Smart TechnologiesメーカーSBFPDの使用説明書/サービス説明書
ページ先へ移動 of 46
Interactive Whiteboar d Installation Guide TM SMAR T Board.
FCC W arning This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
99-00667-00 B0 Important Inform ation i Import ant Information Please read this manual carefully before setting up and using the SMART Board™ for Flat-Panel Displays interactive whiteboard (SBFPD). W ARNING Mak e sure an AC so cket outlet is near the SBFPD and remain s easily accessible during u se.
ii Important Inform ation 99-00667-00 B0 A VERTISSEMENT POUR LES CLIENT S EUROPÉENS Le SBFPD doit être utilisé uniquement avec les systèmes de distribution d’aliment ation européens TN et TT . Le SBFPD ne convient p as aux systèmes de distribution d’aliment ation plus anciens de type IP utilisés dans certains p ays européens.
99-00667-00 B0 Important Inform ation iii Other Precautions For operating safety a nd to avoid damage to the interactive whiteboard an d its par ts, please read the following information carefully . • If you transport the interactive whiteboard, we strongly urge you to co mpletely repackage it using the original p ackaging.
iv Important Inform ation 99-00667-00 B0.
99-00667-00 B0 Table of Co ntents v T a ble of Content s Import ant Information i Other Precautions ............... ............. ................ ............. ................ ............. ............. ........... ............ . iii Introduction 1 Interactive Whiteboard T echnology .
vi Table of Co ntents 99-00667-00 B0.
99-00667-00 B0 Introduction 1 Introduction The SMART Board for Fla t-Panel Displays interactive whiteboard adds touch-screen contr ol and writing capability to your flat-panel display while only minimally increasing its depth.
2 Introduction 99-00667-00 B0 The overlay , which includes embedded digit al camera s in the top-left an d top-right corners, is mounted onto your flat-p anel display . The pen tray att aches to your overlay and includ es four colored pens and an eraser .
99-00667-00 B0 Introduction 3 • Floating T ools – a virtua l pale tte of writing tools that increases the screen’ s interactive functionality , even if you do n’t have a p en tray • SMART Bo.
4 Introduction 99-00667-00 B0 Import ant Information about Comp atibility Each SMART Board for Flat-Panel Displays in teractive whiteboard comes with a SMAR T USB adapter cable that connects the interactive whitebo ard to your computer . The adapter cable works only with version 8.
99-00667-00 B0 Installing SMART Board Software 5 Inst alling SMART Board Sof tware For the SMAR T Board for Flat-Panel Displays inte ractive whiteboard to function pr operly , you must have SMART Boar d software running on a connected computer . The following procedures guide you through the process of installing SMART B oard soft ware.
6 Installing SMART Board Software 99-00667 -00 B0.
99-00667-00 B0 Installing the Inte ractive Whiteboard 7 Inst alling the Interactive Whiteboard T o install your SMART Board for Flat-Panel Displays interactive whiteboa rd, you’ll have to: 1. mount th e overlay on the flat-panel dis play (see be low) 2.
8 Installing the Inte ractive Whiteboard 99-006 67-00 B0 2. With the assistance of ano ther person, carefully remove the flat- panel display from the wall mount or the st and, and place it face down on a flat surface. NOTE: The appearance of your flat-p anel display and its a dapter plate can vary from the diagrams shown in this section.
99-00667-00 B0 Installing the Inte ractive Whiteboard 9 5. Place the mo unting brack et’s center section on a flat su rface with th e arrows poin ting upwards and the text “Install Lef t Hanger Here” on your lef t.
10 Installing the Inte ractive Whiteboard 99-006 67-00 B0 7. Attach the second hange r bracket in the same way . 8. Place the mou nting bracket ov er the flat-panel displa y with the left hang er bracket on your right side. The left bracket goe s on your right because you are looking at the back of the flat-panel disp lay .
99-00667-00 B0 Installing the Inte ractive Whiteboard 11 10. Add a supplied washer to each of the exposed adapter plate bolt holes. Don’t add washer s to the two holes covered by the mounting bracket. The washers compensa te for the mounting bracket’s thickness.
12 Installing the Inte ractive Whiteboard 99-006 67-00 B0 12. Loosen the T-handles on the hang er brackets. Push these bracket s towards the flat surface and then tighten the T-hand les. 13. With the assistance of ano ther person, mount the flat-panel display onto a wall mount or onto a stand.
99-00667-00 B0 Installing the Inte ractive Whiteboard 13 16. Place the overlay facedown on a flat su rface. 17. Attach a washer and an ad justment handle to the overlay’ s two mounting plates, leaving approximately 1/4" ( 0.6 cm) of space be tween the washer and the moun ting plate.
14 Installing the Inte ractive Whiteboard 99-006 67-00 B0 18. With the assistance of a nother person, mount th e overlay onto the flat-p anel display by sliding the adjustment handles into the U-shaped slots in the hanger bracket s. NOTE: The adjustment handle and the washer must slide behin d the hanger brackets .
99-00667-00 B0 Installing the Inte ractive Whiteboard 15 19. With the assistance of ano ther person, and while supporting the over lay , loosen both adjustment handles, vert ically adjust the overlay so that you can see most of the flat-panel display’s screen, and then tight en the handles.
16 Installing the Inte ractive Whiteboard 99-006 67-00 B0 21. With the assistance of ano ther person, and while supporting the over lay , loosen both adjustment handles, vert ically adjust the overlay so that you can see all of the flat-panel display’ s screen, and then tighten the handles.
99-00667-00 B0 Installing the Inte ractive Whiteboard 17 NOTE: Depending upon where an d how the interact ive whiteboard is mo unted, you may need to perform the following steps by touch due to reduced visibility . 1. Remove the thumbscrews from the pen tray bracket.
18 Installing the Inte ractive Whiteboard 99-006 67-00 B0 4. Connect the MOD8 cable to th e pen tray (see the next illustra tion). Y ou’ll connect the other end of this cab le to your computer when you complete the inst allation. 5. Connect the DB9 end of the SMART USB adapter cable to the pen tray .
99-00667-00 B0 Installing the Inte ractive Whiteboard 19 If you purchased the SMAR T Board for Flat-Panel Displays interactive whiteboa rd witho ut the pen tray , you must insta ll a controller unit.
20 Installing the Inte ractive Whiteboard 99-006 67-00 B0 4. Connect the MOD8 cable to the co ntroller . 5. Connect the DB9 end of the SMART USB adapter cable to the controller . Y ou’ll connect the other end of this cable to your computer when you complete the in stallation.
99-00667-00 B0 Installing the Inte ractive Whiteboard 21 1. Connect th e MOD8 cable to the correspo nding po rt on the back of the overlay . Y ou connected the other end of this cable to either the pen tray or the co ntroller earlier . 2. Connect the power supply conn ector to the overlay’s power port.
22 Installing the Inte ractive Whiteboard 99-006 67-00 B0 3. Connect the power cable to both th e power supply and a power outlet. 4. Connect the SMAR T USB adapter cable to a USB port on your computer . Y ou connected the other end of this cable to either the pe n tray or the controller earlier .
99-00667-00 B0 Installing the Inte ractive Whiteboard 23 6. Attach the eraser’s retaining wall and pla ce the eraser in its slot. 7. Place the four pens in the appropriate locations.
24 Installing the Inte ractive Whiteboard 99-006 67-00 B0.
99-00667-00 B0 Preparing the Inte ractive Whiteboard for Use 25 Prep aring the Interactive Whiteboard for Use When you’ve insta lled SMART Board sof tware (page 5), set up your SMART Board for Flat-Panel Displays interactive whiteboard and connected it to the computer (page 7), the interactive whiteboard still isn’t quite ready to use.
26 Preparing the Inte ractive Whiteboard for Use 99- 00667-00 B0 1. Press th e SMART Board icon in the system tray (Windows computers) or in the Dock (Macintosh computers), and p ress Orient . The orient ation screen appears. 2. Follow the on-scree n instructions, pressing your finger squar ely on each target.
99-00667-00 B0 Preparing the Inte ractive Whiteboard for Use 27 4. If you know to which port you connec ted the interactive whiteboard, select Manually choo se COM port . The Select COM Port dialog box appears. Highlight the correct port from the list, and press Select .
28 Preparing the Inte ractive Whiteboard for Use 99- 00667-00 B0 1. If you haven’t already done so, connect the flat-p anel display to your computer . (See the previous procedure.) 2. Press th e SMART Board icon in the system tray and press Control Panel .
99-00667-00 B0 Preparing the Inte ractive Whiteboard for Use 29 1. Connect a serial cable from the flat-p anel display to an available serial port on you r computer . NOTE: Y ou may already have connected the flat-p anel display to t he computer to activate the On-Screen Display Control (page 28).
30 Preparing the Inte ractive Whiteboard for Use 99- 00667-00 B0 The t able below summarizes the fun ction of each icon in the strip. If you find you no longer need the Display Control icon strip, yo u can easily disable and remove it (page 30). 1. Connect the flat-p anel display to a serial port on your computer (page 21).
99-00667-00 B0 Cleaning and Troubleshootin g 31 Cleaning and T roubleshooting Cleaning Shut down your computer before you clean the inte ractive whiteboard.
32 Cleaning and Troubleshootin g 99-00667-00 B0 If you encounter a problem with the intera ctive whiteb oard, check all the cable connections. If this doesn’t solve the problem, note the color of th e LEDs described above and cont act SMART T echnical Su pport (page 33).
99-00667-00 B0 Customer Suppor t 33 Customer Support Online Support www .smarttech.com/support Visit the SMAR T T echnologies support site to view and download user’s guides, “how-to” and troubleshooting ar ticles, software and more. T raining Vis it www .
34 Customer Suppor t 99-00667-00 B0 Registration T o help us serve you, register online at www .smarttech.com/registration . Sending Feedback Y ou can help us improve our technical documentation by e-mailing your comments to Documenta tion@smarttech.com.
99-00667-00 B0 Index 35 Index A Activating the SMART Bulb Saver 29 B Bad Orientation Point 26 Bracket 7 Bulb Saver see SMART Bulb Saver C Calibrating the Cameras 32 Cleaning 31 Completing the Install .
36 Index 99-006 67-00 B0 Overlay Introduction 2 Mounting 7 P Pen Tray Installing 16 Introduction 2 Preparing the Interactive Whiteboa rd for use 25 Q Quick Orientation 25 R Recorder 2 Removing the Dis.
.
99-00667-00 REV B0 SMART T echnologies 1207 – 1 1 A venue SW , Suite 300 Calgary , AB T3C 0M5 CANADA www .smarttech.com/support www .smarttech.com/contactsupport Support +1.
デバイスSmart Technologies SBFPDの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Smart Technologies SBFPDをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSmart Technologies SBFPDの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Smart Technologies SBFPDの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Smart Technologies SBFPDで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Smart Technologies SBFPDを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSmart Technologies SBFPDの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Smart Technologies SBFPDに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSmart Technologies SBFPDデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
