AvayaメーカーX330W-2DS1の使用説明書/サービス説明書
ページ先へ移動 of 16
A vaya X330W -2DS1 Access Router Module Quick Start Guide N N o o t t e e : The X330W AN expansion modules can be installed in the following A vaya P330 switches: • P333T , P334T , P332MF , P333R, P333R-LB, P333T -PWR – Embedded S/W version 3.
Important Safety Information Before installing or r emoving any components of a device, or carrying out any maintenance work, you must read the safety information pr ovided. CAUTION: T o avoid damage from static, only hold the W AN Expansion Router Module by the edges.
Unpack the Module Check the package contents for the following: Equipment • One X330W AN Access Router Module. L Connection cables are not supplied. Documentation • A vaya X330W AN Access Router Modules Quick Start Guide (this document). • A vaya X330W AN Access Router Modules Release Notes.
Insert the Module T o insert an X330W AN into an A vaya P330 switch: 1. Remove the blanking plate or other expansion module (if installed). 2. Insert the W AN expansion module gently into the slot, ensuring that the Printed Circuit Board (PCB) is aligned with the guide rails.
4 Connect the Ports Connecting the E1/T1 Ports T o connect a T1/E1 module to a network, use a straight-through RJ-48C-to-RJ-48C cable to connect the E1/T1 port to an RJ-48C wall jack. Connecting the Ethernet Port A UTP Category 5 cable must be connected to the 100Base-TX port, via an RJ45 connector .
5 Configure the Module L Before you can set up the X330W AN module you must power on and set up the A vaya P330 stack as described in the A vaya P330 User ’s Guide. L Before using the X330W AN module you must assign an IP addr ess via the Command Line Interface (CLI) or via a T elnet session to the switch where the X330 is inserted.
L The console interface configured with the interface Console command must be on a differ ent subnet from the r outer interfaces. 6. Use the following commands to set the baud rate, ppp authentication.
Configuring Loopback Interfaces L All CLI commands mentioned in this section are described in the A vaya P330 Reference Guide. T o configure Loopback interfaces: 1. Use the interface loopback <loopback number> command to enter the Interface Loopback mode.
Configuring E1/T1 Interfaces L All CLI commands mentioned in this section are described in the A vaya P330 Reference Guide. T o configure E1/T1 interfaces: 1. Use the show controllers command to check if your controller ’s mode is configured as E1 or T1.
Changing the Primary Management Interface (pmi). L The default pmi is the first interface you define. T o change the pmi: 1. Enter one of the interface contexts as explained before. 2. If there no ip assigned on that interface use the | ip address <ip_ addr>< net- mask> command.
X330WAN Default Settings The default settings for the X330W AN and its ports are determined by its embedded software. These default settings are subject to change. Newer versions of the softwar e for the X330W AN can be downloaded from the A vaya Network Software Download W eb site (http://www .
Run the W eb-Based Manager (optional) L T o configure the A vaya X330W AN you can use the P330 W eb-based Manager in addition to using the CLI. System Requirements Minimum hardwar e and Operating Syst.
L If the network manager has configured the system the plug-in should be installed auto- matically . If the plug-in is not installed automatically , there ar e three ways to install the plug-in manually: • Either install the plug-in fr om the CD as follows: 1.
Documentation and Online Help Refer to the A vaya X330W AN Documentation and Utilities CD for full instructions..
Notes.
Contact Information T o contact A vaya technical support: From the United States: Please call 1-800-237-0016, press 0, then pr ess 73300. From outside the United States: EMEA (Europe, Middle East and Africa). Email: csctechnical@avaya.com AP (Asia Pacific).
デバイスAvaya X330W-2DS1の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Avaya X330W-2DS1をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAvaya X330W-2DS1の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Avaya X330W-2DS1の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Avaya X330W-2DS1で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Avaya X330W-2DS1を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAvaya X330W-2DS1の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Avaya X330W-2DS1に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAvaya X330W-2DS1デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
