SnapperメーカーP217019BVEの使用説明書/サービス説明書
ページ先へ移動 of 32
Safety Instructions & Operator's Manual for 21" STEEL DECK WALK MOWERS SERIES 19 MODELS 2167519B P2167519B P217019BV P217019BVE P216019KWV MODEL NUMBER EXPLANATION SELF-PROPELLED CUTTING.
IMPORTANT SAFETY INSTRUCTIONS WARNING: This powerful cutting machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply with the following SAFETY instructions could result in serious injury or death to the operator or other persons.
IMPORTANT SAFETY INSTRUCTIONS SAFE HANDLING OF GASOLINE (Continued From Previous Page) 3. DO NOT remove fuel cap or add fuel with the engine running. Allow the engine to cool before refueling.
IMPORTANT SAFETY INSTRUCTIONS MAINTENANCE AND STORAGE (Continued From Previous Page) 9. Mower blades are sharp and can cut. Wrap the blades or wear heavy leather gloves and use CAUTION when handling them. 10. DO NOT test for spark by grounding spark plug next to spark plug hole; spark plug could ignite gas exiting engine.
TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS ...................................................................... 2 - 4 TABLE OF CONTENTS ...................................................................................................... 5 SECTION 1 - FAMILIARIZATION .
Section 1 - FAMILIARIZATION / ENGINE SPEED CONTROL ROPE / START HANDLE WHEEL DRIVE CONTROL GRASS BAG REAR HEIGHT ADJUSTMENT LATCH BLADE CONTROL / GRASS BAG ADAPTER GROUND SPEED CONTROL FUEL FILL FIGURE 1.
Section 2 -OPERATING INSTRUCTIONS 2.1 PRE-START CHECK LIST Make the following checks and perform the service required before each start-up. 2.1.1. Check guards, deflectors, grass bag, adapter and covers to make sure all are in place and securely tightened.
Section 2 -OPERATING INSTRUCTIONS 2.2 STARTING & OPERATION 2.3 2.2.1. ENGINE & BLADE (Kawasaki Engine) 1. Make sure fuel valve on engine is open. See Figure 2.5. STOPPING Stop forward motion of mower by releasing the wheel drive control. Stop engine and blade by releasing the blade control.
Section 2 -OPERATING INSTRUCTIONS 2. Set all wheels at the same cutting height. The highest cutting position is Notch 7. The lowest cutting position is Notch 1. See Figures 2.8 & 2.9. STEP la (Kawasaki only): Attach Bag Adapter Standoff between rope guide pulley assembly and engine recoil.
Section 2 -OPERATING INSTRUCTIONS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
Section 2 -OPERATING INSTRUCTIONS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
Section 3- MAINTENANCE 3.1 INTRODUCTION To retain the quality of the mower, use genuine SNAPPER replacement parts only. Contact a local SNAPPER dealer for parts and service assistance. For the correct part or information for a particular mower, always mention model and serial number.
Section 3- MAINTENANCE WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running.STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running.STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running.STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running.STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
Section 4 - REPAIR & ADJUSTMENTS 4.5. BATTERY SERVICE 4.5.1. NEW BATTERY PREPARATION 1. Remove battery from carton. 2. Place battery in a well ventilated area on a level non-concrete surface. 3. Remove battery cell caps. Fill cells as required with electrolyte (supplied with battery) to proper level.
PROBLEM Engine Will Not Start Using Recoil Starter Engine Stalls or Stops After Running Engine Loses Power Excessive Vibration Mower Will Not Move Loss Of Traction (Self-Propelled Models) Cutting Grass Improperly Poor Grass Discharge Oil Leaking TROUBLESHOOTING PROBABLE CAUSE 1• Fuel tank empty• 2• Engine needs choking or priming.
SERVICE SCHEDULE ITEM Engine Oil SERVICE PERFORMED REF. Check Oil Level Page 7 EACH 5 25 USE HRS HRS X 5O HRS 100 HRS Initial Oil Change Page 12 X Periodic Oil Change Page 13 X* Air Pre-Cleaner Clean .
2 YEAR LIMITED WARRANTY For two (2) years from purchase date for the original purchaser's residential, non-commercial use, SNAPPER, through any authorized SNAPPER dealer will replace, free of cha.
PRIMARY MAINTENANCE III illustration of engine & how Q It: can protect" v Snapper uses the best avail- ab!e engines and components in their products In; order to care Is easentfai In prolonging engine life.
PRIMARY MAINTENANCE men_ the air available to your S_ppar engine Is" heavily eatura_ wl_ air- quickly mln an engine, manufactumre equip their engines with extremely _clent air cleanere to As the .
PRIMARY MAINTENANCE Generelly_ wash foam-type filters in a dlshwashlng detergent and water solution. Rinse and wring dry, then saturate with oil and squeeze out excess, Failure to re-off this type fitter will ruin the Clean paper elements by tapping lightly.
PRIMARY MAINTENANCE On 4_yle engines with an otl level plug, don't be fooled into thinking the engine has sufficient lubricating oll if you can see "some" brought up to the point top of the fill hole. On 2-cycle englnee, lubrication must be provided by an exact mixture of gasoline and 2-cycte air--led engine oiL A 2.
SNAPPER PRODUCT REGISTRATION FORM IMPORTANT: KEEP THIS INFORMATION FOR YOUR PERSONAL RECORDS (Complete the following information on your Snapper purchase) Model Number Serial Number Date of Purchase Retailer Retailer's Phone Number It is very important that you register your purchase with Snapper to ensure warranty coverage.
NOTES 30.
NOTES 31.
Safety Instructions & Operator's Manual for 21" STEEL DECK WALK BEHIND MOWERS SERIES 19 IMPORTANT Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufactured. The labels on those engines contain very important emissions information and critical safety warnings.
デバイスSnapper P217019BVEの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Snapper P217019BVEをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSnapper P217019BVEの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Snapper P217019BVEの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Snapper P217019BVEで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Snapper P217019BVEを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSnapper P217019BVEの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Snapper P217019BVEに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSnapper P217019BVEデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
