SnapperメーカーFB13250BS, GM2515KAW, GM2513Hの使用説明書/サービス説明書
ページ先へ移動 of 24
OPERA T OR’S MANU AL Mfg. No. Model No. Description 7085922 FB13250BS 13 hp Briggs, Hydro-Drive 7085923 GM2515KA W 15 hp Kaw asaki, Hydro-Dr iv e 7085924 GM2513H 13 hp Honda, Hydro-Drive Field and Brush Mo wer Manual No.
1 T roub leshooting, Adjustment and Service .....14 Chart .....................................................................14 Travel Control Adjustment ....................................16 Blade Clutch Adjustment ................................
2 SAFE OPERA TION PRA CTICES FOR W ALK-BEHIND MO WERS This cutting machine is capable of amputating hands and feet and throwing objects. Failure to observe the follow- ing safety instructions could result in serious injury or death. GENERAL OPERA TION • Read, understand, and follow all instructions on the machine and in the manual(s).
3 Safety Rules and Information SLOPE OPERA TION Slopes are a major factor related to slip and fall acci- dents, which can result in severe injury. All slopes require extra caution. If you feel uneasy on a slope, do not mow it. Do • Mow across the face of slopes; never up and down.
4 Safety Rules & Information SER VICE AND MAINTENANCE • Use extra care in handling gasoline and other fuels. They are flammable and vapors are explosive. a) Use only an approved container. b) Never remove gas cap or add fuel with the engine running.
5 Safety and Instructional Decals Decal - Warning (7028490) Important Safety Operating Instructions. Read and understand before operating machine Decal - Engine Throttle Control (7029167) Models - All.
6 Features & Controls Engine On/Starter Rotate this key switch to the ON position before pulling on the starter rope. If the mower is equipped with the optional electric start- ing system, rotate the key past the ON position to engage the starter.
7 Operating the Mower Engage Disengage Figure 4 - Traction Drive / Freewheel Control ST AR TING THE ENGINE NOTE - The procedures outlined within this section are general guidelines, and are in no way meant to replace or supercede engine manufacturer's operating instruc- tions.
8 Operating the Mower T o Pr opel Unit Forwar d: • Grasping both upper handle/safety bar (A, Figure 5) and lower portion of traction drive engagement bar (B) with both hands, slowly begin squeezing engage- ment bar up toward handle. The unit should begin moving forward.
9 Operating the Mower OFF RUN ST ART A Figure 7 - PTO Engaged A. Blade Engagement Lever in engaged position. OFF RUN ST ART A Figure 8 - PTO Disengaged A.
10 Operating the Mower A D C C B Figure 9 - Adjusting Height A. Skid B. Capscrew C. Washer D. Nut T O ADJUST CUTTING HEIGHT The front skids on the brush cutter have 3 sets of holes (Figure 9) for heig.
11 Regular Maintenance LUBRICA TION Service Interval: Every 25 Hours Lubricate the unit at the locations shown in Figure 10 as well as the lubrication points listed. Generally, all moving parts should be oiled where contact is made with other parts. Keep oil and grease off belts and pulleys.
12 Regular Maintenance TIRE PRESSURE Tire pressure is 20 psi (1.4 bar). B A TTER Y SER VICE Cleaning the Battery and Cables - 9HP Models Service Interval: Every 100 Hours 1. Disconnect the cables from the battery, negative cable first (C, Figure 13a).
13 Regular Maintenance SER VICING THE MO WER BLADES Service Interval: Every 100 Hours or As Required 1. Raise the front end of the brush mower and securely support in the raised position. 2. Blades should be sharp and free of nicks and dents. If worn or damaged, replace the blades as described in following steps.
14 T roubleshooting, Adjustment, & Service TR OUBLESHOO TING PROBLEM CAUSE REMEDY Engine will not turnover or start. 1. PTO lever in the engaged position. Place in disengaged position. 2. Out of fuel. If the engine is hot, allow it to cool, then refill the fuel tank.
15 T roubleshooting, Adjustment & Service T r oubleshooting Cont. Blade will not engage. 1. Blade clutch rod too loose. See Blade Clutch Adjustment Section. 2. Blade belt worn or broken. Turn off engine and inspect belt. Adjust or replace as required.
16 T roubleshooting, Adjustment, & Service TRA VEL CONTROL ADJUSTMENT Serial Number 0-011903999 1. The Travel Control engagement bars (A, Figure 16a) should be an equal distance from the Upper Handle Bar. If they are not, adjust their position. 2.
17 T roubleshooting, Adjustment, & Service A D C B E Figure 17 - Blade Clutch Adjustment A. Clutch Rod B. Clutch Rod Lever C. Clutch Rod Fitting D.
18 T roubleshooting, Adjustment, & Service BLADE BRAKE ADJUSTMENT The mower blade should stop within 5 seconds after the Blade Engagement Lever is moved to the DISEN- GAGED position. This adjustment is checked by: 1. Remove blade clutch cover plate (A, Figure 19).
19 T roubleshooting, Adjustment, & Service A D B 1/8” Max. C Figure 21 - Traction Drive Belt Adjustment A. Transmission Pulley B. Drive Belt C. Engine Pulley D.
20 T roubleshooting, Adjustment & Service E D G F B C A Figure 24 - Belt Alignment A. Blade Drive Pulley B. Mower Belt C. Mower Tension Idler D. Transmission Pulley E.
21 Specifications Parts & Accessories ENGINEl BRIGGS HONDA KAWASAKI BRIGGS Engine 13 HP B&S 13 HP Honda 15 HP V-twin 16 HP B&S Transmission Hydro/Variable Hydro/Variable Hydro/Variable Hydro/Variable Ground Speed (mph) Infinite (.01 - 6) Infinite (.
22 Notes.
A Division of Simplicity Manufacturing, Inc. 535 Macon Street/PO Box 777 McDonough, GA 30253 © Copyright 2004 All Rights Reserved. Printed in USA..
デバイスSnapper FB13250BS, GM2515KAW, GM2513Hの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Snapper FB13250BS, GM2515KAW, GM2513Hをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSnapper FB13250BS, GM2515KAW, GM2513Hの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Snapper FB13250BS, GM2515KAW, GM2513Hの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Snapper FB13250BS, GM2515KAW, GM2513Hで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Snapper FB13250BS, GM2515KAW, GM2513Hを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSnapper FB13250BS, GM2515KAW, GM2513Hの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Snapper FB13250BS, GM2515KAW, GM2513Hに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSnapper FB13250BS, GM2515KAW, GM2513Hデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
