SnapperメーカーEZF6100M, EZF2100DKU, EZF2300GKU, EZF5200Mの使用説明書/サービス説明書
ページ先へ移動 of 32
Safety Instructions & Operator’s Manual for OUT FRONT Z-RIDER HYDRO DRIVE SERIES 0 POWER UNIT MODELS EZF2100DKU EZF2300GKU MOWER UNIT MODELS EZF5200M EZF6100M MODEL NUMBER EXPLA NA TION E Z F 21.
2 IMPORTA NT SA FETY INSTRUCTIONS WARNING: This pow erful cut ting machine is cap able of amput ating hands an d feet and can throw objects that can cause in jury and damage! Failure to comply wi th the follo wing SAFETY inst ructions coul d result in serious injury or death to the ope rator or other persons.
3 IMPORTA NT SA FETY INSTRUCTIONS PREPA RA TION (Continued From Pre vious Page) 5. Practice operatio n of machine w ith BLADES OF F to learn controls and develop skills. 6. Check th e area to be mow ed and remov e all objects such as toys, wire, rocks, limbs and other objects that cou ld cause injury if thro wn by blades or interfere with mowing.
4 TABLE OF CONTENTS IMPORTA NT SA FETY INSTRUCTIONS ................................................ 2-3 TA BLE OF CO NTENTS............................................................................. 4 SECTION 1 - FA MILIA RIZA TION ................
5 Section 1 – FA MILIA RIZA TION FIGURE 1.1 1. 1 INTRODUCT ION This manual has been prepared for the operator ’s of the SNAPPER OUT FRONT Z-RI DER. Its purpose, aside from rec omm ending standard oper ating procedures and routine s ervice requirem ents, is to prom ote SAFETY through the use of accepted operating practices.
6 MACHINE MOTION CONTROL - Single lever, multi- directiona l & continuously varia ble, controls direction of motion & spee d of motion. Forward displacement of control produces forward motion. Rearward displacemen t of control produces rearward mo tion.
7 SYMBOLS ENGINE SPEED CONTROL RA BBIT - FAST TURT LE - SLOW DIESEL FU EL ONLY CUTT ING HEIGHT CONTROL SWITCH - Mov e switch in direction of plus symbol to increase cutt ing height / Mov e switch in direction of minus symbol to decrease cutt ing height .
8 DO NOT open or remove guards or shie lds while engine is running. STOP engine. A llow all motion to completely stop before approaching. DO NOT approach mower w hile engine is running. STOP engine. A llow all mot ion to completely stop before approaching.
9 Section 2 - OPERA T ING INSTRUCTIONS 2.1 PRE- START CHECK L IST Make the f ollowing checks and perform the service requir ed before eac h start-up. 2.1.1. Check tires and add or releas e air as needed to bring press ure in drive tires to: 12 psi (T urf Type Tires ), 5 ps i (All Terr ain Type Tires) and 25 psi in rear cas ter tires.
10 Section 2 - OPERA T ING INSTRUCTIONS IMPORT A NT: T his Out Front Z-Rider is equipped with hydros tatic drive. T he forward and rear w ard movement of the mach ine is controlled b y a joystick lev er. Joys tick operations should be pe rformed only from the operator’s position in t he seat.
11 Section 2 - OPERA T ING INSTRUCTIONS 2.2.1. STA RTING ENGINE (Continued from previous page) FIGURE 2.6 6. IMPO RTANT: (Diesel Eng ine Only) Use the Glow Plug only if engine is cold or outside temper ature is cold. Rotate k ey counter clock wise to the preheat position (G L letter designation on switch) to allow the glow lamp to heat up.
12 Section 2 - OPERA T ING INSTRUCTIONS 2.2.4. PA RKING BRA KE 1. Engage park ing brak e by pulling the park ing brak e lever bac k to the “ ON” position. See Figure 2.8. 2. Release par king brake by moving brak e lever down to the “OFF” pos ition.
13 Section 2 - OPERA T ING INSTRUCTIONS 2.3. OPERA T ION – MOT ION CONTROL 2.3.1. DRIVING MA CHINE IMPO RTANT: The j oy s tick lever has to be m anually mo ved to propel mac hine. Alway s return the joystick with hand assistance to the neutral pos ition to stop ma chine.
14 Section 3 - MA INTENA NCE 3.1 INTRODUCT ION To retain the quality of the SNAPPER Out Fr ont Z-Rider, use genuine SNAPPER replacem ent parts only . Contact a local SNAPPER dealer f or parts and servic e assistance. For the cor rect part or inform ation for a particular SNAPPER Out Front Z- Rider, alway s m ention the model and serial number .
15 Section 3 - MA INTENA NCE 3.2.3. CHECK MOW ER DRIVE BELT 1. Drive Belt Cov er Removal a. Lower deck to lowest s etting. b. Remove knobs that secur e the deck cover. See Figure 3.3. c. Rem ove cover to gain acces s to deck belt. FIGURE 3.3 2. Checking Belt Tension The idler and spring provide pr oper belt tension and require no adj ustm ent.
16 Section 3 - MA INTENA NCE 3.3.3. RIDING MOW ER - LUBRICA TION 1. Front & Rear Wheel Bearings Lubricate with Kendall NLGI No. 2 lithium grease or equivalent, from a grease gun. See F igure 3.5. FIGURE 3.5 2. Transaxle Check the level of f luid in both of the fluid reser voirs.
17 Section 3 - MA INTENA NCE 3.5 ANNUA LLY (END OF EA CH SEA SON) (Continued from previous P age) 3.5.2. FUEL FIL TER (D IESEL ENGINE ON LY) Service f uel f ilter as instructed in engine owner’s manual. Turn key to “O FF” position. Engine MUST be stopped and MUST be c old before rem oving filter.
18 Section 3 - MA INTENA NCE 3.6 DECK REMOVAL (Continued From Pre vious Page) 4. Rotate spr ing loaded hitch latch pins (Located on both hitch plates ) to the unlatched position. See Figure 3.10. 5. Move deck lift s witch as if to lower deck and the lif t arm will m ove up in the hitc h plates.
19 Section 4 - A DJUSTMENTS & REPA IR DA NGER Exercise EXT REME CAUTION wh en making this adjustment, due to clos e proximity of moving parts. 4.1 NEUTRA L POSITION A DJUSTM ENTS The j oy stic k contr ols the movem ent and stopping of the machine.
20 Section 4 - A DJUSTMENTS & REPA IR 4.2.1. M OW ER DECK ADJUSTM ENT ( LEVELNESS) SIDE to SIDE and FRONT to REA R (Continued from previous page ) 5. Retighten leveling bracket bolts. 6. Remove both bolts ( one from each side) from the front por tion of the link weldment.
21 Section 4 - A DJUSTMENTS & REPA IR 4.5 MOWER BLADE RE P LACEMENT 4.5.1. BLA DE WEAR LIMIT S (Continued from previous page ) FIGURE 4.5 WA RNING DO NOT u se a cutting blad e that show s signs of excessive w ear o r damage. Refer to Fig ure 4.5. W ea r heavy lea ther gloves when handling or working around cutting blades.
22 Section 4 - A DJUSTMENTS & REPA IR 4.6 MOWER DRIVE BELT, ENGINE BELT & HYDRO PUM P BELT REPLACEMENT Inspect all belts. Replace belt if it shows s igns of excess ive wear, damage and/or is broken. WA RNING DO NOT attempt any adjustments, main tenance or service with the engine or blades r unning.
23 Section 4 - A DJUSTMENTS & REPA IR 4.7 BA TT ERY 4.7.1. BA T TERY REMOVAL 1. Rem ove battery retainer. 2. Slide battery from battery box to gain access to term inal cables.
24 Section 4 - A DJUSTMENTS & REPA IR 4.7 BA TT ERY Battery Condition Chart State of Charge Sy ringe Hy drometer Di gital Voltmeter Five Ball Hy drometer 100% Charged w/ Sulfate Stop 1.280 12.80v Five Balls Floating 100% Charged 1.265 12.60v Four Balls Floating 75% Charged 1.
25 Section 4 - A DJUSTMENTS & REPA IR 4.8 MO WER SPINDLES (Field Serviceable Spindles) BEA RING REPLACEMENT In the event that a spindle bearing requires replacem ent, the SNAPPER Field Serviceable Spindles have been designed s o that no special tools or pres ses are requir ed.
26 TROUBLESHOOTING PROBL EM PROBABLE CAUS E CORRECTIVE A CT ION Starter Will Not Crank 1. Battery dead. 1. Service battery. Engine 2. Blown fuse. 2. Replace fuse. 3. Electrical connections loose or corroded. 3. Cl ean and check connections for good contact.
27 TROUBLESHOOTING PROBLEM PROBABLE CA USE CORRECTIVE ACTION Tractor Will Not Move 1. Joystick in the neutral “N” position. 1. Place joystick in desired speed position. Loss Of Traction 2. Roll release lever is in “RO LL” position. 2. Mov e roll release lever to the engaged position.
28 SERVICE SCHEDULE ITEM SERVICE PERFORMED REF. EACH USE 5 HRS 25 HRS 50 HRS 75 HRS 100 HRS EACH SEASON Engine Oil Check Oil Level Page 9 X Initial Oil Change Page 15 X Periodic Oil Change Page 14 X *.
29 2 YEA R LIMITED WARRA NTY For two (2) y ears f rom purchase date f or the original purc haser's use, SN A PPER , through any authorized SNA PPER dealer will replac e, free of charge (exc ept f.
30 NOTES.
31 NOTES.
32 Safety Instructions & Operator’s Manual for OUT FRONT Z-RIDER HYDRO DRIVE SERIES 0 IMPORTANT Snapper products are built using engines that meet or exceed all a pplicable emissions requirements on the date manufactured. The labels on thos e engines contain very important emissions infor mation and critical safety warnings.
デバイスSnapper EZF6100M, EZF2100DKU, EZF2300GKU, EZF5200Mの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Snapper EZF6100M, EZF2100DKU, EZF2300GKU, EZF5200Mをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSnapper EZF6100M, EZF2100DKU, EZF2300GKU, EZF5200Mの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Snapper EZF6100M, EZF2100DKU, EZF2300GKU, EZF5200Mの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Snapper EZF6100M, EZF2100DKU, EZF2300GKU, EZF5200Mで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Snapper EZF6100M, EZF2100DKU, EZF2300GKU, EZF5200Mを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSnapper EZF6100M, EZF2100DKU, EZF2300GKU, EZF5200Mの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Snapper EZF6100M, EZF2100DKU, EZF2300GKU, EZF5200Mに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSnapper EZF6100M, EZF2100DKU, EZF2300GKU, EZF5200Mデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
