SnapperメーカーLT180H38 IBVの使用説明書/サービス説明書
ページ先へ移動 of 44
Safety Instructions & Operator’s Manual for LAWN TRACTOR HYDROSTATIC DRIVE SERIES I MODELS LT180H33IBV LT180H38IBV MODEL NUMBER EXPLANATION LT 180 H 38 I B V MODEL DESIGNATION ENGINE HP * ENGINE.
2 IMPORTANT SAFETY INSTRUCTIONS WARNING: This pow erful cutting machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply w ith the follow ing SAFETY instructions could result in serious injury or death to the operator or other persons.
3 IMPORTANT SAFETY INSTRUCTIONS PREPARATION (Continued From Previous Page) 6. Check the area to be mow ed and remove all objects such as toys, w ire, rocks, limbs and other objects that could cause injury if thrown by blade or interfere w ith mow ing.
4 IMPORTANT SAFETY INSTRUCTIONS TOWING 1. Tow only w ith a machine that has a hitch designed for tow ing. DO NOT attach tow ed equipment except at the hitch point. 2. Follow the manufacturer’s recommendation for w eight limits for tow ed equipment and tow ing on slopes.
5 TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS ......... 2 - 4 TABLE OF CONTENTS ......................................... 5 SECTION 1 - FAMILIARIZATION .......................... 6 Compone nts ......................................................
6 Section 1 - FAMILIARIZATION COMPONENTS The nomenclature drawings above, illustrate the essential components of the SNAPPER Lawn Tractor. It is recommended that all operators of this equipment become thoroughly familiar with the components and their operation BEFORE OPERATING.
7 Section 2 - OPERATING INSTRUCTIONS 2.1 PRE-START CHECKLIST Make the following checks and perform service as required before each start-up. 2.1.1. Check tires and add air as needed to bring pressure to 12 P.S.I. in front tires and 12 P.S.I. in rear tires.
8 Section 2 - OPERATING INSTRUCTIONS 2.3 STARTING & OPERATION 2.3.1. STARTING ENGINE 1. Take a comfortable position in seat of machine, look around to make sure that the area you are going to mow is clear of people, children and pets.
9 Section 2 - OPERATING INSTRUCTIONS 2.3 STARTING & OPERATION (continued) 2.3.2. STARTING WHEEL DRIVE 1. Shift speed control lever to neutral. 2. Start engine. Refer to Section “STARTING ENGINE”. 3. Release clutch/brake pedal. 4. Slowly shift speed control lever forward for forward motion or to the rear for reverse motion.
10 Section 2 - OPERATING INSTRUCTIONS 2.4 STOPPING 2.4.3. STOPPING MOWER BLADE 1. Stop mower blade by moving blade engagement lever down to the "OFF" position. See Figure 2.11. FIGURE 2.11 WARNING Once blade is disengaged, it should come to a complete stop in 5 seconds or less.
11 Section 2 - OPERATING INSTRUCTIONS 2.6. ROLLING TRACTOR WITH ENGINE OFF 2.6.1. Rolling Hydro Models 1. With engine "OFF", move to rear of tractor. 2. Pull the roll release control all the way out to disengage the hydro transmission. See Figure 2.
12 Section 2 - OPERATING INSTRUCTIONS 2.7. REVERSE LOCKOUT MECHANISM Data indicates that tragi c back-over accidents occur each year. These accidents usually involve unsupervised children.
13 Section 3 - MAINTENANCE 3.1 INTRODUCTION To retain the quality of the Tractor, use genuine SNAPPER replacement parts only. Contact a loca l SNAPPER dealer for parts and service assistance. For the correct part or information for a particular Tractor, always mention the model and serial number.
14 Section 3 - MAINTENANCE 3.2.3. CHECK MOWER BLADE (Continued) FIGURE 3.3 3.2.4. CHECK 33" DECK DRIVE BELT 1. With engine "OFF", move blade engagement lever to "ON". 2. Measure blade cable extension spring. Spring should extend 1" +/-1/8" fo r proper belt tension.
15 Section 3 - MAINTENANCE 3.3.2. MOWER COMPONENTS 1. Check deck drive belt for proper tension. Refer to Section “CHECK DECK DRIVE BELT”. 2. Check blades for sharpness, wear, damage and torque. Refer to Section “MOWER BLADE REPLACEMENT”. 3. Check mower deck for proper levelness.
16 Section 3 - MAINTENANCE 6. Steering Drag Link Lubricate both ends of steering drag link with a small amount of SAE30 oil. See Figure 3.10. FIGURE 3.10 3.3.4. TRACTOR LUBRICATION (Continued From Previous Page) 7. Steering Tie Rod Lubricate both ends of steering tie rod with a small amount of SAE30 oil.
17 Section 3 - MAINTENANCE 3.4 SERVICE - ANNUALLY 3.4.2. FUEL FILTER 1. Service fuel filter as instructed below, on COLD ENGINE ONLY! NOTE: It may be necessary to drain the fuel tank before removing fuel filter to prevent spillage of gasoline. 2. Locate fuel filter.
18 Section 4 - ADJUSTMENT & REPAIR WARNING DO NOT attempt any adjustments, maintenance or service with the engine or blade running. STOP blade. STOP engine. Set brake. Remove key . Remove spark plug w ire from spark plug and secure w ire aw ay from spark plug.
19 Section 4 - ADJUSTMENT & REPAIR WARNING DO NOT attempt any adjustments, maintenance or service with the engine or blade running. STOP blade. STOP engine. Set brake. Remove key . Remove spark plug w ire from spark plug and secure w ire aw ay from spark plug.
20 Section 4 - ADJUSTMENT & REPAIR 4.2.4. ADJUSTING MO WER BLADE – 33” DECK (Continued from prev ious page) FIGURE 4.5 WARNING DO NOT attempt any adjustments, maintenance or service with the engine or blade running. STOP blade. STOP engine. Set brake.
21 Section 4 - ADJUSTMENT & REPAIR WARNING DO NOT attempt any adjustments, maintenance or service with the engine or blade running. STOP blade. STOP engine. Set brake. Remove key . Remove spark plug w ire from spark plug and secure w ire aw ay from spark plug.
22 Section 4 - ADJUSTMENT & REPAIR WARNING DO NOT attempt any adjustments, maintenance or service with the engine or blade running. STOP blade. STOP engine. Set brake. Remove key . Remove spark plug w ire from spark plug and secure w ire aw ay from spark plug.
23 Section 4 - ADJUSTMENT & REPAIR WARNING DO NOT attempt any adjustments, maintenance or service with the engine or blade running. STOP blade. STOP engine. Set brake. Remove key . Remove spark plug w ire from spark plug and secure w ire aw ay from spark plug.
24 Section 4 - ADJUSTMENT & REPAIR WARNING DO NOT attempt any adjustments, maintenance or service with the engine or blade running. STOP blade. STOP engine. Set brake. Remove key . Remove spark plug w ire from spark plug and secure w ire aw ay from spark plug.
25 Section 4 - ADJUSTMENT & REPAIR 4.3.4. TRACTION DRIVE BELT ADJUSTMENT Should a gradual loss of traction be noticed, it may be necessary to adjust the traction drive belt tension. Adjust as follows: 1. Move trac tor to a firm, level surface. 2. Turn engine "OFF".
26 Section 4 - ADJUSTMENT & REPAIR WARNING DO NOT attempt any adjustments, maintenance or service with the engine or blade running. STOP blade. STOP engine. Set brake. Remove key . Remove spark plug w ire from spark plug and secure w ire aw ay from spark plug.
27 Section 4 - ADJUSTMENT & REPAIR WARNING DO NOT attempt any adjustments, maintenance or service with the engine or blade running. STOP blade. STOP engine. Set brake. Remove key . Remove spark plug w ire from spark plug and secure w ire aw ay from spark plug.
28 Section 4 - ADJUSTMENT & REPAIR WARNING DO NOT attempt any adjustments, maintenance or service with the engine or blade running. STOP blade. STOP engine. Set brake. Remove key . Remove spark plug w ire from spark plug and secure w ire aw ay from spark plug.
29 Section 4 - ADJUSTMENT & REPAIR WARNING DO NOT attempt any adjustments, maintenance or service with the engine or blade running. STOP blade. STOP engine. Set brake. Remove key . Remove spark plug w ire from spark plug and secure w ire aw ay from spark plug.
30 Section 4 - ADJUSTMENT & REPAIR WARNING DO NOT attempt any adjustments, maintenance or service with the engine or blade running. STOP blade. STOP engine. Set brake. Remove key . Remove spark plug w ire from spark plug and secure w ire aw ay from spark plug.
31 Section 4 - ADJUSTMENT & REPAIR 4.5 BATTERY NOTE: The battery in this machine is maintenance- free. It has been filled to the proper level w ith acid and is sealed. Do not attempt to open battery. 4.5.1. BATTERY REMOVAL 1. Raise operator's seat.
32 Section 4 - ADJUSTMENT & REPAIR WARNING DO NOT attempt to charge the battery while it is installed on the machine. DO NOT use “BOOST” chargers on the battery. 4.5.5. BATTERY TESTING 1. Remove battery. Refer to section “BATTERY REMOVAL”.
33 Section 4 - ADJUSTMENT & REPAIR AVAILABLE ACCESSORIES The SNAPPER Series H LAWN TRACTOR can be equipped with a va riety of accessories that increase its versatility. The accessories available for each model are listed in the chart below. Contact an authorized SNAPPER dealer for ordering any of the accessories desired.
34 SECTION 5 - ELECTRICAL SYSTEM SCHEMATIC – WIRING HARNESS P.N. 2-8404 LT160H33IBV & LT160H38IBV SCHEMATIC – WIRING HARNESS P.N. 7-3998 LT150H38HKV.
35 TROUBLESHOOTING GUIDE PROBLEM PROBABLE CAUSE CORRECTIVE ACTION Starter Will Not 1. Battery dead. 1. Service battery. Crank Engine 2. Blown fuse. 2. Replace fuse. 3. Electrical connections l oose or corroded. 3. Clean and check connections for good contact.
36 TROUBLESHOOTING GUIDE (Continued From Previous Page) PROBLEM PROBABLE CAUSE CORRECTIVE ACTION Tractor Will Not Move Or Loss Of Traction 1. Speed control handle in the neutral “N” position. 1. Place speed control in desired speed. 2. Roll release control in “ROLL” position.
37 MAINTENANCE SCHEDULE SUBJECT SERVICE TO BE PERFORMED REFERENCE PAGES EACH USE 5 HOURS 25 HOURS 50 HOURS 100 HOURS EACH SEASON Engine Check Oil Level Page 7 X Engine Initial Oil Change Page 13 X Eng.
38 2 YEAR LIMITED WARRANTY For two (2) years from purchase date for the orig inal purchaser's residential, non-commercial use, SNAPPER , through any authorized SNAPPER dealer will replace, free o.
39 PRIMARY MAINTENANCE.
40 PRIMARY MAINTENANCE.
41 PRIMARY MAINTENANCE.
42 PRIMARY MAINTENANCE.
43 SNAPPER PRODUCT REGISTRATION FORM IMPORTANT: KEEP THIS INFORMATION FOR YOUR PERSONAL RECORDS (Complete the following informa tion on your Snapper purchase) Model Number ____________________________.
44 Safety Instructions & Operator’s Manual for LAWN TRACTOR HYDROSTATIC DRIVE SERIES I IMPORTANT Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufactured. The labels on those engines contain very important emissions information and critical safety w arnings.
デバイスSnapper LT180H38 IBVの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Snapper LT180H38 IBVをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSnapper LT180H38 IBVの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Snapper LT180H38 IBVの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Snapper LT180H38 IBVで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Snapper LT180H38 IBVを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSnapper LT180H38 IBVの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Snapper LT180H38 IBVに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSnapper LT180H38 IBVデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
