Snapperメーカー1691525の使用説明書/サービス説明書
ページ先へ移動 of 16
OPERATOR’S MANUAL Table of Contents ,.MOWER DRIVEN VACUUM COLLECTOR 36” BLOWER ASSEMBLY MFG. NO. 1691356 42” & 48” BLOWER ASSEMBLY MFG. NO. 1691260 CART COLLECTOR MFG. NO. 1691525 DECALS SAFETY RULES - p. 2 INSTALLATION - BLOWER ASSEMBLY, 36” MOWER - p.
Safety Rules Read these safety rules and the safety rules in your Operator’s Manual and follow them closely. Failure to obey these rules could result in loss of control of vehicle, severe personal injury to yourself, or damage to property or equipment.
INSTALLATION - BLOWER ASSEMBLY, 36” MOWER I. Remove the mower deflector by rerpoving two carriage bolts, lockwashers and nuts. Save this hardware for use when blower is removed for side discharge. 2. Install strap (A, figure I) as follows: a. Drill a 9132” hole for large spacer (B).
6. Install wing nut (G, figure I) assembly as follows. Insert 5/ 16-18 x2-1/2&p&w and 5/ i6flat washer from inside the deck. Place the cup (H) onto the capscrew and install S/ 16 lockwasher and 5/ 16 nut. (Figure 12 shows correct position ofcup.
INSTALLATION - BLOWER ASSEMBLY, 42” & 48” MOWER 1. Remove the right-hand arbor cover (A, figure 7) by 4. Before installing arbor bracket (9, figure X), remove removing bolts, washers and nuts in front that hold washer from underneath blade brake bracket (rear cover to deck.
7. Install new arbor pulley(D, figure 8) with hubdown. Use new 7/ 16-14 x 2-l/4 capscrew and washers removed in step 2. Torque to 55 to 60 ft. Ibs. Use wood block to prevent blade from turning. It may be necessary to add washer(s) (two provided) under- neath the new pulley to properly align brake pad and bottom groove.
Figure 11. A. Blower Housing B. Arbor Cover C. Hook D. Clip E. Capscrew F. Washer, 5/l 6 G. Washer. 5/l 6 H. Spacer I. Lockwasher, 5/l 6 J. Nut. 5/16 K. Washer, 5/16 L. Washer, 5/16 M. Locknut, 5/16 N. Wing Nut E I / / Figure 12. A. Cup B. Lockwasher, 5/16 C.
INSTALLATION AND OPERATION - CART COLLECTOR ASSEMBLY 1. Remove all parts from inside the cart’s box. Open the bag of parts and sort the fasteners into groups for easier assembly of the cart (figure 16). 2. Turn cart box’on one side. a. Bolt U-bracket to bottom of box with two 5/ 16 x 3/4 long round head bolts.
BRACKET INSTALLATION The Cart Collector attaches to a mounting bracket, which is bolted to the tractor’s back plate. The same bracket is used on the riding mowers and the lawn tractors. Once bolted in place, the bracket never needs to be removed. For lawn tractors, see Section A.
3. The support rod and frame rod must be inserted into the cover (A, figure 21) as follows. a. The frame rod (C, figure 21) must be inserted through the bottom sleeve of the cover so that the two bent endsextend out openings, which are next to the cord loops (D).
Figure 24. A. Frame Rod 8. Frame Maintenance ~C. Clip D. Support Rod A WARNING The cart cover is subject to wear and deterioration. Check the cover frequently. Use a” approved replacement cover. The cover can be rinsed with a hose when dirty. A dirty cover will inhibit the fast flow of grass clippings into the cover.
1. Attaching: a. Attach the cart to the tractor by aligning the two ends of the H-frame to the holes in the bracket (figure 26). Use the holes that will make the cart level, Secure the cart to the bracket with twoclevis pins and hairpin totters. b. Attach the cart to the bracket at points‘%” or“C”.
I Figure 28. A. Nut B. Washer C. Nut Figure 29. A. Cover 6. Hook OPERATING WITHOUT COLLECTION SYSTEM - 36” MOWERS To remove the blower assembly, first loosen the front wing nut. To provide belt slack, push the belt retainer(B, figure 6). Slip the belt off the pulley.
.,,.,,.
EDGE OF DECK I - Align with deflector mounting holes. - I TEMPLATE FOR DRILLING MOUNTING HOLE FOR 36” TURBO VAC. LDrill g/32” Dia. Hole.
:‘~ ,‘,“:.
デバイスSnapper 1691525の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Snapper 1691525をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSnapper 1691525の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Snapper 1691525の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Snapper 1691525で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Snapper 1691525を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSnapper 1691525の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Snapper 1691525に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSnapper 1691525デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
