Simplicityメーカー1600 Seriesの使用説明書/サービス説明書
ページ先へ移動 of 88
Parts Manual Rev. 10/2005 Broadmoor / 1600 / 2600 Series Lawn Tractors & Mower Decks TP 400-4205-01-BM-SMA Mf g . No. Descri p tion 1 8 HP Models 1694629 Broadmoor, 18HP Hydro RMO 1694630 Broadmoo.
.
Table Of Content s Torque Specification Chart ...... ............................ ......................... .......... Inside Back Cover PRODUCT COMPONENTS PAGES Frame & Front Axle Gr oup ...........................................................
Frame & Front Axle Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart. Torq ue to 150 ft. lbs. (202 Nm) Torque to 22-4 0 ft. lbs. (30-5 4 Nm) Torque to 13 f t. lbs. Servic e Ki t 168 6985 Torque to 50-5 7 ft. lbs.
PART NO. DESCRIPTION REF NO QTY. Frame & Front Axle Group Footnote s 1 1930645 7 NUT, Hex Flange Lock, 3/8-16 2 1960035 2 WASHER 3 2860646 1 NUT, Hex Flange, 5/8-11 4 1722212A 1 PLATE, Axle 5 1724.
Steering Group - Manual Steering NOTE: Unless noted otherwise, use the standard hardware torque specification chart. Torque to 36-44 ft. lbs. or 48-60 Nm Steering cap snaps over steering wheel. Use washers as required. Torque to 36-44 ft. lbs. or 48-60 Nm Bearin g mounts be low frame.
PART NO. DESCRIPTION REF NO QTY. Steering Group - Manual Steering Footnote s 1 1722318 1 STEERING WHEEL, Straight, Shaft 2 1722319 1 CAP, Steering Wheel, SMI Logo 2 1725024 1 CAP, Steering Wheel, Plai.
Engine & Electric Clutch Group - 16HP & 18HP B riggs & Stratton, Vanguard NOTE: Unless noted otherwise, use the standard hardware torque specification chart. Engine Manufactur er Ga sket & Ha rdw are, Torque to 18 ft. l bs. (25 N m) Tie clutch wir e to keep away from pu lley.
PART NO. DESCRIPTION REF NO QTY. Engine & Electric Clutch Group - 16HP & 18HP B riggs & Stratton, Vanguard Footnote s 1 1723165 1 HOSE, Oil Drain, 10-1/2" Long, 3/8-18 Fittings 2 * 1 .
Engine & Electric Clutch Group - 18HP & 20HP B riggs & Stratton, Vanguard NOTE: Unless noted otherwise, use the standard hardware torque specification chart. Engine Manufactur er Ga sket & Ha rdw are, Torque to 18 ft. l bs. (25 N m) Tie clutch wir e to keep away from pu lley.
PART NO. DESCRIPTION REF NO QTY. Engine & Electric Clutch Group - 18HP & 20HP B riggs & Stratton, Vanguard Footnote s 1 1723165 1 HOSE, Oil Drain, 10-1/2" Long, 3/8-18 Fittings 2 * 1 .
Engine Group - 18HP Kohler NOTE: Unless noted otherwise, use the standard hardware torque specification chart. Eng ine Manufact urer Gas ket & H ard war e, Torque to 18 ft. lb s. (25 Nm) Tie clutch w ire to keep away from pulley. Torque to 45-50 ft.
PART NO. DESCRIPTION REF NO QTY. Engine Group - 18HP Kohler Footnote s 1 1721704 1 MUFFLER 2 * 1 GASKET 3 * 2 LOCKWASHER, 5/16 4 * 2 CAPSCRE W, Socket Head, 5/16 -18 x 7/8, G8 5 1723165 1 HOSE, Oil Dr.
Transmission Group - Tuff Torq K-57 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. Spring to be compressed to 2-1/2 inches with brak e locked .
PART NO. DESCRIPTION REF NO QTY. Transmission Group - Tuff Torq K-57 Footnote s 1 1960676 2 SCREW, Pan Head Torx Taptite, 1/4-20 x 1-1/4, Black 2 1722345 1 PAD, Footrest, LH, without Differential Lock.
Transmi ssion SERVICE PA RTS - Tuff Torq K-57A NOTE: Unless noted otherwise, use the standard hardware torque specification chart. SE AL KI T ( Inc lu d e s Re f.
PART NO. DESCRIPTION REF NO QTY. Transmi ssion SERVICE PA RTS - Tuff Torq K-57A Footnote s 2 1724951 1 HOUSING ASSEMBLY, UPPER 3 1724938 1 HOUSING, LOWER 7 1718052 1 VENT VALVE 15 8 1724279 2 MAGNET, .
Transmi ssion SERVICE PA RTS - Tuff Torq K-57A NOTE: Unless noted otherwise, use the standard hardware torque specification chart. SE AL KI T ( Inc lu d e s Re f.
PART NO. DESCRIPTION REF NO QTY. Transmi ssion SERVICE PA RTS - Tuff Torq K-57A Footnote s 54 1724348 1 PLATE, JERK 55 1708689 1 WASHER 56 1724349 1 PIN, COT TER 57 1724296 1 PIN, SPRING 59 1707879 2 PACKING 58 1718100 1 PIN 6.
Controls Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 11 17 19 12 18 14 13 20 21 27 29 22 28 23 25 4 30 31 37 35 30 32 38 34 36 33 1 5 9 2 8 4 6 3 10 1 6 10 16 24 24 26 15 35 41 40 39 18 7 8 5 986599 The above parts group applies to the following Mfg.
PART NO. DESCRIPTION REF NO QTY. Controls Group Footnote s 1 1721353 1 ROD, Brake Lock 2 1721891 1 KNOB, Push On, Red Plastic "P" 3 1930591 1 CAPSCREW, Hex Flange Whiz Lock, 5/16-18 x 3/4 4 .
Cruise Control Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart. Control Ar m from tr ansmission group. Brake ar m at idle r pivot. Hol e "A" Hook into hole "A" of frame. Install rounded edge of washer toward l ever & bracket assembly .
PART NO. DESCRIPTION REF NO QTY. Cruise Control Group Footnote s 1 1723713 1 DECAL, Cruise & Lift 2 1960666 1 SCREW, Torque Head Plus Socket Head, 1/4-20 x 7/8 3 1722303 1 KNOB, Cruise 4 1920397 1.
Electrical Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart. To Engine Sta rter Headlight Switc h DASH MOUNTED HOOD MOU NTE D UNDER HOO D UNDER HOOD UNDER S EAT.
PART NO. DESCRIPTION REF NO QTY. Electrical Group Footnote s 1 1721810 1 HEADLIGHT ASSEMBLY, 4 Bulb, (Includes Ref. Nos. 2 & 3) 2 1677371 4 BULB, Headlight, 12.8V 3 1723451 4 SOCKET ASSEMBLY, Headlight, Sealed 4 1722669 1 HARNESS, Headlight 5 1722887 1 SWITCH, PTO Push/Pull Symbols 6 1726556 1 MODULE, RMO (Includes Ref.
Hood, Grille & Dash Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 10 12 11 13 17 9 1 5 7 8 4 6 3 9 4 4 2 15 16 14 986608 The above parts group applies to the following Mfg. Nos.: 2005 26 © Copyright Simplicity Manufacturing, Inc.
PART NO. DESCRIPTION REF NO QTY. Hood, Grille & Dash Group Footnote s 1 1721804C 1 PANEL, RH Side 1 1721804D 1 PANEL, RH Side, Red 2 1721801C 1 HOOD, no Louvers 2 1721801D 1 HOOD, no Louvers, Red .
Seat & Seat Deck Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart. Torque to 14-19 in. lbs. (19 - 25.8 Nm) Torque to 25-30 in.
PART NO. DESCRIPTION REF NO QTY. Seat & Seat Deck Group Footnote s 1 1722129A 1 BRACKET, 1-5/8 x 1-3/4 2 1722307 1 * SEAT, 18" Back, Optional 2 1722306 1 * SEAT, 15" Back, Standard 3 172.
Lift Group - Manual Lift NOTE: Unless noted otherwise, use the standard hardware torque specification chart. Install into left ha nd side of lower da sh. 4 5 3 6 1 9 2 8 10 13 14 11 18 17 16 5 12 5 7 15 986412 The above parts group applies to the following Mfg.
PART NO. DESCRIPTION REF NO QTY. Lift Group - Manual Lift Footnote s 1 1722302 1 GRIP, Black Vinyl 2 1722024A 1 ROD, Lift Lever with Flats 3 1930645 1 NUT, Hex Flange Lock, 3/8-16 4 1924940 1 WASHER 5.
Lift Group - Manual Lift NOTE: Unless noted otherwise, use the standard hardware torque specification chart. Insta ll into le ft hand side of lower dash. No te : Mo d e ls with out Cruise 4 5 3 6 1 10 2 8 11 18 19 12 21 17 16 5 13 7 14 9 15 4 5 20 986780 The above parts group applies to the following Mfg.
PART NO. DESCRIPTION REF NO QTY. Lift Group - Manual Lift Footnote s 1 1722302 1 GRIP, Black Vinyl 2 1722024A 1 ROD, Lift Lever with Flats 3 1930645 1 NUT, Hex Flange Lock, 3/8-16 4 1924940 1 WASHER 5.
Wheels & Tires Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart. Fron t Wheels Rear Wheel s Use as requi red. Use as req uire d. 11 4 4 9 2 10 3 5 8 12 10 7 1 14 15 16 17 6 13 18 8 19 6 12 W986614 The above parts group applies to the following Mfg.
PART NO. DESCRIPTION REF NO QTY. Wheels & Tires Group Footnote s 1 1722065 2 WHEEL & TIRE ASSEMBLY, Front, (Includes Ref. Nos. 2, 3, 4, 5, & 6) 2 1722838 1 TIRE, 15 x 6, Super Turf 3 1664090 1 TUBE, Tire, Front, 4.
Decals - Brand & Model NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 6 1 2 2 3 4 5 7 8 10 9 B986614 The above parts group applies to the following Mfg. Nos.: 2005 36 © Copyright Simplicity Manufacturing, Inc.
PART NO. DESCRIPTION REF NO QTY. Decals - Brand & Model Footnote s 1 1717692 1 DECAL, ICON Simplicity, Orange 2 1722551 3 DECAL, Simplicity, Silver & Blue w/Icon 3 1722776 1 DECAL, Broadmoor, .
Decals - Safe ty & Co mmon NOTE: Unless noted otherwise, use the standard hardware torque specification chart. DANGER OPER ATIN G ON SLO PES CAN BE DANGEROUS SEE OPERATOR'S MANUAL. IF YOU CANNOT BA CK-UP A HILL,DO NOT DRI VE ON IT . ROTATING BLADES CU T OFF ARMS AND LEGS RMO™ Syste m: STOP MOWER WHE N CHILDREN ARE N EAR.
PART NO. DESCRIPTION REF NO QTY. Decals - Safe ty & Co mmon Footnote s 1 1722806 1 DECAL, Ignition Switch Symbols, White/Black 2 1718025 1 DECAL, Automatic Control Traction 3 1722779 DECAL, 18HP 3.
38" Mower Deck - Belt , Idler Arm & Hitch NOTE: Unless noted otherwise, use the standard hardware torque specification chart. Insert Must Face Out M oun t H i tc h A ss em b l y an d Leveli ng Adju stment R od using upper set of ho les Hook Spring to Belt Guide Hook Spring {Ref 22 } here when assembled.
PART NO. DESCRIPTION REF NO QTY. 38" Mower Deck - Belt , Idler Arm & Hitch Footnote s 1 1723025 1 V-BELT 2 1928957 2 CAPSCREW, Hex Head, 3/8-16 x 2-3/4 3 1677135A 1 GUARD, Belt 4 1922755 4 WASHER, Plain, 3/8 5 1716553 1 SPACER 6 1685150 1 PULLEY (Includes Ref.
38" Mower Deck - Height Adjustment & Roller Bar NOTE: Unless noted otherwise, use the standard hardware torque specification chart. GREASE Insert Must Face Out Insert Must Face Out GREASE Ins.
PART NO. DESCRIPTION REF NO QTY. 38" Mower Deck - Height Adjustment & Roller Bar Footnote s 1 1930644 2 NUT, Hex Flange Lock, 1/2-13 2 1686686 1 SHAFT & BAR ASSEMBLY (Includes Ref.
38" Mower Deck - Height Adjustment & Roller Bar NOTE: Unless noted otherwise, use the standard hardware torque specification chart. GREASE Insert Must Face Out Insert Must Face Out GREASE Ins.
PART NO. DESCRIPTION REF NO QTY. 38" Mower Deck - Height Adjustment & Roller Bar Footnote s 45 1704093 1 ROD, Adjustment 46 1706644 1 SPACER 47 1722036 2 ROLLER The above parts group applies to the following Mfg. Nos.: 2005 45 © Copyright Simplicity Manufacturing, Inc.
38" Mower Deck - Housin g, Arbors & Blades NOTE: Unless noted otherwise, use the standard hardware torque specification chart. Viewed From Bottom Torque to 50-70 ft. lbs. Torque to 45-55 ft. lbs. Apply gasket former to this surface if foam gasket is not used.
PART NO. DESCRIPTION REF NO QTY. 38" Mower Deck - Housin g, Arbors & Blades Footnote s 1 1705449 1 DEFLECTOR, Plastic 2 1960518 1 NUT, Push 3 1960353 2 WASHER, Plain 4 1704873 1 CLAMP 5 19169.
40" Mower Deck - Belt , Idler Arm & Hitch NOTE: Unless noted otherwise, use the standard hardware torque specification chart. To Slot "A" To Slot "B" Slot "B" Sl.
PART NO. DESCRIPTION REF NO QTY. 40" Mower Deck - Belt , Idler Arm & Hitch Footnote s 1 1919439 1 NUT, Hex Lock Esna Light, 3/8-16 2 1924940 6 WASHER, 3/8 3 1725408 1 PULLEY, Idler 4 1723391 .
40" Mower Deck - Height Adjustment & Roller Bar NOTE: Unless noted otherwise, use the standard hardware torque specification chart. Apply Locktite 380 in hole prior to assemb ly.
PART NO. DESCRIPTION REF NO QTY. 40" Mower Deck - Height Adjustment & Roller Bar Footnote s 1 1722661 1 ROD 2 1924940 8 WASHER, 3/8 3 1922606 1 CAPSCREW, Hex Head, 3/8-16 x 1 3/4 4 1917421 1 .
40" Mower Deck - Height Adjustment & Roller Bar NOTE: Unless noted otherwise, use the standard hardware torque specification chart. Apply Locktite 380 in hole prior to assemb ly.
PART NO. DESCRIPTION REF NO QTY. 40" Mower Deck - Height Adjustment & Roller Bar Footnote s 45 1720919 1 DECAL, Height of Cut 46 1720931A 1 BRACKET, Height of Cut 47 1930651 1 NUT, Hex Center.
40" Mower Deck - Housin g, Arbors & Blades NOTE: Unless noted otherwise, use the standard hardware torque specification chart. Torque to 45-55 ft.
PART NO. DESCRIPTION REF NO QTY. 40" Mower Deck - Housin g, Arbors & Blades Footnote s 1 1930584 1 CAPSCREW, Hex Head, 7/16-14 x 2-3/4 G8 2 1933263 1 WASHER, 7/16 3 1656916 3 WASHER, Spring 4.
40" Mower Deck - Housin g, Arbors & Blades NOTE: Unless noted otherwise, use the standard hardware torque specification chart. Torque to 45-55 ft.
PART NO. DESCRIPTION REF NO QTY. 40" Mower Deck - Housin g, Arbors & Blades Footnote s 44 1721132A 1 GUARD, Extension 45 1675044 4 RIVIT, Pop 46 1960096 4 WASHER, 3/16 x 3/4 x 1/16 47 1713675 2 WASHER, Bellville 48 1726825 1 ARBOR SHAFT & BEARING ASSEMBLY The above parts group applies to the following Mfg.
44" Mower Deck - Belt , Idler Arm & Hitch NOTE: Unless noted otherwise, use the standard hardware torque specification chart. Engine Pulley Movable Idler Pulley Arbor Drive Pulley Arbor Drive.
PART NO. DESCRIPTION REF NO QTY. 44" Mower Deck - Belt , Idler Arm & Hitch Footnote s 1 1601672 1 V-BELT, Mower Drive 2 1721532 1 V-BELT, Arbor Drive 3 1665835 1 GRIP, Lever 4 1916950 2 NUT, .
44" Mower Deck - Height Adjustment & Roller Bar NOTE: Unless noted otherwise, use the standard hardware torque specification chart. Insert Must Face Out Insert Must Face Out GREASE Feet tow a.
PART NO. DESCRIPTION REF NO QTY. 44" Mower Deck - Height Adjustment & Roller Bar Footnote s 1 1685443 1 SHAFT & BAR ASSEMBLY, 44" (Includes Ref.
44" Mower Deck - Height Adjustment & Roller Bar NOTE: Unless noted otherwise, use the standard hardware torque specification chart. Insert Must Face Out Insert Must Face Out GREASE Feet tow a.
PART NO. DESCRIPTION REF NO QTY. 44" Mower Deck - Height Adjustment & Roller Bar Footnote s 45 1704087 1 TRUNNION, Threaded 46 1719901 1 CRANK, Height of Cut 47 1714084 1 KNOB, Height Crank 48 1960093 1 PAL NUT The above parts group applies to the following Mfg.
44" Mower Deck - Housin g, Arbors & Blades NOTE: Unless noted otherwise, use the standard hardware torque specification chart. Torque nuts to 50-70 ft. lbs. (67-95 Nm.) Torque screws to 45-55 ft. lbs. (61-75 Nm) Apply gasket former to this surface if foam gasket is not used.
PART NO. DESCRIPTION REF NO QTY. 44" Mower Deck - Housin g, Arbors & Blades Footnote s 1 1714419 3 NUT, Hex Flange, 9/16-18 2 1713675 6 WASHER, Bellevilled, 9/16 3 1713161 1 PULLEY, 4-1/2 O.D. 4 1713158 1 HUB, Double Pulley 5 1713098 3 PULLEY, 4-1/4 O.
44" Mower Deck - Housin g, Arbors & Blades CE NOTE: Unless noted otherwise, use the standard hardware torque specification chart. Torque nuts to 5 0-70 ft. lb s. (67-95 Nm.) Torque sc rews to 45-55 ft. lb s. (61- 75 Nm) Apply gaske t former to this su rface if foam ga sket is no t used .
PART NO. DESCRIPTION REF NO QTY. 44" Mower Deck - Housin g, Arbors & Blades CE Footnote s 1 1714419 3 NUT, Hex Flange, 9/16-18 2 1713675 6 WASHER, Bellevilled, 9/16 3 1713161 1 PULLEY 4 17131.
44" Mower Deck - Housin g, Arbors & Blades CE NOTE: Unless noted otherwise, use the standard hardware torque specification chart. Torque nuts to 5 0-70 ft. lb s. (67-95 Nm.) Torque sc rews to 45-55 ft. lb s. (61- 75 Nm) Apply gaske t former to this su rface if foam ga sket is no t used .
PART NO. DESCRIPTION REF NO QTY. 44" Mower Deck - Housin g, Arbors & Blades CE Footnote s 44 1716878A 1 BAFFLE, Anti-Blowout, RH (CE Only) The above parts group applies to the following Mfg. Nos.: 2005 69 © Copyright Simplicity Manufacturing, Inc.
50" Mower Deck - Cl ut ch & Support NOTE: Unless noted otherwise, use the standard hardware torque specification chart. Engine Pul ley Movable Idler Pul ley Arbor Drive Pul ley Arbor Drive Pu.
PART NO. DESCRIPTION REF NO QTY. 50" Mower Deck - Cl ut ch & Support Footnote s 1 1707740 1 V-BELT, Mower Drive 2 1703836 1 V-BELT, Arbor Drive 3 1665835 1 GRIP, Lever 4 1916950 2 NUT, Hex, 3.
50" Mower Deck - Height Adjustment & Roller Bar NOTE: Unless noted otherwise, use the standard hardware torque specification chart. Insert Must Face Out Insert Must Face Out Mount H itch Asse.
PART NO. DESCRIPTION REF NO QTY. 50" Mower Deck - Height Adjustment & Roller Bar Footnote s 1 1686687 1 SHAFT ASSEMBLY, Roller, 50", (Includes Ref.
50" Mower Deck - Height Adjustment & Roller Bar NOTE: Unless noted otherwise, use the standard hardware torque specification chart. Insert Must Face Out Insert Must Face Out Mount H itch Asse.
PART NO. DESCRIPTION REF NO QTY. 50" Mower Deck - Height Adjustment & Roller Bar Footnote s 45 1960093 1 PAL NUT The above parts group applies to the following Mfg. Nos.: 2005 75 © Copyright Simplicity Manufacturing, Inc. All Rights Reserved.
50" Mower Deck - Height Adjustment & Roller Bar NOTE: Unless noted otherwise, use the standard hardware torque specification chart. Insert Must Face Out Mount Hitch Assembly and • Leveling .
PART NO. DESCRIPTION REF NO QTY. 50" Mower Deck - Height Adjustment & Roller Bar Footnote s 1 1719901 1 CRANK, Cutting Height 2 1714084 1 KNOB, Height Crank 3 1960093 1 PAL NUT 4 1924366 8 WA.
50" Mower Deck - Height Adjustment & Roller Bar NOTE: Unless noted otherwise, use the standard hardware torque specification chart. Insert Must Face Out Mount Hitch Assembly and • Leveling .
PART NO. DESCRIPTION REF NO QTY. 50" Mower Deck - Height Adjustment & Roller Bar Footnote s 45 1704116A 1 BRACKET, Cutting Height 46 1704083A 1 ARM, Rear, Mower, RH 47 1921977 2 CAPSCREW, Hex Head, 5/16-18 x 1-1/4 48 1704087 1 TRUNNION, Threaded The above parts group applies to the following Mfg.
50" Mower Deck - Housin g, Arbors & Blades NOTE: Unless noted otherwise, use the standard hardware torque specification chart. Torque nuts to 50-70 ft. lbs. (67-95 Nm.) Torque s crews to 45-55 ft. lbs. (61-75 Nm) Apply gasket former to this surface if foam gasket is not used.
PART NO. DESCRIPTION REF NO QTY. 50" Mower Deck - Housin g, Arbors & Blades Footnote s 1 1714419 3 NUT, Hex Flange, 9/16-18 2 1713675 6 WASHER, Bellevilled, 9/16 3 1713161 1 PULLEY 4 1713158 .
50" Mower Deck - Housin g, Arbors & Blades NOTE: Unless noted otherwise, use the standard hardware torque specification chart. Torque nuts to 50-70 ft. lbs. (67-95 Nm.) Torque s crews to 45-55 ft. lbs. (61-75 Nm) Apply gasket former to this surface if foam gasket is not used.
PART NO. DESCRIPTION REF NO QTY. 50" Mower Deck - Housin g, Arbors & Blades Footnote s 1 1714419 3 NUT, Hex Flange, 9/16-18 2 1713675 6 WASHER, Bellevilled, 9/16 3 1713161 1 PULLEY 4 1713158 .
50" Mower Deck - Housin g, Arbors & Blades NOTE: Unless noted otherwise, use the standard hardware torque specification chart. Torque nuts to 50-70 ft. lbs. (67-95 Nm.) Torque s crews to 45-55 ft. lbs. (61-75 Nm) Apply gasket former to this surface if foam gasket is not used.
PART NO. DESCRIPTION REF NO QTY. 50" Mower Deck - Housin g, Arbors & Blades Footnote s 44 1927557 2 NUT, Hex, Whizlock, 5 /16-18 45 1931333 2 CARRIAGE BOLT, 5/16-18 x 3/4 The above parts group applies to the following Mfg. Nos.: 2005 85 © Copyright Simplicity Manufacturing, Inc.
.
T or que Specification Char t FOR ST ANDARD MACHINE HARDWARE (T olerance ± 20%) Hardware Grade SAE Grade 2 SAE Grade 5 SAE Grade 8 Size Of in/lbs in/lbs in/lbs Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm. 8-32 19 2.1 30 3.4 41 4.6 8-36 20 2.3 31 3.5 43 4.
500 N. Spring Street / PO Box 997 Port Washington, WI 53074-0997 USA www.simplicitymfg.c om MANUFACTURING, INC. © Copyright Simplicity Manufacturing, Inc.
デバイスSimplicity 1600 Seriesの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Simplicity 1600 Seriesをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSimplicity 1600 Seriesの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Simplicity 1600 Seriesの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Simplicity 1600 Seriesで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Simplicity 1600 Seriesを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSimplicity 1600 Seriesの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Simplicity 1600 Seriesに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSimplicity 1600 Seriesデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。