Simplicityメーカー1693651 860Mの使用説明書/サービス説明書
ページ先へ移動 of 26
How to use this file...(Operators Manuals) ————————————————————————————————————————————––– Instructions for Print Vendors (Paper Manuals) Paper Size: * 11 x 17 * Body—50 lbs brilliant white offset or equivalent.
THIS PAGE INTENTIONALLY BLANK.
OPERA T OR’S MANU AL Lar g e Frame Sno wthr o wer 860M LargeFrame Snowthr ower Mfg. No. Description 1693650 860M, 8HP Snowthrower 1693651 860M, 8HP Snowthrower (Export) 1693763 860M, 8HP Snowthrower.
MANUFACTURING, INC. 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 www.simplicitymfg.com © Copyright 2000, Simplicity Manufacturing, Inc.
1 T able Of Contents SAFETY RULES General ...................................................................2 Preparation .............................................................2 Operation .......................................................
03 2 W ARNING This unit is a “two-stage” snowthrower. The first stage is the auger, which feeds the snow back into the impeller housing. The second stage is the impeller, which throws the snow out the dis- charge chute. If bodily contact is made with the auger or impeller when they are rotating, severe personal injury will occur.
03 3 Safety Rules OPERA TION • Keep hands and feet away from rotating parts. Keep clear of discharge opening at all times. • Always clear snow up and down the face of slopes, never across the face. Use extreme caution when changing direction on slopes.
03 Safety Decals 4 SAFETY DECALS Safety warning decals are placed at strategic locations on the snowthrower as a constant reminder to the opera- tor of the most important safety precautions. All warning, caution and instructional messages on your snowthrow- er should be carefully read and obeyed.
03 5 Controls Figure 1. Snowthrower Controls Figure 2. Engine Controls ENGINE CONTR OLS SNO WTHR O WER CONTROLS A Electric Start Button (Optional) Activates electric starter B Fuel Valve Turns fuel supply on or off. C Starter Handle Used to start engine D Primer Button Primes carburetor for faster cold starting.
03 6 ST AR TING CONTROLS Electric Start Units Only A. Electric Start Button - The Electric Start Button (A, Figure 3) activates an electric starter mounted to the engine, eliminating the need to pull the starter handle.
03 7 Controls Figure 4. Operator's Control Position A. Speed Selector C. Auger Control B. Drive Control D. Chute Direction Control Figure 5. Snowthrower Controls A. Speed Selector F. Chute Deflector Knob (Behind) B. Drive Control G. Skid Shoes C.
03 8 GENERAL OPERA TION CHECKS BEFORE EA CH ST AR T -UP 1. Make sure all safety guards are in place and all nuts, bolts and clips are secure. 2. Check the engine oil level. See your engine Owner ’ s Manual for procedure and specifications. 3. Check to make sure spark plug wire is attached and spark plug is tightened securely.
03 9 Operation ST AR TING THE ENGINE 1. Turn the fuel valve (B, Figure 6) to the ON position. 2. Insert the Engine Key (F) into the Engine Key slot and push fully in to the RUN position. 3. Move the Throttle Lever (E) fully up to the FAST posi- tion. 4.
03 10 GR OUND SPEED SELECT OR Use the Speed Selector (A, Figure 8) to control the drive speed of the snowthrower. There are five forward speeds and two reverse speeds. Use the lower speeds to blow deep or wet snow. Use the higher speeds to blow light snow or to drive the snow- thrower without blowing snow.
03 11 Operation FREE-WHEELING AND TRA CTION DRIVE LOCK For easy turning when pushing the snowthrower, you can disengage the traction drive at one or both wheels by using the Traction Lock Pins (See Figures 11 & 12.) 1. Turn the unit off, remove the Engine Key, and discon- nect the spark plug wire.
03 12 Regular Maintenance NORMAL CARE OFF-SEASON ST ORA GE Before you store your snowthrower for the off-season, read the Maintenance and Storage instructions in the Safety Rules section and take the .
Figure 18. Lubricate Deflector Hinges 04 LUBRICATION NOTES: 1.Grease locations indicated by grease gun symbol: Use grease fittings when present. Disassemble parts to apply grease to moving parts when grease fittings are not installed. 2.Oil locations indicated by oil can symbol: Do not allow oil to drip onto traction drive or friction disc.
03 14 T roubleshooting, Adjustments, & Service W ARNING Before performing any adjustment or service to snowthrower, stop the engine and wait for moving parts to stop. Remove the key. To prevent accidental starting, disconnect the spark plug wire and fasten away from the plug.
03 15 T roubleshooting, Adjustments, & Service PROBLEM POSSIBLE CA USE REMED Y Auger rotates, but snow is not thrown far enough 1. Chute Deflector too low. 2. Engine speed too slow. 3. Ground speed too fast. 4. Snowthrower discharge chute clogged.
03 16 T roubleshooting, Adjustments, & Service TRA CTION DRIVE SYSTEM ADJUSTMENT Speed Selector Piv ot Adjustment The Speed Selector is factory set for optimal perfor- mance at each forward and reverse speed setting. However, if drive system components have been replaced, adjustment may be necessary.
T roubleshooting, Adjustments, & Service 17 03 A UGER DRIVE SYSTEM ADJUSTMENTS A uger Drive Clutch Rod Adjustment All auger drive adjustment is accomplished through the auger drive clutch rod. The rod must be adjusted so that there is 1/32 ” clearance between the spring hook and the auger lever (see Figure 21).
T roubleshooting, Adjustments, & Service 18 03 Figure 24. Belts and Pulleys A. Capscrews F. Auger Pulley B. Belt Guides G. Idler Pulley, Auger C. Traction Drive Belt H. Traction Pulley D. Auger Drive Belt I. Idler Pulley, Traction E. Engine Pulley Figure 23.
03 T roubleshooting, Adjustments, & Service 19 Figure 25. Belt Pattern (as viewed from front of snowthrower) A. Engine Pulley C. Idler Pulley B. Drive Belt D. Driven Pulley Figure 26. Shear Pins SHEAR PIN REPLA CEMENT Under most circumstances, if the auger strikes an object which could cause damage to the unit, the shear pin will break.
03 DISCHARGE CONTR OL ADJUSTMENT If the discharge chute is difficult to operate, first lubricate the pinion gear (A, Figure 27) and ring gear (F). If it is still difficult to operate, adjust as follows: 1. Loosen the nut (G, Figure 27) which holds the pinion gear bracket in the slotted hole.
Specifications 21 03 ENGINE Make ................................................................Tecumseh Cylinders ........................................................................1 Cycles ......................................................
03 22 USE ONL Y GENUINE SIMPLICITY REPLA CEMENT P ARTS A vailable thr ough your local authorized SIMPLICITY dealer . Specifications Note: Information listed above is correct at time of printing, and are subject to changes in availability and specifications without notice.
デバイスSimplicity 1693651 860Mの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Simplicity 1693651 860Mをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSimplicity 1693651 860Mの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Simplicity 1693651 860Mの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Simplicity 1693651 860Mで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Simplicity 1693651 860Mを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSimplicity 1693651 860Mの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Simplicity 1693651 860Mに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSimplicity 1693651 860Mデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。