SnapperメーカーELT180H33IBVの使用説明書/サービス説明書
ページ先へ移動 of 40
Safety Instructions & Operator’s Manual for EUROPEAN LAWN TRACTOR HYDROSTATIC DRIVE SERIES I MODEL ELT180H33IBV MODEL NUMBER EXPLANATION E LT 180 H 33 I B V EUROPEAN MODEL MODEL DESIGNATION ENGI.
2 IMPORTANT SAFETY INSTRUCTIONS WARNING: This pow erful cutting machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply w ith the follow ing SAFETY instructions could result in serious injury or death to the operator or other persons.
3 IMPORTANT SAFETY INSTRUCTIONS PREPARATION (Continued From Previous Page) 7. Keep people and pets out of mow ing area. Immediately STOP blades, STOP engine, and STOP machine if anyone enters the area. 8. Check shields, deflectors, sw itches, blade controls and other safety dev ices frequently for proper operation and location.
4 IMPORTANT SAFETY INSTRUCTIONS TOWING 1. Tow only with a machine that has a hitch designed for tow ing. DO NOT attach tow ed equipment except at the hitch point. 2. Follow the manufacturer’s recommendation for w eight limits for tow ed equipment and tow ing on slopes.
5 TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS ........... 2-4 TABLE OF CONTENTS ......................................... 5 SECTION 1 - FAMILIARIZATION ...................... 6-8 Compone nts ....................................................... 6 Controls .
6 Section 1 - FAMILIARIZATION FIGURE 1.1 COMPONENTS The nomenclature drawings above, illustrate the essential components of the SNAPPER Lawn Tractor. It is recommended that all operators of this equipment become thoroughly familiar with the components and their operation BEFORE OPERATING.
7 Section 1 - FAMILIARIZATION – DECALS / SYMBOLS All operators should locate, read and understand all decals on the machine before attempting any operation of the machine. If any operator has difficulty in understanding certain symbols incorporated in the decals, an authorized SNAPPER dealer should be contacted for explanation.
8 Section 1 - FAMILIARIZATION – DECALS / SYMBOLS SAFETY INSTRUCTIONS. OPERA TING INSTRUCTIONS. CONTROL IDENTIFICATION – 7-2754 FORWARD REVERSE NEUTRAL DIRECTION A ND SPEED CONTROL 7-3424 HEIGHT OF.
9 Section 2 - OPERATING INSTRUCTIONS 2.1 PRE-START CHECKLIST Make the following checks and perform service as required before each start-up. 2.1.1. Check tires and add air as needed to bring pressure to 12 P.S.I. in front tires and 12 P.S.I. in rear tires.
10 Section 2 - OPERATING INSTRUCTIONS 2.3 STARTING & OPERATION 2.3.1. STARTING ENGINE 1. Take a comfortable position in seat of machine, look around to make sure that the area you are going to mow is clear of people, children and pets.
11 Section 2 - OPERATING INSTRUCTIONS 2.3 STARTING & OPERATION (continued) 2.3.2. STARTING WHEEL DRIVE 1. Shift speed control lever to neutral. 2. Start engine. Refer to Section “STARTING ENGINE”. 3. Release clutch/brake pedal. 4. Slowly shift speed control lever forward for forward motion or to the rear for reverse motion.
12 Section 2 - OPERATING INSTRUCTIONS 2.4 STOPPING 2.4.3. STOPPING MOWER BLADE 1. Stop mower blade by moving blade engagement lever to the "OFF" position. See Figure 2.11. FIGURE 2.11 WARNING Once blade is disengaged, it should come to a complete stop in 5 seconds or less.
13 Section 2 - OPERATING INSTRUCTIONS 2.6. ROLLING TRACTOR WITH ENGINE OFF Rolling Hydro Models 1. With engine "OFF", move to rear of tractor. 2. Pull the roll release control all the way out to disengage the hydro transmission. See Figure 2.
14 Section 2 - OPERATING INSTRUCTIONS 2.7. REVERSE LOCKOUT MECHANISM Data indicates that tragi c back-over accidents occur each year. These accidents usually involve unsupervised children.
15 Section 3 - MAINTENANCE 3.1 INTRODUCTION To retain the quality of the Tractor, use genuine SNAPPER replacement parts only. Contact a loca l SNAPPER dealer for parts and service assistance. For the correct part or information for a particular Tractor, al w a y s m e n ti o n the model and serial number.
16 Section 3 - MAINTENANCE 3.2.4. CHECK DECK DRIVE BELT 1. With engine "OFF", move blade engagement lever to "ON". 2. Measure blade cable extension spring. Spring should extend 1" +/-1/8" fo r proper belt tension. See Figure 3.
17 Section 3 - MAINTENANCE 3.3.4. TRACTOR LUBRICATION 1. Front Wheel Bearings Lubricate each front wheel bearing through the grease fitting on wheel hub. Using general purpose grease in a grease gun, add grease until grease purges from bearing. See Figure 3.
18 Section 3 - MAINTENANCE 3.3.4. TRACTOR LUBRICATION (Continued From Previous Page) 7. Steering Tie Rod Lubricate both ends of steering tie rod with a small amount of 30 wt. motor oil from an oil can. See Figure 3.10. FIGURE 3.10 8. Blade Engagement Mechanism Using 30 wt.
19 Section 3 - MAINTENANCE 3.4 ANNUALLY (END OF EACH SEASON) 3.4.2. FUEL FILTER (Continued From Previous Page) 3. Install new fuel filter part number 1-4359. See Figure 3.14. FIGURE 3.14 4. Fill fuel tank with fresh gasoline. Refer to engine owner's manual for fuel specifications.
20 Section 4 - ADJUSTMENT & REPAIR WARNING DO NOT attempt any adjustments, maintenance or service with the engine or blade running. STOP blade. STOP engine. Set brake. Remove key . Remove spark plug w ire from spark plug and secure w ire aw ay from spark plug.
21 Section 4 - ADJUSTMENT & REPAIR 4.2.2. BLADE BELT ADJUSTMENT – 33” Deck (Continued from previous page) IMPORTANT: If deck front to rear level is not correct, this could cause blade belt problems. 6. Move blade engagement lever to "ON".
22 Section 4 - ADJUSTMENT & REPAIR WARNING DO NOT attempt any adjustments, maintenance or service with the engine or blade running. STOP blade. STOP engine. Set brake. Remove key . Remove spark plug w ire from spark plug and secure w ire aw ay from spark plug.
23 Section 4 - ADJUSTMENT & REPAIR WARNING DO NOT attempt any adjustments, maintenance or service with the engine or blade running. STOP blade. STOP engine. Set brake. Remove key . Remove spark plug w ire from spark plug and secure w ire aw ay from spark plug.
24 Section 4 - ADJUSTMENT & REPAIR 4.3 TRACTOR DRIVE COMPONENTS 4.3.1. BRAKE ADJUSTMENT 1. To be properly adjusted, the brake should stop the tractor in approximately 6 feet from top speed when the clutch/brake pedal is fully depressed. 2. Adjust brake when necessary as follows: 3.
25 Section 4 - ADJUSTMENT & REPAIR WARNING DO NOT attempt any adjustments, maintenance or service with the engine or blade running. STOP blade. STOP engine. Set brake. Remove key . Remove spark plug w ire from spark plug and secure w ire aw ay from spark plug.
26 Section 4 - ADJUSTMENT & REPAIR 4.4.2. (NINJA) BL ADE WEAR LIMITS The ninja recycling blade requires more frequent service intervals than standard blades. Check for excessive wear and damage before each use. See Figure 4.18. FIGURE 4.18 4.4.3. (STANDARD) BLADE SHARPENING Blades should be kept sharp at all times.
27 Section 4 - ADJUSTMENT & REPAIR 4.4.5. 33" MOWER BLADE REPLACEMENT (Continued) 6. Install new blade, part number 3-4168, onto blade mounting bar. 7. Torque blade to 30 to 40 ft lbs. of torque. 4.4.6 TRACTION DRIVE BELT REPLACEMENT It is necessary to remove deck in order to replace belts.
28 Section 4 - ADJUSTMENT & REPAIR Traction drive belt removal (Continued from previous page) 2. Slide belt guide assembly to the rear and remove. 3. Disconnect traction belt idler pulley spring from tractor frame. See Figure 4.26. FIGURE 4.26 WARNING DO NOT attempt any adjustments, maintenance or service with the engine or blade running.
29 Section 4 - ADJUSTMENT & REPAIR Traction drive belt replacement (Continued from previous page) NOTE: When installing a new belt, make certain the stationary idler is mounted in the hole closest to the L.H. side of the tractor. See Figure 4.29. 4.
30 Section 4 - ADJUSTMENT & REPAIR 4.5 BATTERY 4.5.1. BATTERY REMOVAL 1. Raise operator's seat. 2. Remove the two adjusting knobs. 3. Remove seat assembly and move forward. Use care not to disconnect wires from seat switch. See Figure 4.33. FIGURE 4.
31 Section 4 - ADJUSTMENT & REPAIR WARNING DO NOT OVERFILL! DO NOT attempt to service or charge the battery while it is installed on the machine. DO NOT use “BOOST” chargers on the battery. 4.5.5. BATTERY TESTING There are two types of battery tests: Unloaded and Loaded.
32 Section 4 - ADJUSTMENT & REPAIR AVAILABLE ACCESSORIES The SNAPPER Series H LAWN TRACTOR can be equipped with a va riety of accessories that increase its versatility. The accessories available for each model are listed in the chart below. Contact an authorized SNAPPER dealer for ordering any of the accessories desired.
33 SECTION 5 - ELECTRICAL SYSTEM Figure 5.1 illustrates typical harness routing on some Snapper Lawn Tractors. Use this when locating various electrical components. FIGURE 5.1 TO BATTERY NEGATIVE (-) TERMINAL TO BATTERY POSITIVE (+) TERMINAL SOLENOID (UNDER SEAT) SEAT SWITCH IGNITION SWITCH HEADLIGHT SWITCH 20 A MP FUSE PARK BRAKE SWITCH TO R.
34 SECTION 5 - ELECTRICAL SYSTEM SCHEMATICS BRIGGS & STRATTON WITH LIGHTS FIGURE 5.2.
35 TROUBLESHOOTING GUIDE PROBLEM PROBABLE CAUSE CORRECTIVE ACTION Starter Will Not Crank Engine 1. Battery dead. 1. Service battery. 2. Blown fuse. 2. Replace fuse. 3. Electrical connections l oose or corroded. 3. Clean and check connections for good contact.
36 TROUBLESHOOTING GUIDE PROBLEM PROBABLE CAUSE CORRECTIVE ACTION Tractor Will Not Move Or Loss Of Traction 1. Speed control handle in the neutral “N” position. 1. Place speed control in desired speed. 2. Roll release control in “ROLL” position.
37 MAINTENANCE SCHEDULE SUBJECT SERVICE TO BE PERFORMED REFERENCE PAGES EACH USE 5 HOURS 25 HOURS 50 HOURS 100 HOURS EACH SEASON Engine Check Oil Level Page 9 X Engine Initial Oil Change Page 15 X Eng.
38 2 YEAR LIMITED WARRANTY For two (2) years from purchase date for the orig inal purchaser's residential, non-commercial use, SNAPPER , through any authorized SNAPPER dealer will replace, free o.
39 SERVICE NOTES ___________________________________________________________________ ___________________________________________________________________ _______________________________________________.
40 Safety Instructions & Operator’s Manual for EUROPEAN LAWN TRACTOR HYDROSTATIC DRIVE SERIES I IMPORTANT Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufactured. The labels on those engines contai n very important emissions information and critical safety warnings.
デバイスSnapper ELT180H33IBVの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Snapper ELT180H33IBVをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSnapper ELT180H33IBVの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Snapper ELT180H33IBVの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Snapper ELT180H33IBVで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Snapper ELT180H33IBVを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSnapper ELT180H33IBVの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Snapper ELT180H33IBVに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSnapper ELT180H33IBVデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
