORD[ ---- ] [ CAM SETUP001 ] OK [ ñ CAM SETUP001†] 1.
Preparations 21 1 Address setting This selects the camera address. All settings other than this one will be applied to the selected address. (Default setting: 001) 1 Move the jo ystic k up or down to select “1.
Preparations 22 Camera settings 3 Baud rate setting This sets the communication speed. (Default setting: 19.2 Kbps) 1 Move the jo ystic k up or down to select “3. BA UDRA TE”. [ ó ñ CAM SETUP001 ◆ ] 3.BAUDRATE:19.2k 2 Move the jo ystic k to the left or right to select the communication speed.
Preparations 23 5 D VR address and c hannel setting This assigns the D VR address and channel number to the selected camera. For details , ref er to “Camera address number s (default value)” . See page 31. 1 Move the jo ystic k up or down to select “6.
Operation 24 Camera operation buttons Joystic k: When in camera mode and a camera menu is not being displa yed, this can be used to carry out pan, tilt and zoom operations. A UT O P AN ST ART : (P27) When this button is pressed, automatic panning is carried out between the preset panning positions.
Operation 25 FOCUS NEAR: Adjusts the focus to the nearest object. FOCUS F AR: Adjusts the focus to the furthest object. GO PRESET P: The camera will mov e to the preset position which has been recorded. For details , ref er to “Preset position retriev al operation” .
Operation 26 Camera operations A uxiliary function operation T ransmits A UX ON/OFF commands to the selected cameras. F or details, ref er to “List of auxiliary commands for San y o cameras” . (P30) 1 Press the A UX b utton. “A UX ON” will be displa yed.
Operation 27 Retrieving pan, sequence and tour operations recorded in a PTZ camera Y ou can select preset pan, sequence and tour operations so that these operations can be carried out. This operation is limited to the f ollowing camera models which already contain preset operations.
Operation 28 Switching the D VR screen display The only D VR function that can be operated from the system controller is the screen displa y s witching function. The monitor screen can be s witched between multi-screen, quad-screen or single-screen displa y by pressing the f ollo wing buttons .
Operation 29 1 Press the mouse ( ) button. “MOUSE MODE” will be display ed, and y ou can then use the joystic k to mov e the cursor . Camera operations cannot be carried out at this time. SANYO SSP 19.2k MOUSE MODE L button: Left clic k R button: Right clic k 2 Press the mouse button once more.
Others 30 List of auxiliary commands for San y o cameras The commands are e xamples of commands f or the VCC-9500/9600/9700/9800 series. Auxiliary command ON OFF Operation 1 Switch to Color Mode P an/Tilt control 1 Switches a day/night camer a to color mode.
Others 31 Camera address number s (default v alue) Camera address Connected D VR Connected channel No . CAM No . D VR CH CAM No . D VR CH CAM No . D VR CH CAM No .
Others 32 Communication f ormat RS485, RS-422 Keyboar d 29 k eys Joystic k 3-axis jo ystick (pan / tilt / z oom) Control comm unication terminal Tx1, Tx2, Tx3, TRx Protocol SSP , H-SSP , P elco-D USB mouse port Compatible with D VRs with mouse function Communication speed 2400, 4800, 9600, 19200, 38400, 57600 bps Max.
SANY O Electric Co., Ltd. 01GB_L8CSE_WA_VSP3000.indd 33 01GB_L8CSE_WA_VSP3000.indd 33 2008/02/29 13:17:10 2008/02/29 13:17:10.
デバイスSanyo VSP-3000の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Sanyo VSP-3000をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSanyo VSP-3000の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Sanyo VSP-3000の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Sanyo VSP-3000で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Sanyo VSP-3000を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSanyo VSP-3000の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Sanyo VSP-3000に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSanyo VSP-3000デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
