SnapperメーカーLT-200 Seriesの使用説明書/サービス説明書
ページ先へ移動 of 40
OPERA T OR’S MANU AL 18.5HP Hydro Tractors Mfg. No. Description 2690685 ELT18538, 18.5HP (CE) 2690781 ELT18540, 18.5HP (CE) 20HP Hydro Tractors Mfg. No. Description 2690689 ELT2044, 20HP (CE) 38” Mower Decks Mfg. No. Description 1695146 38” Mower Deck (CE) 40” Mower Decks Mfg.
.
1 T roub leshooting, Adjustment & Service .........28 Troubleshooting the Tractor ..................................28 Troubleshooting the Mower ..................................29 Battery Charging ................................................
2 Safety Rules & Information TP 600-2459-08-UV-SMA Operating Safety Congratulations on purchasing a superior-quality piece of lawn and garden equipment. Our products are designed and manufactured to meet or exceed all industry standards for safety.
3 Safety Rules and Information Slope Operation You could be seriously injured or even killed if you use this unit on too steep an incline. Using the unit on a slope that is too steep or where you don’t have adequate traction can cause you to lose control or roll over.
4 Safety Rules & Information GENERAL OPERA TION 1. Read, understand, and follow all instructions in the manual and on the unit before starting. 2. Do not put hands or feet near rotating parts or under the machine. Keep clear of the discharge opening at all times.
5 Safety Rules and Information CHILDREN Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the unit and the mowing activity. Never assume that children will remain where you last saw them.
6 Safety Rules & Information SER VICE AND MAINTENANCE Safe Handling of Gasoline 1. Extinguish all cigarettes, cigars, pipes, and other sources of ignition. 2. Use only approved gasoline containers. 3. Never remove the gas cap or add fuel with the engine running.
7 Identification Numbers Tractor ID Tag Mower ID Tag When contacting your authorized dealer for replacement parts, service, or information you MUST have these numbers. Record your model name/number, manufacturer’s identification numbers, and engine serial numbers in the space provided for easy access.
8 Safety Decals Warning: Read Operator’s Manual. Read and understand the Operator’s Manual before using this machine. Danger: Thrown Objects. This machine is capable of throwing objects and debris. Keep bystanders away. Warning: Remove Key Before Servicing.
9 CE Safety Icons Transmission Release Part No. 1730202 173xxxx Attachment Lift Part No. 1730264 Fuel Level Part No. 1730172 1730172 1730264 Ignition Switch Positions Part No. 1722806 Decals Locations Pinch Point When installing or removing the mower deck, do not place hands between mower lift linkage and frame rail.
10 Features & Controls Throttle Contr ol The throttle controls engine speed. Move the throttle forward to increase engine speed and back to decrease engine speed. Always operate at FULL throttle. Choke Close the choke for cold starting. Open the choke once the engine starts.
Rever se Mowing Option (RMO) The Reverse Mowing Option allows for mowing (or use of other PTO driven attachments) while traveling in reverse. If you choose to mow in reverse, turn the RMO key after the PTO is engaged. The L.E.D. light will illuminate, and the operator can then mow in reverse.
12 Features & Controls Figure 2. Engaging the Parking Brake A. Ground Speed Pedals B. Brake Pedal C. Parking Brake Knob D. Cruise Control Knob E. Hourmeter F.
13 Operating the T ractor General Operating Safety Be sure to read all information in the Safety and Operation sections before attempting to operate this unit. Become familiar with all of the controls and how to stop the unit. Adding Fuel To add fuel: 1.
14 Operating the T ractor Stopping The T ractor & Engine 1. Return the ground speed control(s) to neutral. 2. Disengage the PTO and wait for all moving parts to stop. 3. Briggs & Stratton Models: Move the throttle control to SLOW position and turn the ignition key to OFF.
15 Operating the T ractor Mower Dec k Remov al & Installation Removing the Mo wer Deck 1. Park tractor on a hard, level surface such as a concrete floor. Turn off PTO switch and engine, remove the key and apply parking brake. 2. Place wood blocks under the mower deck.
16 Operating the T ractor Attaching a T railer The maximum horizontal drawbar force allowed is 280 Newton. The maximum vertical drawbar force is 160 Newton. This equates to a 250 lbs (113 kg) trailer on a 10 degree hill. Secure the trailer with an appropriately sized clevis pin (A, Figure 8) and clip (B).
17 Regular Maintenance MAINTENANCE SCHEDULE & PR OCEDURES The following schedule should be followed for normal care of your tractor and mower. • = All Models * Refer to engine owner’s manual. Change original engine oil after initial break-in period.
18 Regular Maintenance Battery Maintenance Cleaning the Battery and Cables Service Interval: Every 100 Hours 1. Disconnect the cables from the battery, negative cables first (A, Figure 10) then the cover & positive cables (B). 2. Loosen the wingnut & washer (D).
19 Regular Maintenance Hood Remo val and Installation HOOD REMOVAL 1. Open the hood. 2. Remove the socket and bulbs (A, Figure 12) by twisting the socket counterclockwise and pulling it out of the bezel (B). Repeat on other side. 3. Rock the hood back slightly and lift hood (B, Figure 13) off pivot posts(C).
20 Regular Maintenance Lubrication Service Interval: Every 25 Hours Lubricate the unit at the locations shown in Figures 14- 16 as well as the lubrication points listed. Generally, all moving metal parts should be oiled where contact is made with other parts.
21 Regular Maintenance Figure 17. Rear Axle Hardware A. Key B. Spacer C. Wheel & Hub D. Special Washer E. Small Washer F. E-Clip G. Axle Cap H. Large Washer G B D A E F C Figure 15.
22 Regular Maintenance W ARNING For your personal safety, do not handle the sharp mower blades with bare hands. Careless or improper handling of blades may result in serious injury. W ARNING For your personal safety, blade mounting capscrews must each be installed with two spring washers or a hex washer and spring washer, then securely tightened.
23 Regular Maintenance Chec k & Fill Engine Oil Service Interval: Before each use, and every 8 hours. 1. Turn the engine off, and set the parking brake to PARK. 2. Clean the area around the dip stick (C, Figure 22 or 23). 3. Remove the dip stick (C) and clean it with a paper towel.
24 Regular Maintenance Figure 24. Oil Drain Valve A. Engine Block / Valve Base B. Oil Drain Valve C. Cover D. Nipple A A B B C C D Figure 25. Recommended Engine Oil - Briggs & Stratton Models Use .
25 Regular Maintenance Figure 26. Air Filter Assembly - Briggs & Stratton Twin Cylinder Models A. Knobs B. Air Filter Cover C. Air Filter D. Pre-Cleaner Air Filter & Pre-Cleaner Service BRIGGS & STRATTON TWO CYLINDER MODELS Service Interval: Pre-Cleaner: Every 25 hours or as required.
26 Regular Maintenance 1. 2. 3. Figure 29. Air Filter Assembly - Briggs & Stratton Single Cylinder Models A. Air Filter Latch B. Air Filter Cover A B Air Filter & Pre-Cleaner Service BRIGGS & STRATTON SINGLE CYLINDER MODELS Service Interval: Pre-Cleaner: Every 25 hours or as required.
27 Regular Maintenance Figure 31. Spark Plug Gapping Replace Spark Plug Service Interval: Yearly Spark Plug Gap: .030” (.76mm) Replacement Spark Plug Resistor Spark Plug, Champion RC12YC 1. Stop the engine and allow it to cool. 2. See Figures 31or 32.
28 T roubleshooting, Adjustment, & Service T roub leshooting While normal care and regular maintenance will extend the life of your equipment, prolonged or constant use may eventually require that service be performed to allow it to continue operating properly.
29 T roubleshooting, Adjustment, & Service T r actor T roub leshooting Cont. Tractor drive belt slips. 1. Pulleys or belt greasy or oily. Clean as required. 2. Belt stretched or worn. See Dealer. 3. Idler pulley pivot bracket Remove idler pulley bracket, clean and lubricate.
30 T roubleshooting, Adjustment, & Service Seat Adjustment The seat can be adjusted forward and back. Move the lever (A, Figure 33), position the seat as desired, and release the lever to lock the seat into position.
31 T roubleshooting, Adjustment, & Service PT O clutc h adjustment Check the PTO clutch adjustment after every 250 hours of operation. Also perform the following procedure if the clutch is slipping or will not engage, or if a new clutch has been installed.
32 T roubleshooting, Adjustment, & Service Mower Adjustments Gauge Wheels (Select Models) The mower gauge wheels can be placed in two positions depending on the height of cut. When using higher cutting heights, set the wheels in the lower position.
33 T roubleshooting, Adjustment, & Service W ARNING Before checking mower, shut off PTO and engine, remove the key, and allow all moving parts to stop. Leveling The Mo wer If the cut is uneven, the mower may need leveling. Unequal or improper tire pressure may also cause an uneven cut.
Figure 41. Typical Mower Belt Routing Two Blade Decks A. Idler Pulley Arm B. PTO Pulley (Engine) C. Mower Upstop D. Idler Pulley Belt Guide Left Side of Mower 34 T roubleshooting, Adjustment, & Service Mower Belt Replacement Note: It is not necessary to remove the mower to install a new belt.
35 Specifications ENGINE: 20 HP* Briggs & Stratton Make Briggs & Stratton Model Intek Horsepower 20 @ 3600 rpm Displacement 30.5 Cu. in (582cc) Electrical System 12 Volt, 9 amp. Alternator, Battery: 230 CCA Oil Capacity 64 Oz. (1.9 L) 18.5 HP* Briggs & Stratton Make Briggs & Stratton Model Intek Horsepower 18.
36 Parts & Accessories Replacement P ar ts Replacement parts are available from your authorized dealer. Always use genuine Simplicity Service Parts. T echnical Manuals Additional copies of this manual are available, as well as fully illustrated parts lists.
.
Snapper, INC. 535 Macon Street McDonough, GA 30253 www.snapper.com Briggs & Stratton Yard Power Products Group Copyright © 2008 Briggs & Stratton Corporation Milwaukee, WI USA.
デバイスSnapper LT-200 Seriesの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Snapper LT-200 Seriesをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSnapper LT-200 Seriesの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Snapper LT-200 Seriesの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Snapper LT-200 Seriesで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Snapper LT-200 Seriesを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSnapper LT-200 Seriesの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Snapper LT-200 Seriesに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSnapper LT-200 Seriesデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
