Smart Technologiesメーカー3000iの使用説明書/サービス説明書
ページ先へ移動 of 18
99-00360-02 Rev A0 Room Control Module Installation Guide for the Interactive Whiteboard.
FCC Warning This equipment has been tested and found to comp ly wi th the limits for a Class A digita l device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operat ed in a commercial env ironment.
99-00360-02 REV A0 Contents Contents Installing the Room Control Module ................................................ 1 About the Custom Straight-Through MOD4 I 2 C Cabl es................................. 1 Removing the Bl ank P anel .............
.
99-00360-02 REV A0 Room Control Module Installation Guide for the 3000i 1 Installing the Room Control Module These instructions explain how to install the SM ART Room Control Module (part No.
2 Room Control Module Installation Guide for the 3000i 99-00360-02 REV A0 Removing the Blank Panel NOTE : We recommend that you wear the suppli ed anti-static wrist strap throughout the installation process. This wrist strap protects electronic components from damage due to electrostatic discharge.
99-00360-02 REV A0 Room Control Module Installation Guide for the 3000i 3 Completing the Computer 2 (X-Port 20) Serial Panel Connections 1 Disconnect the computer 2 serial cabl e from the computer 2 serial panel. Comput er 2 Seri al Cable R e a r o f C a b i n e t 2 Remove the four screws used to attach the computer 2 serial panel.
4 Room Control Module Installation Guide for the 3000i 99-00360-02 REV A0 4 Disconnect the MOD4 I 2 C cable at the top of the computer 2 serial panel. MOD4 I C Cable R e a r o f C a b i n e t 2 5 Run this cable behind the patch panel and through the opening where the blank panel was removed.
99-00360-02 REV A0 Room Control Module Installation Guide for the 3000i 5 7 Tilt the computer 2 serial panel and pull it outsi de the cabinet. As you pull the panel out, flip it so the RJ11-6 (RJ12) connectors remain insi de the cabinet. The front of the panel should face you.
6 Room Control Module Installation Guide for the 3000i 99-00360-02 REV A0 2 Bundle any excess cable, fasten it with the supplied tie wrap, and clip off any excess tie-wrap length. Room C o ntrol Module Tie Wrap R e a r o f C a b i n e t T h i s d e v i c e c o m p l i e s w i t h p a r t 1 5 o f t h e F C C r u l e s .
99-00360-02 REV A0 Room Control Module Installation Guide for the 3000i 7 Updating the Control Panel Firmware The procedure for updating the control panel firmwa re varies depending on the last four digits of the serial number on your 3000i.
8 Room Control Module Installation Guide for the 3000i 99-00360-02 REV A0 2 Reach inside the cabinet, behind the front panel. Lift the serial-controller metal housing up and then back to release it from the keyholes on the panel. 3 Carefully lower the serial controller through the opening in the front panel.
99-00360-02 REV A0 Room Control Module Installation Guide for the 3000i 9 6 Reach inside the cabinet and attach the serial controller metal housing to the inside of the front panel. To do this, fit the two partially inserted screws on the metal housing into the keyholes on the front panel.
10 Room Control Module Installation Guide for the 3000i 99-00360-02 REV A0 3 Carefully lower the serial controller through the opening in the front panel. The cables should remain connected to the serial controller. You’ll notice that the I 2 C control panel flash cable is bundled with the DB9 serial cable.
99-00360-02 REV A0 Room Control Module Installation Guide for the 3000i 11 2 Connect the DB9F end of a DB9F/custom cable to the Control port on the Room Control Module. This cable isn’t supplied by SMART Te chnologies. It’s usually supplied by the third- party room control vendor.
12 Room Control Module Installation Guide for the 3000i 99-00360-02 REV A0 2 Open the WBDiag application as follows: a On the Boards tab, click the Log button. The Status Log opens. b Click the Diagnostics button. The WBDiag application opens. 3 Open the port in WBDiag as follows: a There are four numbered COM port buttons on the WBDiag toolbar.
99-00360-02 REV A0 Room Control Module Installation Guide for the 3000i 13 3 Browse to the hex file and open it. The download process takes approximately 20 to 30 minutes. We recommend that you not disturb th is process by performing any work on the laptop or internal computer for the duration of the download.
14 Room Control Module Installation Guide for the 3000i 99-00360-02 REV A0 Customer Support SMART’s Technical Support team welcomes your call. However, you may want to contact your local reseller first if you experience problems with any SMART product.
デバイスSmart Technologies 3000iの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Smart Technologies 3000iをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSmart Technologies 3000iの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Smart Technologies 3000iの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Smart Technologies 3000iで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Smart Technologies 3000iを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSmart Technologies 3000iの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Smart Technologies 3000iに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSmart Technologies 3000iデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
