SharpメーカーAE-Z48LZの使用説明書/サービス説明書
ページ先へ移動 of 20
AIR-TO-AIR HEA T PUMP OPERA TION MANUAL * Plasmacluster is a trademark of SHARP Corporation. INDOOR UNIT OUTDOOR UNIT A Y -ZP48LZ AE-Z48LZ.
.
1 This manual explains the proper use of your new heat pump. Please read this manual carefully before using the product. This manual should be kept in a safe place for handy reference. IMPORTANT SAFETY INSTRUCTIONS W ARNINGS FOR USE 1 This model should be installed with a fixed power cord to the meter box.
2 P ART NAMES INDOOR UNIT 1 Inlet (Air) 2 Open Panel 3 Air Filter 4 Air purifying fi lter 5 AUX Button 6 Receiver Window 7 V ertical air fl ow Louvre 8 Horizontal air fl ow Louvre 9 Outlet (Air) 0 .
3 REMOTE CONTROL 1 TRANSMITTER 2 DISPLA Y 3 COOL Button 4 DRY Button 5 HEA T Button 6 STOP Button 7 THERMOST A T Button 8 PLASMACLUSTER Button 9 SPOT AIR Button 0 FULL POWER Button q F AN Button w 1.
4 SET CURRENT CLOCK TIME There are two clock modes: 12-hour mode and 24-hour mode. Example: 5 o’clock in the afternoon Clock Display 12-hour mode PM 5:00 24-hour mode 17:00 1 T o set to the 12-hour mode, press the CLOCK button once. T o set to the 24-hour mode, press the CLOCK button twice.
5 The air purifying filters are packed as accessory of this unit. During operation, the fi lters remove dust and tobacco smoke from the air and discharges clean air . 1 T ake out the air fi lters. 1 Open the open panel. 2 Push the air filters up slightly to unlock them.
6 1 Press the COOL, DR Y or HEA T button . : HEA T : COOL : DR Y • The red OPERA TION lamp ( ) on the unit will light. 2 T o change the temperature setting, press the THERMOST A T button. HEA T/COOL MODE • The temperature can be set within the range of 18°C to 32°C.
7 HORIZONT AL AIR FLOW DIRECTION 1 Press the SWING button( ). • The horizontal air fl ow louvres will swing. 2 Press the SWING button( ) again when the horizontal air fl ow louvres are at the desired position. NOTE: • The adjusted position will be memorized and will be automatically set to the same position when operated the next time.
8 SPOT AIR The louvres are adjusted so that air fl ow is delivered to the desired area. 1 Press the SPOT AIR button to select the desired air fl ow direction. NOTE: • If you want the SPOT AIR setting in the FULL POWER mode, press the SPOT AIR button during the FULL POWER operation.
9 The unit works at the maximum power and op- timum louvre direction to quickly cool or warm the room. 1 During operation, press the FULL POWER button. • The remote control will display “ ” and AIR FLOW symbol will get longer . • The temperature display will go off.
10 1 . 2 . 3 . 5h OFF TIMER When the 1 . 2 . 3 . 5h OFF TIMER is set, the unit will automatically turn off after the set time (hours). 1 Press the 1 . 2 . 3 . 5h OFF TIMER button to set the desired time. • The time setting will change as you press the button as follows.
11 TIMER ON 1 Press the TIMER ON ( ) button. 2 The TIMER ON indicator will blink; press the TIME ADV ANCE or REVERSE button to set the desired time. (The time can be set in 10-minute increments.) 3 Press the TIMER SET (SET/C) button. • The orange TIMER lamp ( ) on the unit will light.
12 PLASMACLUSTER OPERA TION Plasmacluster ions released into the room will reduce some airborne mold and viruses. 1 During operation, press the PLASMACLUSTER button. • The remote control will display “ ”. • The blue PLASMACLUSTER lamp on the unit will light up.
13 ADDITIONAL NOTES ON OPERA TION OPERA TING TEMPERA TURE RANGE V ACANCY OPERA TION Heating operation with 10°C set temperature will be performed to protect your home and furniture from frost damage, even when you are out. 1 Press the HEA T button. 2 Press the V ACANCY button.
14 MAINTENANCE AFTER HEA T PUMP SEASON 1 Operate the unit in the SELF CLEAN operation to allow the mechanism to thoroughly dry . 2 Stop the operation and turn off the circuit breaker . 3 Clean the fi lters, then reinstall them. MAINTENANCE BEFORE HEA T PUMP SEASON 1 Make sure that the air fi lters are not dirty .
15 The following conditions do not denote equip- ment malfunctions UNIT DOES NOT OPERA TE The unit will not operate if it is turned on immediately after it is turned off. The unit will not operate immediately after the mode is changed. This is to protect the unit.
16.
17.
18 Printed in Thailand TINSEA629JBRZ 09K- TH 1.
デバイスSharp AE-Z48LZの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Sharp AE-Z48LZをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSharp AE-Z48LZの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Sharp AE-Z48LZの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Sharp AE-Z48LZで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Sharp AE-Z48LZを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSharp AE-Z48LZの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Sharp AE-Z48LZに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSharp AE-Z48LZデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。