SnapperメーカーNZMX30614KH, NZMX32734BVの使用説明書/サービス説明書
ページ先へ移動 of 40
Safety Instructions & Operator's Manual for NOTE: Specifications are correct at time of printing and are subject to change without notice. * Actual sustained engine power will likely be lower due to operating limit ations and environment al factors.
2 ! ! IMPORT ANT SAFETY INSTRUCTIONS W ARNING: This powerful cutting machine is capable of amput ating hands and feet and can throw object s that can cause injury and damage! Failure to comply with the following SAFETY instructions could result in serious injury or death to the operator or other persons.
3 ! ! IMPORT ANT SAFETY INSTRUCTIONS PREP ARA TION 1. Read, underst and and follow instructions and warn- ings in this manual and on the machine, engine and att achment s. Know the controls, the safety signs and the proper use of the machine before st arting.
4 ! ! IMPORT ANT SAFETY INSTRUCTIONS OPERA TION (Continued From Previous Page) 7. Blades must be OFF except when cutting grass. Set blades in highest position when mowing over rough ground. 8. Keep hands and feet away from rot ating blades underneath deck.
5 IMPORT ANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . .2-4 T ABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 ST A TEMENT OF USAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 ENGINE POWER RA TING INFORMA TION .
6 Section 1 - F AMILIARIZA TION FIGURE 1.1 1.1 INTRODUCTION This manual has been prepared for the operator’s of the SNAPPER MID MOUNT Z-RIDER. It s purpose, aside from recommending standard operating procedures and routine service requirements, is to promote SAFETY through the use of accepted operating practices.
7 Section 2 - SAFETY MESSAGES AND SYMBOLS DANGER ! ROT A TING P ARTS KEEP AW A Y FROM MOVING P ARTS P ARKING BRAKE LEVER OPERA TION MOTION CONTROL LEVER OPERA TION WEAR HEARING PROTECTION W ARNING ! A.
FUEL GAUGE (2) CONTROL P ANEL IDENTIFICA TION DANGER! ROT A TING BLADES KEEP CHILDREN AND OTHERS OUT OF MOWING AREA FUEL T ANK SELECT IGNITION SWITCH STOP RUN ST ART 8 Section 2 - SAFETY MESSAGES AND .
9 Section 2 - SAFETY MESSAGES AND SYMBOLS ROLL BAR PROTECTIVE STRUCTURE DECALS CAUTION! SPRING LOADED MECHANISM Cutting Hazard Fans rotate while engine is running. Keep away while engine is running. W ARNING A TTENCION Peligro de corte Los ventiladores giran mientras el motor esta funcionando.
10 Section 3 - OPERA TING INSTRUCTIONS 3.1 PRE-ST ART CHECK LIST Make the following checks and perform the service required before each start-up. 3.1.1. Check tires and add or release air as needed to bring pressure to 12 psi in drive tires. Pressure in front caster wheels should be 25 psi.
11 Section 3 - OPERA TING INSTRUCTIONS Section 3 - OPERA TING INSTRUCTIONS ROLL RELEASE: T o roll the machine without the engine running, pressure within the hydraulic pump s must be released. There is a hydraulic pressure relief valve on the upper side of each pump that is used to release the pressure.
12 Section 3 - OPERA TING INSTRUCTIONS Section 3 - OPERA TING INSTRUCTIONS 3.2.1. ST ARTING ENGINE NOTE: If after 5 seconds of cranking the engine does not start, release the key . Attempt starting again af ter waiting for approximately 20 seconds. 7.
13 Section 3 - OPERA TING INSTRUCTIONS 3.3 CUTTING HEIGHT ADJUSTMENT 1. Depress deck lift pedal fully to lock deck in trans- port position. See Figure 3.9. 2. Insert stop pin to desired cutting height. See Figure 3.10. 3. Depress deck lift pedal while flipping back transport lever , and slowly release pedal to lower deck.
14 Section 3 - OPERA TING INSTRUCTIONS 3.4.2. STOPPING MACHINE 1. Return motion control levers to the neutral position & the neutral lock position. IMPORT ANT : Operator must use hand assistance to bring both motion control levers to the neutral position & the neutral lock position.
15 Section 3 - OPERA TING INSTRUCTIONS Section 4 - MAINTENANCE 4.1 INTRODUCTION T o retain the quality of the SNAPPER mower , use gen- uine SNAPPER replacement part s only .
16 Section 3 - OPERA TING INSTRUCTIONS Section 4 - MAINTENANCE 4.2.3. CHECK MOWER DRIVE BEL T 1. Lower deck to lowest setting. 2. Remove footrest. See Figure 4.3. 3. Removal of footrest will allow access to deck belt. 4. Check the belt tension. The idler pulleys and springs provide proper tension and require no adjust- ments.
17 Section 3 - OPERA TING INSTRUCTIONS 4.5 ANNUALL Y (END OF EACH SEASON) Perform all maintenance as described in Section "AFTER EVERY 25 OPERA TING HOURS". Refer to Section "Service Schedule". 4.5.1. ENGINE Service engine according to engine owner's manual.
18 Section 3 - OPERA TING INSTRUCTIONS Section 4 - MAINTENANCE 4.5 ANNUALL Y (END OF EACH SEASON) (Continued from previous Page) 4.5.2. FUEL FIL TER Service fuel filter as instructed below . T urn key to "OFF" position. Engine MUST be stopped and MUST be cold before removing filter .
19 Section 3 - OPERA TING INSTRUCTIONS Section 4 - MAINTENANCE 4.6 DECK REMOV AL (Continued from previous p age) 6. Remove inside nuts that secure fittings to front lift arms. See Figure 4.10. 7. Remove inside nuts that secure eyebolt s to rear lift arms.
20 Section 3 - OPERA TING INSTRUCTIONS 10. If wheel(s) are rotating, loosen the hydro pump activation assembly retaining screw . Move activation assembly forward or rearward to stop rotation of wheel. Retighten retaining screw . Repeat this step for other hydro pump.
21 Section 3 - OPERA TING INSTRUCTIONS Section 5 - ADJUSTMENTS & REP AIR 5.1 NEUTRAL POSITION ADJUSTMENTS (Continued From Previous Page) 12. With motion control levers remaining in the neutral lock position, See Figure 3.7, hold connecting rod up to the activation assembly and check length of rod.
22 Section 3 - OPERA TING INSTRUCTIONS Section 5 - ADJUSTMENTS & REP AIR 5.2.1. MOWER DECK ADJUSTMENT (LEVELNESS) SIDE to SIDE and FRONT to REAR 8. Loosen the bottom nuts that secure both rear deck support eyebolts. Adjust top nuts until eyebolts are tight, then tighten bottom nuts securely .
23 Section 3 - OPERA TING INSTRUCTIONS Section 5 - ADJUSTMENTS & REP AIR 5.3 TRACTION BEL T TENSION The traction drive belt tension does not require adjustment. If the belts are slipping, they will have to be replaced. 5.4 TRACTION BEL T REPLACEMENT 1.
24 Section 3 - OPERA TING INSTRUCTIONS Section 5 - ADJUSTMENTS & REP AIR 5.6 TRACKING ADJUSTMENT If the machine does not track straight when the Motion Control Levers are in the maximum forward speed position, perform the following adjustment. Rear tire pressure must be set to 12 PSI before making this adjustment.
25 Section 3 - OPERA TING INSTRUCTIONS Section 5 - ADJUSTMENTS & REP AIR 5.8 ENGINE ADJUSTMENTS & REP AIR Refer to the engine owner's manual for engine adjust- ments and/or rep airs. 5.9 MOWER BLADE REPLACEMENT 5.9.1. BLADE WEAR LIMITS 1.
26 Section 3 - OPERA TING INSTRUCTIONS Section 5 - ADJUSTMENTS & REP AIR 5.10 BA TTER Y NOTE: In order to raise operator set to access battery comp artment, seat must be in rearmost position. 5.10.1. BA TTER Y REMOV AL 1. Slide terminal cover away from positive terminal.
27 Section 3 - OPERA TING INSTRUCTIONS Section 5 - ADJUSTMENTS & REP AIR 5.10.4. BA TTER Y TESTING 1. Remove battery . Refer to Section "BA TTERY REMOV AL". 2. Using a voltmeter , check the battery's state of charge by comparing the voltmeter reading with the chart below .
28 Section 3 - OPERA TING INSTRUCTIONS Section 5 - ADJUSTMENTS & REP AIR 5.1 1 HYDRAULIC SYSTEM, PURGING After replacing or rep airing hydraulic system compo- nents, one or both of the wheel drives may not pull properly . This is likely to be caused by air entrapped in the system.
29 Section 3 - OPERA TING INSTRUCTIONS TROUBLESHOOTING PROBLEM PROBABLE CAUSE CORRECTIVE ACTION St arter Will Not Crank Engine 1. Battery dead. 1. Service battery . 2. Blown fuse. 2. Replace fuse. 3. Electrical connections loose or corroded. 3. Clean and check connections for good contact.
30 Section 3 - OPERA TING INSTRUCTIONS TROUBLESHOOTING PROBLEM PROBABLE CAUSE CORRECTIVE ACTION Machine Will Not Move Loss Of T raction 1. Motion Control Levers in the neutral "N" position. 1. Move Motion Controls to desired speed position. 2.
31 Section 3 - OPERA TING INSTRUCTIONS SER VICE SCHEDULE ITEM SERVICE PERFORMED REF . NUMBER EACH USE 5 HRS 25 HRS 50 HRS 100 HRS EACH SEASON Engine Oil Check Oil Level Page 10 X Initial Oil Change Pa.
32 2 YEAR LIMITED W ARRANTY For two (2) years from purchase date for the original purchaser's use, SNAPPER , through any authorized SNAPPER dealer will replace, free of charge (except for taxes where applicable), any p art or part s found upon examination by the factory at McDonough, Georgia, to be defective in material or workmanship or both.
33 PRIMAR Y MAINTENANCE.
34 PRIMAR Y MAINTENANCE.
35 PRIMAR Y MAINTENANCE.
36 PRIMAR Y MAINTENANCE.
37 SNAPPER PRODUCT REGISTRA TION FORM IMPOR T ANT : KEEP THIS INFORMA TION FOR YOUR PERSONAL RECORDS (Complete the following information on your Snapper pur chase) Model Number________________________.
38 NOTES.
39 NOTES.
40 Safety Instructions & Operator's Manual for IMPORT ANT Snapper product s are built using engines that meet or exceed all applicable emissions requirement s on the date manufactured. The labels on those engines cont ain very import ant emissions information and critical safety warnings.
デバイスSnapper NZMX30614KH, NZMX32734BVの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Snapper NZMX30614KH, NZMX32734BVをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSnapper NZMX30614KH, NZMX32734BVの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Snapper NZMX30614KH, NZMX32734BVの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Snapper NZMX30614KH, NZMX32734BVで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Snapper NZMX30614KH, NZMX32734BVを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSnapper NZMX30614KH, NZMX32734BVの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Snapper NZMX30614KH, NZMX32734BVに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSnapper NZMX30614KH, NZMX32734BVデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
