Snapperメーカー1726794の使用説明書/サービス説明書
ページ先へ移動 of 28
A TT A CHMENT OPERA T OR’S MANU AL Clean Sweep T riple Catcher Mfg. No. Description 1694499 Clean Sweep Triple Catcher 1726794 Rev. 00 Rev. Date 02/2004 TP 100-4032-00-AT-SN Clean Sweep T riple Catc.
1 Initial Collector Assembl y Assemble Catcher Bags ................................13 Install Cov er ...................................................13 Removing & Re-attac hing the T riple Catcher Removing the Gr ass Catcher ..................
2 Safety Rules & Information Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. The trian- gle in text signifies important cautions or warnings which must be followed.
3 BEFORE OPERA TION Clear the lawn of all sticks, stones, wire and other debris which may be caught or thrown by the mower blades. Check grass condition. If wet, wait until later in the day. If grass is wet, the grass catcher is likely to become plugged.
Initial T urbo Installation 4 50" 44" 35 49 48 7 8 6 4 5 Existing Hardware (Bolt, W asher , Lockw asher , & Nut) 40 41 42 43 22 38 44 1 1 2 3 9 18 18 15 16 17 8 14 13 Existing Pulley & Spacer T orque to 55-70 ft.
Initial T urbo Installation 5 Install Deflector Hinge Assembly 1. Remove the bolts (A, Figure 2) securing the RH arbor cover, then remove the cover from the deck. Discard the cover and bolts (A). 2. Remove and discard the plastic plugs from the deck at the locations used by bolts (F & B, Figure 5).
Initial T urbo Installation 6 Install Deflector 1. See Figure 6. Drill four 13/64” holes from the bottom of the deflector at the pre-molded drill points (A, bot- tom of deflector). 2. Attach the deflector to the support rod wire-form using four #10-14 x 3/4 truss head screws and nylock nuts.
Initial T urbo Installation 7 Install Idler Assembl y & Belt Cover 1. See Figure 9. Remove and discard the two taptite screws from locations (E). 2. Insert two 5/16-18 x 7/8 capscrews (C) through the mower deck and arbor. Tighten the capscrews. 3.
Initial T urbo Installation 8 Install Belt Cover Plate 1. Attach the belt cover plate (B, Figure 13 & 14) to the support bracket (E) using a 5/16-18 x 1 capscrew (C), washer (D) and nylock nut (F). NOTE: This cover plate must be able to pivot on the support bracket.
Initial T urbo Installation 9 Mower Dec k Arbor Pulley Mower Dec k T urbo Drive Pulle y T urbo Drive Pulley Idler Pulleys T o Slack en Belt CA UTION Before you begin operating the unit with the Turbo .
Initial Counter Balance & W eight Carrier Installation 10 Figure 1. Counter Balance Installation Figure 2. Front Weight Carrier Installation A. Washer, 5/16 E. Clips, Safety B. Capscrew, 5/16-18 x 1 F. Carrier, Weight C. Locknut, 5/16-18 G. Holes D.
Initiai Hitch & T ube Installation 11 Figure 1. Install Hitch Plate A. Hitch Plate D. Locknuts, 1/2-13 B. Heat Shield E. Upper & Lower C. Capscrews Hex, Bumper 1/2-13 x 1-1/4 F. Exisitng Holes Figure 3. Install Back Plate A. Back Plate and Support C.
Initial Hitch & T ube Installation 12 Figure 4. Assemble Tubes & Deflector A B G D H K F M L E C A. Deflector B. Back Plate C. Capscrew, 5/16-18 x 1 D. Socket E. Washer, 5/16 F. Locknut, 5/16-18 G. Upper Tube H. Middle Tube I. Lower Tube J. Washer K.
Initial Collector Assembly 13 COLLECT OR ASSEMBL Y Assemble Catcher Ba gs 1. See Figure 1. Insert the wire hoop (H) through the cloth bag (B). 2. Install the clamp (E) and hanger bracket (D). Secure with two 5/16-18 x 3/4 carriage bolts (C), lockwashers (G) and nuts (F).
Removing & Re-attaching Grass Catcher 14 REMOVING & RE-A TT ACHING THE GRASS CA TCHER Removing the Grass Catcher & tubes 1. Remove the hair pin clips (D, Figure 1) and hinge pins (B) and remove the cover (A). 2. Remove the bags (A, Figure 2) by lifting them off their hooks.
Removing and Re-attaching Grass Catcher 15 Figure 8. Install HInge Pins A. Cover C. Hinge B. Hinge Pin D. Hair Pin Clip A B C D Figure 7. Install Cover A. Cover C. Hinges B. Bags A C B Figure 6. Bags A. Bags B. Back Plate A Re-attaching the Grass Catcher 1.
FRONT WEIGHT CARRIER GROUP Manu al No . 1 6944 99 CLEAN SWEEP TRIPLE CATCHER SERIES 0 4.
FRONT WEIGHT CARRIER GROUP Footnotes: Manual No. 1694499 CLEAN SWEEP TRIPLE CATCHER SERIES 0 5 Part No Descri p tion Item Qt y Note 1 504908 2 1 MOU NT - WEI GH T CONSUMER Z TWIN & TRIPLE BAGG ER 986507- 01 2 1927557 4 NUT-HEX FL. WHIZ LK. .312-18 3 19 19326 4 WASHER .
TRIPLE CATCHER GROUP Manu al No . 1 6944 99 CLEAN SWEEP TRIPLE CATCHER SERIES 0 6.
TRIPLE CATCHER GROUP Footnotes: Manual No. 1694499 CLEAN SWEEP TRIPLE CATCHER SERIES 0 7 Part No Descri p tion Item Qt y Note 1 17 17025 1 COVER ASSEMBLY CONSUMER Z TRIPLE BAGGER 986509 - 01 2 1717082 1 SEAL 3 16 75707 3 TUBE - CLIP GR ASS BAG 4 19 31333 6 CARRIAGE BOLT .
TUBE & HITCH GROUP Manu al No . 1 6944 99 CLEAN SWEEP TRIPLE CATCHER SERIES 0 8.
TUBE & HITCH GROUP Footnotes: Manual No. 1694499 CLEAN SWEEP TRIPLE CATCHER SERIES 0 9 Part No Descri p tion Item Qt y Note 1 504915 2 1 LOW ER T UBE CONSUMER Z TRIPLE BAGGER 986506 - 02 2 1960 404 5 SCREW-TRUSS HD. #10-24 X .75 3 19 60096 5 WASHER .
TURBO MOUNTING GROUP Manu al No . 1 6944 99 CLEAN SWEEP TRIPLE CATCHER SERIES 0 10.
TURBO MOUNTING GROUP Footnotes: Manual No. 1694499 CLEAN SWEEP TRIPLE CATCHER SERIES 0 11 Part No Descri p tion Item Qt y Note 1 17 13523 1 NUT - SLEEVE . 562-18 x .75 CONSUMER Z TWIN & TRIPLE BAGG ER 986508 - 02 2 16 03592 1 WASHER .88 ID X 1.75 OK X .
TURBO MOUNTING GROUP Manu al No . 1 6944 99 CLEAN SWEEP TRIPLE CATCHER SERIES 0 12.
TURBO MOUNTING GROUP Footnotes: Manual No. 1694499 CLEAN SWEEP TRIPLE CATCHER SERIES 0 13 Part No Descri p tion Item Qt y Note 41 1916965 1 LOCKWASHER .375 42 1704768 1 BRACKET - Z 43 1724373 1 BRACKET - L 44 108717 1 SPACER 45 1714817 1 PULLEY - IDLER 2.
16 T orque Specification Chart FOR ST ANDARD MACHINE HARDW ARE (T olerance ± 20%) Hardware Grade SAE Grade 2 SAE Grade 5 SAE Grade 8 Size Of in/lbs in/lbs in/lbs Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm. 8-32 19 2.1 30 3.4 41 4.6 8-36 20 2.3 31 3.5 43 4.
MANUFACTURING, INC. 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 www.simplicitymfg.com © Copyright 2004 Simplicity Manufacturing, Inc.
デバイスSnapper 1726794の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Snapper 1726794をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSnapper 1726794の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Snapper 1726794の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Snapper 1726794で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Snapper 1726794を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSnapper 1726794の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Snapper 1726794に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSnapper 1726794デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
