SiemensメーカーIGWIPS200-1の使用説明書/サービス説明書
ページ先へ移動 of 36
INSTALLATION GUIDE IGWiPS200-1 Rev 3 May 2007 ) ) ) ) ) ) ) ) ) ) ) ( ( ( ( ( ( ( ( ( ( ( ( WiPS-200 Series Wireless Process Solution Frequency Hopping Spread Spectrum Radio Two-Way (Multipoint-to-Poi.
.
IGWiPS200-1 TABLE OF CONTENTS SECTION TITLE PAGE PREFACE ........................................................................................................................ ............................. 2 CONVENTIONS AND SYM BOLS ................
IGWiPS200-1 PREFACE CONVENTIONS AND SYMBOLS The followin g symbols m ay be used in this manual and may appear on the equi pment. The reader should becom e familiar with the symbols and their meaning. Symbols are provided to quickly alert the reader to safety related text.
IGWiPS200-1 • For devices with explosion protection: trai ning, instruction or authorization to work on electrical circ uits for systems that could cause explosions. • Training or instruction according to the safety sta ndard s in the care and use of suitable safe ty equipment.
IGWiPS200-1 INTRODUCTION This publication describes installation of the Siemens Wireless Process Solution (WiPS) 200 Seri es Two-W ay Multipoint- To-Point Radios and I/O Expansio n Modules.
IGWiPS200-1 Each transceiver and each I/O Expansion m odule has bus conn ectors on both sides of its c over: a male connector on one side, a female connector on the other. A transceiver and several I/O Expansio n modules can be physically interconnected by way of th eir bus conn ectors and then snapped onto a sect i on of DIN rail as a single unit.
IGWiPS200-1 PRODUCT SUPPORT When contacting Siemens for support: • Please have co mplete product information at hand: • For hardware, this information is provid ed on the product nameplate (part num ber or model n umber, serial num ber, and/or ve rsion).
IGWiPS200-1 INSTALLATION This section provi des installation proce dures for a WiPS 200 Series wirel ess network. A wireless net work contains a master transcei ver and up to e ight remote (i .e. slave) transcei vers. I/O Expansi on modules pr ovide the network wi th additional analog, digital, and pulse I/O ca pacity.
IGWiPS200-1 DANGER Electrical shock hazard Explosion hazard Will cause death or injury. • Remove power from all wires and termin als before working on equipment. • In a potentially hazardous atmosphe re, remove power from equipment before connecting or disconne cting power, signal, or other circuit.
IGWiPS200-1 Changes or modifications not ex pressly approved by Si emens will void the user’s authority to operate the equipment . This product is intended fo r fixed installation applications .
IGWiPS200-1 ANTENNA CON NECT OR S AND S URGE VOLTAGE PROTECTION Each transceive r has an MCX fem ale antenna connect or. The base 3-1/2" , 1/4-wave whip antenna has a n MCX mal e connector. Opt ional higher ga in antennas an d low-loss co axial cables have type-N connectors.
IGWiPS200-1 Control Room At the contr ol room, there is one master t ransceiver and c omplementi ng I/O: one analog output m odule, and one digital out put modul e.
IGWiPS200-1 A. Analog Output and Digital Output Fault Respon se Selections Three I/O m odules (4-Cha nnel Analog Output Mod ule, 8-Channel Digital Out put Module , and Combi nation Input/Output Module.
IGWiPS200-1 Pulse Output Module (See Figure 18 on page 26) There are two DIP s witches for each channel: switches 1 a n d 2 for channel 1, switche s 3 and 4 for channel 2.
IGWiPS200-1 MOUNTING THE DIN RAIL At each installation site, mount the DIN rail and DIN rail mount modules (e.g. tra nsceiver, I/O modules, powe r supply) in a NEMA enclosure appropriat e for the environment and hazardous ar ea classification. Re fer to Figure 3 for transceive r and I/O m odule dime nsions.
IGWiPS200-1 Each module h as a moveable, sp ring-loaded m ounting li p to assist in m ounting a m odule, sliding a module along the DIN rail, and removing a module from the DIN rail. This lip has a slotted tab so the blade of a small screwdriver can be inserted and the lip levered away from the rail.
IGWiPS200-1 MOUNTING THE 1/4-WAVE WHIP ANTENNA Mount the 3-1/6" (80. 4 mm) high, omnidirect ional whip a ntenna 5 , sh own at right, within 5' (1. 5m) of the transceiver to allow the supplied 6' (2m) cable to easily reach between the antenna and transceiver.
IGWiPS200-1 Electrical Connections – Power and I/O connections are completed through screw actuated compression terminals. Connector bl ocks can be rem oved from a m odule for wiri ng, as shown i n the two fig ures below.
IGWiPS200-1 Transceiver Wiring Examples Five transceive r wiring exam ples are provide d below. Figures 6 , 7, and 8 s how typical transceive r wiring for 2-wire, 3-wire, and 4-wir e current loops. Figures 9 and 10 show two variatio ns on the wiring for a loop powered external analog device.
IGWiPS200-1 Figure 7 Transceiver Wiring, 4-20 mA Curren t Loop with 3-Wire Device May 2007 19.
IGWiPS200-1 Figure 8 Transceiver Wiring, 4-20 mA Curren t Loop with 4-Wire Device May 2007 20.
IGWiPS200-1 Figure 9 Transceiver Wiring, Analog and Digital Outpu ts Figure 10 Transceiver Wiring, Analog Outpu t Wirin g for a Loop Powered Device May 2007 21.
IGWiPS200-1 Transceiver RF Link and Output State Wiring Option s This section de scribes the tran sceiver RF link status relay and t he analog ou tput and di gital output wi ring optio ns.
IGWiPS200-1 Green Faceplate Figure 12 4-Channel Analog Input Module Wiring Yellow Faceplate Figure 13 4-Channel Analog Output Module Wiring May 2007 23.
IGWiPS200-1 Blue Faceplate Figure 14 8-Channel Digital Input Module Wiring Pink Faceplate Figure 15 8-Channel Digital Output Module Wiring May 2007 24.
IGWiPS200-1 Multiple Colors Faceplate Figure 16 Combination Input and Output Module Wiring (One Analog Input, One Analog Output, T wo Digital Inputs, and Two Digital Outputs) May 2007 25.
IGWiPS200-1 Orange Faceplate Figure 17 2-Channel Pulse Input Module Wiring Orange Faceplate Figure 18 2-Channel Pulse Output Module Wiring May 2007 26.
IGWiPS200-1 ASSIGNING AND SETTING I/O MODULE ADDRESSES Module addres ses are 1 through 8, as shown on the m odule faceplates i n Figure 19. T he top row in the f igure shows three I/O modules at a location (for example, at a remote location).
IGWiPS200-1 HAZARD LABEL A label, similar to that shown here, is included in a WiPS shipment. The installer or user should post this label in an appropriate, high ly visible location near the WiPS modules.
IGWiPS200-1 4. Locate the Hop Key (a small circuit bo ard) at the rear edge of th e top circuit board , see the figure below . Unplug the Hop Key and set it aside. Hop Key Location 5. Carefully insert the faceplate/circu it boa rd assembly in its cover until it snaps int o place.
IGWiPS200-1 0.0 1.0 2.0 3.0 4.0 -115 - 110 -10 5 -100 -95 -90 -85 -8 0 -75 Signal S trength (-dBm ) +DC Volts RSSI vs DC Voltage MG0044 6a Figure 21 Received Signal Strength Graph TRANSCEIVER AND I/O EXPANSION MODULE STATUS LED INDICATIONS Power LED Indicates the presence of power to the m odu le.
IGWiPS200-1 PULSE OUTPUT MODULE DIAG NOS TIC LED’S There are 3 dia gnostic LED’s on the pulse out put module: Status LED: On solid when I/ O is functional and flashing if there is a confl ict with anothe r module.
IGWiPS200-1 Digital Input Module Channels ............................................................... 8 Digital Input Voltage Range ................................. 5 to 30 Vac/Vd c, re verse polarity protected Input Impedance ...................
IGWiPS200-1 Combination Input/Output Module Channels ............................................................... 1 an alog input 1 analog output 2 digital inputs 2 digital outputs Channel Isolation .................................................
IGWiPS200-1 WARRANTY (a) Seller warrants that on the date of shipment the goods are of the k ind and quality described herein and are free of non-conform ities in workm anship and m aterial. This wa rranty does n ot apply to go ods delivered by Seller but manufacture d by others.
デバイスSiemens IGWIPS200-1の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Siemens IGWIPS200-1をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSiemens IGWIPS200-1の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Siemens IGWIPS200-1の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Siemens IGWIPS200-1で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Siemens IGWIPS200-1を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSiemens IGWIPS200-1の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Siemens IGWIPS200-1に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSiemens IGWIPS200-1デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
