Snapperメーカー8.5 TPの使用説明書/サービス説明書
ページ先へ移動 of 24
OPERA T OR’S MANU AL 8.5 TP Rear Tine Tiller Mfg. No. Description 1695583 6016RT, 8.5 TP Rear Tine Tiller 1695577 6016RT, 8.5 TP Front Tine Tiller Rear Tine Tiller 1737349 Revision A Rev.
2 Not for Reproduction.
3 T able of Contents 3 4 4 4 5 5 6 4 4 7 Unpack T iller ............................................................ Attach Handlebar to T iller ........................................ Fill Engine Crankcase ...........................................
4 O WNER’S RESPONSIBILITY Accurate assemb ly and saf e and eff ective use of the rototiller is the owner’ s responsibility . s Read and f ollow all saf ety instr uctions. s Carefully f ollow all assemb ly instr uctions. s Maintain the tiller according to directions and schedule included in this Ear thquake operator’ s manual.
5 IMPOR T ANT THE RIGHT AND LEFT SIDES OF Y OUR RO TO TILLER ARE DETER- MINED FROM THE OPERA TING POSI- TION AS Y OU F A CE THE DIRECTION OF FOR W ARD TRA VEL. ENGINE IS SHIPPED FROM F A CTOR Y WITHOUT OIL. Y OU MUST ADD EN- GINE OIL BEFORE ST ARTING ENGINE.
6 P art No. 1716747SM W ARNING INSTRUCTIONS Hood Decal P art No. 1716800SM W ARNING Belt Cover Decal P art No. 1716840SM TINES D ANGER Hood Flap Decal SAFETY DECALS This rototiller unit has been desig.
7 Y our rototiller comes fully assembled e xcept for a f ew par ts. The f ol- lowing instructions will help you unpac k your tiller and assemble and adjust your tiller’ s depth regulator le ver , cable tension and handlebar height. Y ou will need 2- 9/16” wrenches.
8 f orward drive saf ety control lev er detent pin f orward & re verse cab le recoil star t serial number plate wheel lock pin belt guard re verse driv e safety control le ver depth regulator le v.
9 PRE-ST AR T INSPECTION 1. Make sure all saf ety guards are in place and all nuts and bolts are secure. 2. Chec k oil lev el in engine crankcase. See your engine man ual for procedure and specifications. 3. Inspect air cleaner for cleanliness . See your engine man ual f or procedure.
10 IDLE SPEED Use the “low” position on the throttle le ver to reduce stress on the engine when tilling is not being perf ormed. Lowering the engine speed to “idle” will help extend the lif e of the motor , as well as conser ve fuel and reduce the noise le vel of the equipment.
11 DRIVE SAFETY CONTROL LEVERS FOR W ARD LEVER Engages wheels and tines into f orward. Pulling the drive saf ety control lev er labeled (FORW ARD) toward the handlebar engages the wheels and tines. Releasing the lev er stops the wheels and tines and brings the tiller to a complete stop.
11 WHEEL LOCK PINS Place wheels in tilling position. 1. Remov e lock pin. Align hole in axle with hole in wheel hub . (SEE FIGURE 2) 2. Inser t lock pin through holes, f old lock pin ring to secure pin to axle. 3. Fir mly lock wheel and axle together bef ore tilling.
12 re verse cab le f orward cab le upper jam nut lower jam n ut depth regulator brack et depth regulator lev er detent pin DO NO T ADJUST TILLING DEPTH UNLESS DRIVE SAFETY CONTROL LEVERS ARE RELEASED TO NEUTRAL POSITION.
14 TILLING TIPS The ke y to successful tilling is to begin with a shallow cut on the first pass, and then work an inch or two deeper on each successiv e pass.
15 SER VICING THE RO T O TILLER The f ollowing inf or mation will help you mak e the necessar y checks and perf orm the procedures required to follow the normal care recommendations made f or your rototiller unit. If you pref er , your local authorized dealer can make these chec ks and perf orm the required procedures for you.
16 CHANGE FORWARD/REVERSE BEL T 1. T ur n off engine. Engine must be cool. 2. Remov e spar k plug wire and secure from spark plug. 3. Remov e belt guard. sREM ov e the f orward belt from the f orward engine pulley: - gently pull the engine recoil rope to rotate the pulley .
17 ENGINE MAINTENANCE Ref er to the engine manual included in y our par ts pack et for inf ormation on engine maintenance. Y our engine manual provides detailed inf ormation and a maintenance schedule for perf or ming the f ollowing tasks: 1 . Check oil le vel bef ore each use or after ev er y 8 hours of operation.
18 LUBRICA TION Proper lubrication of moving mechanical par ts is critical for proper care and maintenance. Oil the moving par ts at 10 hour inter vals using a 30 weight oil. CLEAN TINE AXLE SHAFT 1. T ur n off engine. Engine must be cool. 2. Remov e spar k plug wire and secure from spark plug.
19 TROUBLESHOO TING GUIDE While normal care and routine maintenance will extend the lif e of your rototiller , prolonged or constant use may e ventually require that ser vice be perf or med to allow it to continue operating properly . The troubleshooting guide belo w lists the most common problems, causes and remedies.
P age 20 PROBLEM REMED Y/A CTION Belts squeal in neutral and/or re verse s Adjust f orward belt guide: turn engine off and allow to cool - disconnect spark plug wire and secure from spark plug - remov.
2 1 T echnical Manuals Additional T echnical Literature A vailable Additional copies of this manual are available, as well as fully illustrated parts lists.
22 Not for Reproduction.
23 Not for Reproduction.
Briggs & Stratton Power Products Group, L.L.C. Copyright © 2008 Briggs & Stratton Corporation Milwaukee, WI USA. All Rights Reserved www.BRIGGSandSTRATTON.
デバイスSnapper 8.5 TPの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Snapper 8.5 TPをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSnapper 8.5 TPの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Snapper 8.5 TPの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Snapper 8.5 TPで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Snapper 8.5 TPを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSnapper 8.5 TPの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Snapper 8.5 TPに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSnapper 8.5 TPデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
