SharpメーカーHTSB250の使用説明書/サービス説明書
ページ先へ移動 of 16
ENGLISH MODEL HT -SB250(BK) SOUND BAR SYSTEM OPERA TION MANUAL B arcodesof t http://www.barcodesoft.com Barcode Symbology: Code 93 ; Font Facenam e: Code93 M H r Data To Encode: TINSZA877AWZZ Point Si.
E-1 Special notes W ARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE CO VER (OR B ACK). NO USER-SERVICEABLE P ARTS INSIDE. REFER SER VICING TO QU ALIFIED SERVICE PERSONNEL.
E-2 IMPORT ANT SAFETY INSTRUCTIONS Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if improperly handled. This product has been engineered and manufactured with the highest priority on safety .
E-3 IMPORT ANT SAFETY INSTRUCTIONS (continued) If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructio.
E-4 For U.S. customer only CONSUMER LIMITED WARRANTY SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the "Product"), when ship in its or.
E-5 V olume control ■ The soun d level at a given volum e settin g depend s on unit efficiency , location, and various other factors. It is advisable to avoid exposure to high volume levels, which occurs while turning the unit on with the vol ume control setting up high, or while continually listening at high volumes.
E-6 1 10 9 1 1 14 15 12 1 3 3 2 4 5 7 6 8 Audio Line In 2 Jack ................................. 9 Line In 1 Jacks ....................................
E-7 System preparation Make sure to unplug the AC power cord before installing the unit or changing the position. Select from three installation methods according to the preferred position. Using spikes Nuts (secured on spikes) must be used when installing spikes.
E-8 Fix a wall mount plug into the hole using a hammer, until it is ush with the wall surface. 3 1-1/4” (32 mm) 3/8” (8-9 mm) W all surface S y s t e m p r ep a r a t io n ( c o n t i n u e d ) W all surface Screw the wall mount angle to the wall as shown in the illustration.
E-9 Falling prevention Safety wires (not suppl ied) are usef ul to prevent the unit from falling off the table. Loop the safety wires (not supplied) into each hole as shown and tie the safety wires to the LCD TV stand. Sound bar connections to TVs Caution: Turn off all other equipment before making any connections.
E-10 AC power connection Aft er che cki ng al l the con ne cti ons have bee n mad e correctly , connect the AC power cord to the AC power input jack, then to the AC outlet. Using with the AC/DC adaptor ■ 1 Plug the AC power cord into the AC/DC adaptor .
E-1 1 shall not be exposed to excessive heat such as sunshine, re or the like. Installing the battery incorrectly may cause the unit to malfunction. Notes concerning use: Replace the battery if the operating distance is reduced or if the operation becomes erratic.
E-12 General control (continued) Muting ■ The volume is muted temporarily when pressing the MUTE button on the remote cont rol. Pres s again to restore the volume. Preset sound mode ■ Main unit operation: T o change to a different mode, press the SURROUND button repeatedly until the desired sound mode lights up.
E-13 Symptom Possible cause No sound is heard. Is the input signal (selection) set properly? Is the volume level set to “0”? Is muting activated? ● ● ● Noise is heard during playback. Move the unit away from any computers or mobile phones. ● When a button is pressed, the unit does not respond.
E-14 T roubleshooting chart (continued) Condensation ■ Sudden temperature changes, storage or ope rat ion in an extr eme ly hu mid envir onm ent may cause condensation inside the cabinet or on the transmitter on the remote control. Conden sation can cause the unit to ma lfunc- tion.
E-15 Specications As part of our policy of continuous improvement, SHARP reserves the right to make design and specication changes for product improvement without prior notice. The performance specica- tion gures indicated are nominal values of production unit.
デバイスSharp HTSB250の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Sharp HTSB250をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSharp HTSB250の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Sharp HTSB250の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Sharp HTSB250で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Sharp HTSB250を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSharp HTSB250の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Sharp HTSB250に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSharp HTSB250デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。