Simplicityメーカー522Eの使用説明書/サービス説明書
ページ先へ移動 of 28
Print V endor Instructions Ho w to use this file Operator’ s Manuals P aper Size: • 11x17 • Body - 50 lbs brilliant white offset or equivalent. • Cov er - on pre-printed two tone “Sw ash” stoc k.
THIS P A GE INTENTIONALL Y BLANK (FOR PLA CEMENT ONL Y - DO NO T PRINT).
OPERA T OR’S MANU AL Single Sta g e Sno wthr o wer 522E Models Mfg. No. Description 1695468 522E, Snowthrower 1695514 522E, Snowthrower (CE) 1742166-00 Rev 7/2008 TP 100-4961-00-SW-S.
.
1 T able of Contents CONTENTS: Safety Rules & Inf ormation General ...................................................................2 Training ...................................................................4 Preparation .....................
2 Operating Safety Congratulations on purchasing a superior-quality piece of lawn and garden equipment. Our products are designed and manu- factured to meet or exceed all industry standards for safety.
3 Moving Parts This equipment has many moving parts that can injure you or someone else. However, if you are standing in the operator’s position, and follow all the rules in this book, the unit is safe to operate. The auger and impeller have spinning parts that can amputate hands and feet.
4 This machine is capable to amputating hands and feet and throwing objects. Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment.
5 8. Always follow the engine manual instructions for stor- age preparations before storing the unit for both short and long term periods. 9. Always follow the engine manual instructions for proper start-up procedures when returning the unit to service.
6 Product Identification ID Tag When contacting your authorized dealer for replace- ment parts, service, or information you MUST have these numbers. Record your model name/number, manufacturer’s identi- fication numbers, and engine serial numbers in the space provided for easy access.
7 Product Identification SAFETY DECALS Safety warning decals are placed at strategic locations on the snowthrower as a constant reminder to the opera- tor of the most important safety precautions. All warning, caution and instructional messages on your snowthrow- er should be carefully read and obeyed.
8 T OOLS REQUIRED • Knife REMO V AL FROM CAR T ON 1. Locate and remove container of oil. 2. Locate all parts packed separately and remove from carton. NOTE: Set the fuel stabilizer aside until adding gasoline to the fuel tank. We recommend that fuel stabilizer be added to the fuel each time that gasoline is added to the fuel tank.
9 2. Attach the auger drive cable (C, Figure 3) to the auger drive lever (A) using the Z-hook (B). 3. Remove the T-knob (B, Figure 4) and bolt on the upper chute. 4. Rotate the upper chute (A) to the operating position (past the lower chute stop) 5. Install the bolt and tighten the T-knob (B).
10 Controls & Operation Auger Control Chute Direction Control Chute Deflector A B C Engages auger when pulled back, and disengages auger when released. Rotates discharge chute to desired direction. Controls vertical angle snow is thrown. Figure 7 .
11 Controls & Operation ENGINE & ST ARTING CONTR OLS NOTE: This snow thrower does NOT have a throttle for controlling operating speed of engine.
12 GENERAL OPERA TION CHECKS BEFORE EA CH ST ART -UP 1. Make sure all safety guards are in place and all nuts, bolts and clips are secure. 2. Check the fuel supply. Fill the tank no closer than 1/4 to 1/2 inch of top of tank to provide space for expan- sion.
13 ADDING ENGINE OIL 1. Make sure the unit is level. Use a high quality deter- gent oil classified “For Service SG, SH, SJ, SL, or higher”. 2. Remove the oil fill cap/dipstick access panel (A, Figure 9). 2. Remove the oil fill cap/dipstick (B) and wipe with a clean cloth.
14 Controls & Operation ST ARTING THE ENGINE NOTE: The snowthrower engine is designed to operate at cold temperatures. Avoid operating the snowthrower if air temperature is 40° For warmer since engine may vapor lock and stop running after a short time.
15 Controls & Operation OPERA TING THE SNO WTHR O WER Before operating snowthrower, review the Checks Before Each Use under General Operation on page 12 of this manual. 1. Rotate the discharge chute to the desired direction. 2. Pull the Auger Control back against the handle to engage the auger.
Regular Maintenance 16 Before beginning any repair stop the engine, remove the key, disconnect the spark plug wire, and wait for all moving parts to stop.
17 T roubleshooting & Service Figure 12. Chute Removal and Installation A. Chute B. Fasteners A B B B B CHUTE REMO V AL AND INST ALLA TION 1. Remove the fasteners (B, Figure 12) that secure the chute (A) to the top cover. 2. Remove the chute (A). 3.
18 A C C C B B C A B B C C E D Figure 13. Top Cover and Belt Cover A. Screw, 1/4-20 x 5/8 B. Screw, #10-24 x 1/2 C. Screw, 1/4-14 x 3/4 D. Top Cover E. Belt Cover CO VER REMO V AL AND INST ALLA TION To access the drive system or the engine, the covers must be removed as follows: REMOVE THE TOP COVER 1.
REPLA CE DRIVE BEL T The drive belt is of special construction and must be replaced with original factory replacement belt available from your nearest dealer. 1. Remove the belt cover. See “Remove The Belt Cover”. 2. Remove the drive belt (E, Figure 14) from the idler pulley (G).
20 SER VICING THE SP ARK PLUG 1. Remove engine key from switch. 2. Remove the oil access cover. 3. Disconnect the wire from the spark plug. 4. Inspect the spark plug and clean. If necessary, replace it with a new spark plug as recommended in the engine Owner’s Manual.
A UGER DRIVE CABLE ADJUSTMENT The auger drive cable is adjusted at the factory and no adjustment should be necessary. If the cable becomes stretched or is sagging, adjustment will be necessary. Whenever the belt is adjusted or replaced, the cable will need to be adjusted.
22 ENGINE: 5.25 Series Briggs & Stratton Make Briggs & Stratton Domestic Model / Type 09A413 / 0202E1 CE Model / Type 09A413 / 0203E1 Gross Torque* 5.25 ft. lbs. @ 3060 rpm Displacement 9.02 Cu. in (148 cc) CHASSIS: Spout Rotation 190 Degrees Auger Diameter 9” (22.
.
Briggs & Stratton Power Products Group, L.L.C. Copyright © 2008 Briggs & Stratton Corporation Milwaukee, WI USA. All Rights Reserved www.BRIGGSandSTRATTON.
デバイスSimplicity 522Eの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Simplicity 522Eをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSimplicity 522Eの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Simplicity 522Eの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Simplicity 522Eで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Simplicity 522Eを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSimplicity 522Eの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Simplicity 522Eに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSimplicity 522Eデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。