ShiroメーカーSD2100の使用説明書/サービス説明書
ページ先へ移動 of 14
• User Manual • SD2100 Digital Enhanced Cordless Communication.
1 Contents What the symb ols me an ................................................................... 1 The Handset and Bas e Unit ............................................................... 2 Setting up your telephone ...........................
2 Press to begin, answ er and end a telephone call. Call button Clear / On-Off /END button The Handset and Base Unit Press to enter menu mode and enter sub- menu.
3 Setting up your telephone Connection and con ditions for use You can connect your SD 2100 to a direct exchange line (DEL), a line connected to a local exchange, with its own phone number; to an exte nsion socket connected to a DEL; or to an extension on an approved compat ible PBX.
4 Installation 1. Choose a suitable site for the handset unit Make sure it is not near to another telephone, nor to other electrical equipment. 2. Plug the mains power lead into the power jack the base unit and plug the telephone line cord into the telephone port.
5 the base unit from the telephone line and the mains socket when there are storms in your area. Damage caused by lightning is not covered by the Guarantee.
6 • While the mouthpiece is muted, you cannot press any number key to send digits down the line; Press Mute key again to get back to the call. Conference Calling You need to register with your fixed line networ k operator for conference calling service.
7 Call Logs You must subscribe to Caller ID service from your service provider to use this feat ure. Call Logs store information relate d to received calls, missed ca lls and dialed calls. The SD2100 can store up to a maximu m of 30 calls, cons isting of 10 re ceived, missed and d ialed calls respectively.
8 3. Press the OK button The display shows the current volume level 4. Press UP/DOWN button to change the volume 5. Press the OK button to confirm the volume level you want Ringer Melody (EXT / INT) You can choose the ringer Melody following the below instruction .
9 6. Press OK button to confirm To delete call barring number 1. Press MENU button then UP/DOWN button until the display shows BASE SET 2. Press the OK button, the display shows PIN? 3. Key in your PIN number 4. Press the OK button, then UP/DOWN button to the location BARRING 5.
10 4. Press the OK button and press UP/DOWN button to change Dial mode as TONE or PULSE dialing To reset base 1. Press MENU button, then UP/DOWN button to the location BASE SET 2. Press the OK button, the display shows PIN? 3. Key in your PIN number and press the OK button, then UP/DOWN button to the location B RESET 4.
11 1. Disconnect the power lead fr om the back of the base unit 2. Press and hold the HANDSET LOCATOR button in the base unit, at the same time connect the power lead into the back of base unit. Release the LOCATOR button after you hear “beep” sound for five times.
12 Troubleshooting Always check first that: • You have followed the steps listed on pa ges to install and set up your SD2100. • All connects are firmly inserted in their sockets. • Mains power is switched on at the socke t. • The handset’s batteries are correctly and se curely installed, and are not run down.
13 The strange noise is caused by interference. Di sconnect the main s power lead from the b ack of the base unit, and then wait for 30 seconds before reconnecting it. There is 'beep' sound while I am on a call. You may be going out of range of the base unit.
デバイスShiro SD2100の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Shiro SD2100をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはShiro SD2100の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Shiro SD2100の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Shiro SD2100で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Shiro SD2100を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はShiro SD2100の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Shiro SD2100に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちShiro SD2100デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。