Sceptre TechnologiesメーカーX9C-NagaVの使用説明書/サービス説明書
ページ先へ移動 of 22
X9C-NagaV User ’ s Manual.
i FCC Compliance Statement This device complies with part 15 of t he FCC Rules. Operation is subject to the following two conditions: 1. This device may not caus e harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.
ii The Federal Communications Commission warns that changes or modifications of the unit not expre ssly approved by the party responsible for compliance could void the user ’s authority to operate the equipment.
iii T ABLE OF C ONTENTS TABLE OF CO NTENTS .......................................................................................... III Your New LCD Monitor 1 Unpacking 1 Identifying Components 3 Ad.
1 Rev.1 The LCD Monitor Your New LCD Monitor Your LCD Monitor has been desi gned to be versatile, ergonomic and user-friendly. The LCD Monitor is capable of displaying most standards, from 640x400 VGA to 1280x1024 SXGA.
2 Rev.1 After unpacking your LCD monitor, make sure the following items are included in the box and are in good condition: • LCD monitor • Power Cord • Monitor-T o-PC Analog signal cable 15pin • Monitor-T o-PC DVI signal cable • 1.
3 Rev.1 Identifying Components A. The LCD Monitor — Front View Figure 1-1: The LCD Monitor Front View 1. Pow er-On Indicator This Circular LED indicator green lit when the power is on and orange lit when the LCD monitor is in power-saving mode. 2. Monitor Stand 3.
4 Rev.1 B. "Hot Keys" for Quick Adjustment of Monitor Settings Figure 1-2: "Hot Keys" 1. Volume Adjustment "hot key": Press this + button to allow you to adjust the volume of the LCD Monitor directly 50 2.
5 Rev.1 Adjusting the Tilting Angle The LCD Monitor’s angle settings range from 0 ° to 10 ° . 10 Figure 1-3: Tilting the Monitor 0 to 10.
6 Rev.1 Connecting AC Power and Video Cable Note: Turn off your PC and the LCD monitor before connecting your LCD monitor to the computer. DVI VGA AC-IN AC Outlet (Wall Socket) Computer Power Cord Figure 1-4: The AC Adapter Power Management System This LCD Monitor complies with the VESA DPMS power management proposal.
7 Rev.1 The Display Controls The LCD Monitor’s Control Panel Figure 2-1: The Control Pane l 1. : Enable the OSD Menu button or / Move the cursor to the left (w hen OSD is enabled) 2. : Move the cursor to the Right ( When OSD is enabled) / Auto-adjustment hot key 3.
8 Rev.1 Adjusting the Monitor’s Display OSD Main Menu 1. Pressing the Y button causes the screen below to appear. 2. Use the Y & Z key to select the desired group, then press – or + key to enter into sub-menu 3. Repeat step 2 to select the changed item, then – or + to change the value.
9 Rev.1 Auto Adjust Option The Auto Adjust option lets the monitor determine and select the settings that are most appropriate for your system requirements. Note: it only apply for Analog RGB input Provides you with the current display timing information.
10 Rev.1 Set up the color temperature value User Mode Sets the color temperature to 6500K Sets the color temperature to 9300K Red change Red gain for the color temperature (only valid when color tempe.
11 Rev.1 Adjusts phase tracking to reduce display flicker Moves the whole screen right or left Moves the whole screen up or down Return to the previous Menu OSD Adjustment Restores settings to factory.
12 Rev.1 Set DVI port for PC signal input Return to the previous Menu Exit the OSD screen.
13 Rev.1 Note: 1) No video When the monitor is ON and ther e is no video signal received, the following message will be displayed 2) Signal out of range When the frequency range of the signal is out o.
14 Rev.1 Appendix A TFT LCD Monitor Specifications Item Specification LCD Panel 19" SXGA Control Functions Power Software Power switch with LED indicator (ON/OFF) Main Menu Submenu Information Br.
15 Rev.1 Item Specificaiton Scanning Frequency H/V, Hz 24-80K 50-75 P o w e r Management M e e t s VESA DPMS Power Consumption (ON/OFF, W) 37W/1W Max. Dimensions WxHxD 16.
16 Rev.1 Appendix B Supported Timing Item Standards Resolution Dot Clock (MHz) Vertical Scanning Frequency (Hz) Horizontal Scanning Frequency (kHz) 1 NEC PC98 640x400 21.05 56.42 24.83 2 MAC 13" mode 640x480 30.24 66.67 35.00 3 MAC 16" mode 832x624 57.
17 Rev.1 Appendix C Troubleshooting This LCD monitor comes pre-adjusted with standard VGA timing. Due to output timing differences among various VGA cards, you may init ially experience an unstable or unclear display when a new display mode or new VGA card is selected.
18 Rev.1 4. If the power LED is not lit, check that the AC power connector is securely connected, and verify that the AC adapter LED is lit. If the AC adapter LED is not lit, please contact your dealer for assistance. PROBLEM: The LCD displays “signal out of range” error message 1.
デバイスSceptre Technologies X9C-NagaVの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Sceptre Technologies X9C-NagaVをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSceptre Technologies X9C-NagaVの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Sceptre Technologies X9C-NagaVの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Sceptre Technologies X9C-NagaVで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Sceptre Technologies X9C-NagaVを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSceptre Technologies X9C-NagaVの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Sceptre Technologies X9C-NagaVに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSceptre Technologies X9C-NagaVデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
