Simplicityメーカー520M, 520Eの使用説明書/サービス説明書
ページ先へ移動 of 20
OPERA T OR’S MANU AL Single Sta g e Sno wthr o wer 520M Models Mfg. No. Description 1694585 520M, 5HP Snowthrower, Manual Start 7085663 SS5201R, 5HP Snowthrower, Manual Start 520E Models Mfg. No. Description 1694586 520E, 5HP Snowthrower, Electric Start 7085664 SS5201E, 5HP Snowthrower, Electric Start Manual No 7100194 I.
1 T able of Contents Safety Rules & Information Training ...................................................................2 Preparation .............................................................2 Operation ....................................
2 This machine is capable to amputating hands and feet and throwing objects. Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment.
3 8. Always follow the engine manual instructions for stor- age preparations before storing the unit for both short and long term periods. 9. Always follow the engine manual instructions for proper start-up procedures when returning the unit to service.
4 Product Identification ID Tag When contacting your authorized dealer for replace- ment parts, service, or information you MUST have these numbers. Record your model name/number, manufacturer’s identi- fication numbers, and engine serial numbers in the space provided for easy access.
5 Safety Rules & Information SAFETY DECALS Safety warning decals are placed at strategic locations on the snowthrower as a constant reminder to the opera- tor of the most important safety precautions. All warning, caution and instructional messages on your snowthrow- er should be carefully read and obeyed.
6 Safety Rules & Information International Symbols F AST SLOW STOP CHOKE PRIMER ELECTRIC ST ART IGNITION KEY RUN.
7 Assembling the Snowthrower T OOLS REQUIRED • Socket or Wrench Set • Pair of Pliers ASSEMBL Y PR OCEDURE If your unit was not previously assembled, see Figures 1 and 2, and follow the steps below to assemble the unit: 1. Install the discharge chute on to the rotating ring located on the auger housing.
8 Controls & Operation Auger Control Chute Direction Control Chute Deflector Clean-Out Tool A B C D Engages auger when pulled back, and disengages auger when released. Rotates discharge chute to desired direction Controls vertical angle snow is thrown.
9 Controls & Operation ENGINE & ST AR TING CONTR OLS NOTE: Throttle - This snow thrower does NOT have a throttle for controlling operating speed of engine. The engine governor maintains operating speed for vary- ing snow removal conditions. Electric Star t Units Only A.
10 GENERAL OPERA TION CHECKS BEFORE EA CH ST AR T -UP 1. Make sure all safety guards are in place and all nuts, bolts and clips are secure. 2. Check the fuel supply. Fill the tank no closer than 1/4 to 1/2 inch of top of tank to provide space for expan- sion.
11 FUEL AND OIL MIXTURE The snowthrower uses a two cycle engine that requires a mixture of fuel (gasoline) and oil for lubrication of engine bearings and other moving parts. The correct fuel/oil mixture ratio is 50 to 1. Use fuel/oil mixture chart shown.
12 Controls & Operation ST AR TING THE ENGINE NOTE: The snowthrower engine is designed to operate at cold temperatures. Avoid operating the snowthrower if air temperature is 40° C or warmer since engine may vapor lock and stop running after a short time.
13 OPERA TING THE SNO WTHRO WER Before operating snowthrower, review the Checks Before Each Use under General Operation on page 8 of this manual. 1. Rotate the discharge chute to the desired direction. 2. Pull the Auger Control back against the handle to engage the auger.
Figure 11. Grease the Discharge Chute Ring Lubricate Flange Regular Maintenance 14 Remo ving Belt Co ver In order to perform proper lubrication, it is necessary to remove the Belt cover from the lower left of the snowthrower. 1. Remove the Engine Key from the switch.
TR OUBLESHOO TING Problem Possible Cause Remedy Engine fails to start 1. Key is OFF 1. Turn Key to the ON position 2. Failure to prime cold engine 2. Press primer button twice and restart. 3. Out of fuel 3. Fill fuel tank 4. Choke OFF - cold engine 4.
16 T roubleshooting & Service Adjusting the Cable 1. Remove the engine cover. 2. Locate and loosen the lower locknut securing the auger control cable (shown in Figure 14). 3. To change the slack in the cable, turn the upper lock- nut slightly just until the slack between the spring and the exposed cable has been eliminated.
17 T roubleshooting & Service REPLA CING THE DRIVE BEL T 1. Remove engine key from switch. 2. Remove belt and engine covers. 3. Move the auger control on the handle and slip the belt out from between the brake lever and roller and away from the idler pulley.
18 ENGINE: 5 HP* T ecumseh Make Tecumseh Model HSK 850 Horsepower* 5 @ 4000 rpm Displacement 8.46 Cu. in (139 cc) Oil Mixture 50:1 CHASSIS: Spout Rotation 220 Depress Auger Diameter 9” (22.
MANUFACTURING, INC. 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 www.simplicitymfg.com © Copyright 2005, Simplicity Manufacturing, Inc.
デバイスSimplicity 520M, 520Eの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Simplicity 520M, 520Eをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSimplicity 520M, 520Eの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Simplicity 520M, 520Eの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Simplicity 520M, 520Eで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Simplicity 520M, 520Eを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSimplicity 520M, 520Eの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Simplicity 520M, 520Eに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSimplicity 520M, 520Eデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。