Snapperメーカー1694602 9247E, 11694602 9247E, 1694589 9560E, 1694597 9560M, 1694606 E9247, 1694590 1060E, 1694598 1の使用説明書/サービス説明書
ページ先へ移動 of 32
OPERA T OR’S MANU AL Lar g e Frame Sno wthr o wer s 960 Models Mfg. No. Description 1694602 9247E, 9HP Snowthrower 1694589 9560E, 9.5HP Snowthrower 1694597 9560M, 9.5HP Snowthrower (CE) 1694606 E9247, 9HP Snowthrower (CE) 1060 Models Mfg. No. Description 1694590 1060E, 10HP Snowthrower 1694598 1060M, 10HP Snowthrower (CE) 1070 Models Mfg.
T able of Contents 1 CONTENTS: Safety Rules & Inf ormation T raining ............................................................2 Preparation ......................................................2 Operation ......................................
2 This machine is capable of amputating hands and feet. Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment.
3 8. Always follow the engine manual instructions for stor- age preparations before storing the unit for both short and long term periods. 9. Always follow the engine manual instructions for proper start-up procedures when returning the unit to service.
4.
Decals 5 AVOID SERIOUS INJURY OR DEA TH • Read the operator's manual for operating and safety instructions. • Do not defeat the safety features of control. They are for your protection. • Keep machine properly maintained and serviced with all shields, guards, and protective devices in place.
Safety Icons 6 WARNING: READ OPERATOR’S MANUAL. Read and understand the Operator’s Manual before using this machine. DANGER: THROWN OBJECTS. This machine is capable of throwing objects and debris. Keep bystanders away. WARNING: REMOVE KEY BEFORE SERVICING.
Identification Numbers 7 When contacting your authorized dealer for replace- ment parts, service, or information you MUST have these numbers. Record your model name/number, manufacturer’s identi- fication numbers, and engine serial numbers in the space provided for easy access.
8 Features, Controls, & Operation 1 ,2.. CONTR OL LOCA TIONS The information below briefly describes the function of individual controls. Starting, stopping, and driving require the combined use of several controls applied in specific sequences.
Features & Controls 9 Fuel Fuel tank filler cap (see illustration). Note: The fuel shut off valve is located under the fuel tank or on the front of the engine. Close the valve when the snowthrower is not in use. Open the valve before starting. Primer Button When pressed, the primer button provides initial fuel to help start a cold engine.
Operation 10 GENERAL OPERA TION CHECKS BEFORE EA CH ST ART -UP 1. Make sure all safety guards are in place and all nuts, bolts and clips are secure. 2. Check to make sure that the clean-out is attached to the handle on the machine. Do not operate the machine without the clean-out tool properly stored on the handle.
Operation 11 4. Turn the choke knob (G) fully clockwise if engine is cold. (Do not choke a warm engine.) 5. Push the primer button (D) two times if engine is cold. (Do not prime a warm engine.) 6. Engine Mounted Electric Start: Press the starter button to crank the engine.
Operation 12 Figure 2. Controls (from operator’s position) A. Speed Selector B. Traction & Free-Hand™ Control C. Auger Engage Control D. Chute Direction Control Knob E. Chute Direction Control Remote F. Remote Deflector Control A B C D F OPERA TING THE SNO WTHRO WER 1.
Operation 13 DEFLECT OR The distance of the discharged snow is mainly controlled by the position of the deflector. (Engine speed also affects distance of discharge.) The more the deflector is tilted UP, the farther snow will be thrown. Models with Chute Deflector Knob See Figure 3.
Operation 14 EASY TURN™ FREEWHEELING AND TRA CTION DRIVE LOCK While Clearing Snow: For easy turning when using the snowthrower, squeeze the Easy Turn™ lever (Figure 6). Engaging the Easy Turn™ lever releases the right traction wheel but allows the left wheel to continue driving (Figure 6).
Storage 15 AFTER EA CH USE Normal use of the snowthrower may result in a build-up of packed snow in and around the starter cord housing and around engine controls.
16 Regular Maintenance A UGER GEAR CASE LUBRICA TION 1. Place the snowthrower on a level surface. 2. Remove the pipe plug (A, Figure 9). 3. Check the lubricant level. It should be level with the lower edge of the plug opening. If not, add The Dealer Line Winter Weight Worm Gear Oil (available from your dealer).
LUBRICA TION Remove wheels and grease axles once each year. Apply medium weight (10W) oil to points shown (See Figures 10-13). Apply 5W-50 synthetic motor oil to the friction disk drive hex shaft (A, Figure 11). Generally, all moving metal parts should be oiled where contact is made with other parts.
Regular Maintenance 18 CHECK / LUBRICA TE FREE-HAND LINKA GE Check the function of the Free-Hand controls: the con- trols should function as described in the CONTROLS section. It is critical for the safe operation of the unit that the controls disengage when released.
19.
20 T roubleshooting, Adjustments, Service W ARNING Before performing any adjustment or service to snowthrower, stop the engine and wait for moving parts to stop. Remove the key. To prevent accidental starting, disconnect the spark plug wire and fasten away from the plug.
T roubleshooting 21 PROBLEM POSSIBLE CA USE REMED Y Auger rotates, but snow is not thrown far enough 1. Chute deflector too low. 1. Adjust deflector as necessary. 2. Engine speed too slow. 2. Set speed to full throttle. 3. Ground speed too fast. 3. Use slower speed selector setting.
Adjustments 22 Figure 19. Auger Drive Linkage (Channel Handle Models) A. Turnbuckle B. Spring Hook C. Lever D. Nuts A D B C SPEED SELECT OR ADJUSTMENT 1. Loosen the two nuts (C, Figure 18). 2. Place the shift lever in 5th gear. 3. Push the lower rod into the housing and tighten the two nuts (C).
Adjustments 23 Figure 21. Traction Drive Adjustment (Channel Handle Models) A. Upper Rod B. Nuts C. Turnbuckle D. Lower Rod E. Spring B C B A E D 7. If auger does not operate properly, stop engine and recheck drive linkage adjustments. 8. If drive linkage is properly adjusted, auger drive belt tension may require adjustment.
Adjustments 24 MANU AL DISCHARGE CHUTE CONTR OL LINKA GE ADJUSTMENT Pinion Gear Adjustment If the discharge chute is difficult to operate, first lubricate the pinion gear (A, Figure 23) and ring gear (F).
Adjustments & Service 25 EASY TURN™ CABLE ADJUSTMENT If the Easy Turn™ cable has stretched, the gears will not disengage when the control lever is activated. Adjust the cable using the following procedure. 1. Turn the engine off and disconnect the spark plug wire.
Adjustments & Service 26 BEL T REPLA CEMENT 1. Turn off the engine, remove the spark plug wire, and wait for all moving parts to stop. Rotate the spout full right. Loosen the two screws (B, Figure 28) securing the belt cover. 2. Tilt the cover forward and work it off the snowthrower.
Service 27 Figure 31. Belt Pattern (viewed from front) A. Engine Pulley B. Drive Belt C. Idler Pulley D. Driven Pulley E. Engine Belt Stops F. Auger Pulley Belt Stops B C A E E F F D 6. Reverse the procedure to install the belts. Be sure there are no twists and the belts are properly seated in the grooves.
Specifications 28 ENGINE: 9 HP* Briggs & Stratton Make Briggs & Stratton Model Intek Snow Horsepower 9 @ 3600 rpm Displacement 18.6 Cu. in (305 cc) Oil Capacity 28 oz. (,84 L) 9.5 HP* Briggs & Stratton Make Briggs & Stratton Model Intek Snow Horsepower 9.
29 Parts & Accessories REPLA CEMENT P ARTS Replacement parts are available from your authorized dealer. Always use genuine Simplicity / Snapper Service Parts. TECHNICAL MANU ALS Additional copies of this manual are available, as well as fully illustrated parts lists.
30.
MANUFACTURING, INC. 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 www.simplicitymfg.com © Copyright 2004, Simplicity Manufacturing, Inc.
デバイスSnapper 1694602 9247E, 11694602 9247E, 1694589 9560E, 1694597 9560M, 1694606 E9247, 1694590 1060E, 1694598 1060M, 1694603 10287E, 1694607 E10287, 1694の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Snapper 1694602 9247E, 11694602 9247E, 1694589 9560E, 1694597 9560M, 1694606 E9247, 1694590 1060E, 1694598 1060M, 1694603 10287E, 1694607 E10287, 1694をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSnapper 1694602 9247E, 11694602 9247E, 1694589 9560E, 1694597 9560M, 1694606 E9247, 1694590 1060E, 1694598 1060M, 1694603 10287E, 1694607 E10287, 1694の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Snapper 1694602 9247E, 11694602 9247E, 1694589 9560E, 1694597 9560M, 1694606 E9247, 1694590 1060E, 1694598 1060M, 1694603 10287E, 1694607 E10287, 1694の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Snapper 1694602 9247E, 11694602 9247E, 1694589 9560E, 1694597 9560M, 1694606 E9247, 1694590 1060E, 1694598 1060M, 1694603 10287E, 1694607 E10287, 1694で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Snapper 1694602 9247E, 11694602 9247E, 1694589 9560E, 1694597 9560M, 1694606 E9247, 1694590 1060E, 1694598 1060M, 1694603 10287E, 1694607 E10287, 1694を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSnapper 1694602 9247E, 11694602 9247E, 1694589 9560E, 1694597 9560M, 1694606 E9247, 1694590 1060E, 1694598 1060M, 1694603 10287E, 1694607 E10287, 1694の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Snapper 1694602 9247E, 11694602 9247E, 1694589 9560E, 1694597 9560M, 1694606 E9247, 1694590 1060E, 1694598 1060M, 1694603 10287E, 1694607 E10287, 1694に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSnapper 1694602 9247E, 11694602 9247E, 1694589 9560E, 1694597 9560M, 1694606 E9247, 1694590 1060E, 1694598 1060M, 1694603 10287E, 1694607 E10287, 1694デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
