SnapperメーカーSERIES 16 250816Bの使用説明書/サービス説明書
ページ先へ移動 of 112
Safety Instructions & Operator's Manual for REAR ENGINE RIDING MOWER SERIES 16 MODELS 250816B N250816B 250816BE N250816BE 281016BE N281016BE 301016BE 301216BE 331416BVE 331416KVE PRECIX BODYI.
IMPORTANT SAFETY INSTRUCTIONS WARNING: This powerful cutting machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply with the following SAFETY instructions could result in sedous injury or death to the operator or other persons.
Section 1 - FAMILIARIZATION FUEL VENT TANK REAR BUMPER FUEL FILLER STEERING WHEEL F OPERATOR'S SEAT TRANSMISSION SHIFT; PANEL (See Inset) DECK LIFT LEVER CLUTCH/BRAKE PEDAL CHUTE DEFLECTOR CONTROL PANEL IGNITION SWITCH ENGINE SPEED CQ_TROL BRAKE LEVER 1 I I MOWER DECK I I LEVER FIGURE 1.
Section 2 -OPERATING INSTRUCTIONS 2.1 PRE-START CHECK UST 2.2 Make the following checks and perform the service required before each start-up. 2.1.1. Check tires and add or release air as needed to bring pressure to 15 psi in front and 10 psi in rear tires.
Section 2 - OPERATING INSTRUCTIONS 2.3 STARTING & OPERATION 2.3.1 ENGINE (ELECTRIC START) IMPORTANT: When the ignition key is turned to "START", the engine will turn over, but will not start unless the Clutch/Brake pedal is pressed all the way down, the Blade Lever is in the "OFF" position (See Figure 2.
Section 2- OPERATING INSTRUCTIONS 2.3.1 ENGINE (ELECTRIC START) (Continued) 8. Should the battery be too weak to start the engine, use the instructions shown below, 2.3.2., ENGINE (MANUAL START) to manually start the electric start en- gines. 9. On Model 331416BVE, the engine is equipped with a fuel shut-off solenoid.
Section 2 - OPERATING INSTRUCTIONS /_ CAUTION /'_ Before leaving the Rear Engine Rider with the engine running, STOP the blade, shift to neutral and engage the park brake. 2.4 STOPPING 2.4.1. ENGINE 1. Stop engine by turning key to the "OFF" position.
Section 2 - OPERATING INSTRUCTIONS 2.4.4. PARK BRAKE (Continued) 2. Release park brake by pushing down on the Clutch/Brake Pedal to release park brake lever. See Figure 2.15. PUSH CLUTCWBRAKE PEDAL ALL THE WAY DOWN 2.4.6. WHEEL DRIVE 1. With engine running, adjust engine speed con- trol to "FAST" position.
Section 3 - MAINTENANCE 3.1 INTRODUCTION To retain the quality of the Rear Engine Rider, use genuine SNAPPER replacement parts only. Contact a local SNAPPER dealer for parts and service assistance. For the correct part or information for a particular Rear Engine Riding Mower, always mention the model and sedal number.
Section 3 - MAINTENANCE 3.2.3. CHECK MOWER DRIVE BELT 1. Drive Belt Cover Removal a. Lower deck to lowest setting. b. Remove four self-tapping screws, two on each side of mower drive belt cover. See Figure 3.3. c. Slide cover back and rotate out on left side of mower deck.
Section 3 - MAINTENANCE 3.3.2. MOWER COMPONENTS (Continued) d. Close vent on fuel filler cap. e. Carefully stand Rear Engine Rider on rear bumper. f. Clean underside of mower deck, removing all accumulation of grass clippings and debds. g. Lower Rear Engine Rider to ground and clean top of deck, removing all grass clippings and debris.
Section 3 - MAINTENANCE DIFFERENTIAL . I FIGURE 3.9 Chain Case a. Check fill/level plug for damage. If signs of wear or cracks are visible, replace plug with new plug. See Figure 3.10. b. To check lubricant in chain case, remove fill/level plug and look for lubricant on the internal components of the chain case.
Section 3 - MAINTENANCE 3.5 3.6 EVERY TWO YEARS 3.5.3. Transmission shift lever and detent. 3.5.4. Clutch disc. 3.5.5. Clutch Yoke (See Figure 4.18 on Page 18). 3.5.6. Mower deck linkage and pivot areas. STORAGE (OUT OF SEASON) If desired, the Rear Engine Rider can be stored on the rear bumper.
Section 4 - ADJUSTMENTS & REPAIR Before performing any service or maintenance I procedures, always remove key from ignition I switch, remove spark plug wire from spark plug and I secure spark plug wire away from spark plug.
Section 4 - ADJUSTMENTS & REPAIR CAUTION Before performing any service or maintenance procedures, always remove key from ignition switch, remove spark plug wire from spark plug and secure spark plug wire away from spark plug. 4.2.2. BLADE BRAKE ADJUSTMENT 1.
Section 4 - ADJUSTMENTS & REPAIR LOOSEN SHOULDER BOLT 4.2.4. MOWER DECK ADJUSTMENT (LEVELNESS) 1. Side-To-Side Before making deck leveling adjustments, check the tire pressure. Front tires 15 psi, rear tires 10 psi. If tires are properly inflated and mowing is still uneven, adjust side-to-side deck levelness as follows: a.
Section 4 - ADJUSTMENTS & REPAIR 4.2.5. MOWER DECK TIMING ROD ADJUSTMENT The mower deck timing rod is pre-adjusted at the factory. It is set to maintain the deck in the same attitude through all heights of cut. If suspecting the timing rod requires adjustment, contact an authorized SNAPPER dealer for service.
Section 4 - ADJUSTMENTS & REPAIR CAUTION Before attempting any adjustments or repairs, stop the engine, remove the key, remove the spark plug wire from the spark plug, and secure spark plug wire away from spark plug. 1. Follow procedures for standing Rear Engine Rider on rear bumper.
Section 4 - ADJUSTMENTS & REPAIR HOUSING CABLE COTTER-, 3. Measure the distance between end of clutch/brake cable and bottom of housing. Measurement should be no less than 112" and no greater than 3/4". See inset, Figure 4.18. CHAIN- CASE HOUSING COTTER- PIN FIGURE 4.
Section 4 - ADJUSTMENTS & REPAIR 3. Inspect condition of blade. Refer to Figure 4.20. 4. If blade is in good condition, sharpen at 22 to 28 degrees.
Section 4 -ADJUSTMENTS & REPAIR 4.6.2. BELT REPLACEMENT (Continued) 9. Adjust bait guide. See Figure 4.25 for proper bait-to-belt guide clearances. 10. Check mower drive belt tension and adjust if necessary. Refer to 4.2.1., MOWER DRIVE BELT ADJUSTMENT on Page 13.
Section 4 - ADJUSTMENTS & REPAIR CAUTION The electrolyte (acid) produces a highly explosive gas. Keep all sparks, flame and fire away from area when charging battery or when handling electrolyte or battery. Electrolyte (acid) is a highly corrosive liquid.
Section 4 - ADJUSTMENTS & REPAIR 4.6.5. BATTERY TESTING Methods of Checking Battery Condition State of Charcje 100% Charged w/Sulfate Stop 100% Charged 75% Charged 50% Charged 25% Charged 0% Charcjed Syringe Hydrometer 1.280 1.265 1.210 1.160 1.120 Less than 1.
MAINTENANCE SCHEDULE SUBJECT Engine Engine Engine Air Pre-Cleaner Air Cleaner Spark Plug Fuel Filter Engine Cooling System Battery Battery Tires Drive Belts Mower Blades Mower Deck Lubrication Points .
SNAPPER. 5 - 2 YEAR LIMITED WARRANTY COMPONENT PARTS - 5 YEARS For five (5) years from purchase date for original purchaser's residential non-commercial _' use, Snapper, through any Snapper dealer will replace free of charge any part or parts found upon examination by the factory to be defective in material or workmanship or both.
SERVICE NOTES i.
SERVICE NOTES.
Safety Instructions & Operator's Manual for • REAR ENGINE RIDING MOWER SERIES 16 The engine exhaust from this product contains chemicals known to the State of I AWARNING: California to cause cancer, birth defects or other reproductive harm.
Safety Instructions & Operator's Manual for REAR ENGINE RIDING MOWER SERIES 16 MODELS 250816B N250816B 250816BE N250816BE 281016BE N281016BE 301016BE 301216BE 331416BVE 331416KVE PRECIX BODYI.
IMPORTANT SAFETY INSTRUCTIONS WARNING: This powerful cutting machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply with the following SAFETY instructions could result in sedous injury or death to the operator or other persons.
Section 1 - FAMILIARIZATION FUEL VENT TANK REAR BUMPER FUEL FILLER STEERING WHEEL F OPERATOR'S SEAT TRANSMISSION SHIFT; PANEL (See Inset) DECK LIFT LEVER CLUTCH/BRAKE PEDAL CHUTE DEFLECTOR CONTROL PANEL IGNITION SWITCH ENGINE SPEED CQ_TROL BRAKE LEVER 1 I I MOWER DECK I I LEVER FIGURE 1.
Section 2 -OPERATING INSTRUCTIONS 2.1 PRE-START CHECK UST 2.2 Make the following checks and perform the service required before each start-up. 2.1.1. Check tires and add or release air as needed to bring pressure to 15 psi in front and 10 psi in rear tires.
Section 2 - OPERATING INSTRUCTIONS 2.3 STARTING & OPERATION 2.3.1 ENGINE (ELECTRIC START) IMPORTANT: When the ignition key is turned to "START", the engine will turn over, but will not start unless the Clutch/Brake pedal is pressed all the way down, the Blade Lever is in the "OFF" position (See Figure 2.
Section 2- OPERATING INSTRUCTIONS 2.3.1 ENGINE (ELECTRIC START) (Continued) 8. Should the battery be too weak to start the engine, use the instructions shown below, 2.3.2., ENGINE (MANUAL START) to manually start the electric start en- gines. 9. On Model 331416BVE, the engine is equipped with a fuel shut-off solenoid.
Section 2 - OPERATING INSTRUCTIONS /_ CAUTION /'_ Before leaving the Rear Engine Rider with the engine running, STOP the blade, shift to neutral and engage the park brake. 2.4 STOPPING 2.4.1. ENGINE 1. Stop engine by turning key to the "OFF" position.
Section 2 - OPERATING INSTRUCTIONS 2.4.4. PARK BRAKE (Continued) 2. Release park brake by pushing down on the Clutch/Brake Pedal to release park brake lever. See Figure 2.15. PUSH CLUTCWBRAKE PEDAL ALL THE WAY DOWN 2.4.6. WHEEL DRIVE 1. With engine running, adjust engine speed con- trol to "FAST" position.
Section 3 - MAINTENANCE 3.1 INTRODUCTION To retain the quality of the Rear Engine Rider, use genuine SNAPPER replacement parts only. Contact a local SNAPPER dealer for parts and service assistance. For the correct part or information for a particular Rear Engine Riding Mower, always mention the model and sedal number.
Section 3 - MAINTENANCE 3.2.3. CHECK MOWER DRIVE BELT 1. Drive Belt Cover Removal a. Lower deck to lowest setting. b. Remove four self-tapping screws, two on each side of mower drive belt cover. See Figure 3.3. c. Slide cover back and rotate out on left side of mower deck.
Section 3 - MAINTENANCE 3.3.2. MOWER COMPONENTS (Continued) d. Close vent on fuel filler cap. e. Carefully stand Rear Engine Rider on rear bumper. f. Clean underside of mower deck, removing all accumulation of grass clippings and debds. g. Lower Rear Engine Rider to ground and clean top of deck, removing all grass clippings and debris.
Section 3 - MAINTENANCE DIFFERENTIAL . I FIGURE 3.9 Chain Case a. Check fill/level plug for damage. If signs of wear or cracks are visible, replace plug with new plug. See Figure 3.10. b. To check lubricant in chain case, remove fill/level plug and look for lubricant on the internal components of the chain case.
Section 3 - MAINTENANCE 3.5 3.6 EVERY TWO YEARS 3.5.3. Transmission shift lever and detent. 3.5.4. Clutch disc. 3.5.5. Clutch Yoke (See Figure 4.18 on Page 18). 3.5.6. Mower deck linkage and pivot areas. STORAGE (OUT OF SEASON) If desired, the Rear Engine Rider can be stored on the rear bumper.
Section 4 - ADJUSTMENTS & REPAIR Before performing any service or maintenance I procedures, always remove key from ignition I switch, remove spark plug wire from spark plug and I secure spark plug wire away from spark plug.
Section 4 - ADJUSTMENTS & REPAIR CAUTION Before performing any service or maintenance procedures, always remove key from ignition switch, remove spark plug wire from spark plug and secure spark plug wire away from spark plug. 4.2.2. BLADE BRAKE ADJUSTMENT 1.
Section 4 - ADJUSTMENTS & REPAIR LOOSEN SHOULDER BOLT 4.2.4. MOWER DECK ADJUSTMENT (LEVELNESS) 1. Side-To-Side Before making deck leveling adjustments, check the tire pressure. Front tires 15 psi, rear tires 10 psi. If tires are properly inflated and mowing is still uneven, adjust side-to-side deck levelness as follows: a.
Section 4 - ADJUSTMENTS & REPAIR 4.2.5. MOWER DECK TIMING ROD ADJUSTMENT The mower deck timing rod is pre-adjusted at the factory. It is set to maintain the deck in the same attitude through all heights of cut. If suspecting the timing rod requires adjustment, contact an authorized SNAPPER dealer for service.
Section 4 - ADJUSTMENTS & REPAIR CAUTION Before attempting any adjustments or repairs, stop the engine, remove the key, remove the spark plug wire from the spark plug, and secure spark plug wire away from spark plug. 1. Follow procedures for standing Rear Engine Rider on rear bumper.
Section 4 - ADJUSTMENTS & REPAIR HOUSING CABLE COTTER-, 3. Measure the distance between end of clutch/brake cable and bottom of housing. Measurement should be no less than 112" and no greater than 3/4". See inset, Figure 4.18. CHAIN- CASE HOUSING COTTER- PIN FIGURE 4.
Section 4 - ADJUSTMENTS & REPAIR 3. Inspect condition of blade. Refer to Figure 4.20. 4. If blade is in good condition, sharpen at 22 to 28 degrees.
Section 4 -ADJUSTMENTS & REPAIR 4.6.2. BELT REPLACEMENT (Continued) 9. Adjust bait guide. See Figure 4.25 for proper bait-to-belt guide clearances. 10. Check mower drive belt tension and adjust if necessary. Refer to 4.2.1., MOWER DRIVE BELT ADJUSTMENT on Page 13.
Section 4 - ADJUSTMENTS & REPAIR CAUTION The electrolyte (acid) produces a highly explosive gas. Keep all sparks, flame and fire away from area when charging battery or when handling electrolyte or battery. Electrolyte (acid) is a highly corrosive liquid.
Section 4 - ADJUSTMENTS & REPAIR 4.6.5. BATTERY TESTING Methods of Checking Battery Condition State of Charcje 100% Charged w/Sulfate Stop 100% Charged 75% Charged 50% Charged 25% Charged 0% Charcjed Syringe Hydrometer 1.280 1.265 1.210 1.160 1.120 Less than 1.
MAINTENANCE SCHEDULE SUBJECT Engine Engine Engine Air Pre-Cleaner Air Cleaner Spark Plug Fuel Filter Engine Cooling System Battery Battery Tires Drive Belts Mower Blades Mower Deck Lubrication Points .
SNAPPER. 5 - 2 YEAR LIMITED WARRANTY COMPONENT PARTS - 5 YEARS For five (5) years from purchase date for original purchaser's residential non-commercial _' use, Snapper, through any Snapper dealer will replace free of charge any part or parts found upon examination by the factory to be defective in material or workmanship or both.
SERVICE NOTES i.
SERVICE NOTES.
Safety Instructions & Operator's Manual for • REAR ENGINE RIDING MOWER SERIES 16 The engine exhaust from this product contains chemicals known to the State of I AWARNING: California to cause cancer, birth defects or other reproductive harm.
Safety Instructions & Operator's Manual for REAR ENGINE RIDING MOWER SERIES 16 MODELS 250816B N250816B 250816BE N250816BE 281016BE N281016BE 301016BE 301216BE 331416BVE 331416KVE PRECIX BODYI.
IMPORTANT SAFETY INSTRUCTIONS WARNING: This powerful cutting machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply with the following SAFETY instructions could result in sedous injury or death to the operator or other persons.
Section 1 - FAMILIARIZATION FUEL VENT TANK REAR BUMPER FUEL FILLER STEERING WHEEL F OPERATOR'S SEAT TRANSMISSION SHIFT; PANEL (See Inset) DECK LIFT LEVER CLUTCH/BRAKE PEDAL CHUTE DEFLECTOR CONTROL PANEL IGNITION SWITCH ENGINE SPEED CQ_TROL BRAKE LEVER 1 I I MOWER DECK I I LEVER FIGURE 1.
Section 2 -OPERATING INSTRUCTIONS 2.1 PRE-START CHECK UST 2.2 Make the following checks and perform the service required before each start-up. 2.1.1. Check tires and add or release air as needed to bring pressure to 15 psi in front and 10 psi in rear tires.
Section 2 - OPERATING INSTRUCTIONS 2.3 STARTING & OPERATION 2.3.1 ENGINE (ELECTRIC START) IMPORTANT: When the ignition key is turned to "START", the engine will turn over, but will not start unless the Clutch/Brake pedal is pressed all the way down, the Blade Lever is in the "OFF" position (See Figure 2.
Section 2- OPERATING INSTRUCTIONS 2.3.1 ENGINE (ELECTRIC START) (Continued) 8. Should the battery be too weak to start the engine, use the instructions shown below, 2.3.2., ENGINE (MANUAL START) to manually start the electric start en- gines. 9. On Model 331416BVE, the engine is equipped with a fuel shut-off solenoid.
Section 2 - OPERATING INSTRUCTIONS /_ CAUTION /'_ Before leaving the Rear Engine Rider with the engine running, STOP the blade, shift to neutral and engage the park brake. 2.4 STOPPING 2.4.1. ENGINE 1. Stop engine by turning key to the "OFF" position.
Section 2 - OPERATING INSTRUCTIONS 2.4.4. PARK BRAKE (Continued) 2. Release park brake by pushing down on the Clutch/Brake Pedal to release park brake lever. See Figure 2.15. PUSH CLUTCWBRAKE PEDAL ALL THE WAY DOWN 2.4.6. WHEEL DRIVE 1. With engine running, adjust engine speed con- trol to "FAST" position.
Section 3 - MAINTENANCE 3.1 INTRODUCTION To retain the quality of the Rear Engine Rider, use genuine SNAPPER replacement parts only. Contact a local SNAPPER dealer for parts and service assistance. For the correct part or information for a particular Rear Engine Riding Mower, always mention the model and sedal number.
Section 3 - MAINTENANCE 3.2.3. CHECK MOWER DRIVE BELT 1. Drive Belt Cover Removal a. Lower deck to lowest setting. b. Remove four self-tapping screws, two on each side of mower drive belt cover. See Figure 3.3. c. Slide cover back and rotate out on left side of mower deck.
Section 3 - MAINTENANCE 3.3.2. MOWER COMPONENTS (Continued) d. Close vent on fuel filler cap. e. Carefully stand Rear Engine Rider on rear bumper. f. Clean underside of mower deck, removing all accumulation of grass clippings and debds. g. Lower Rear Engine Rider to ground and clean top of deck, removing all grass clippings and debris.
Section 3 - MAINTENANCE DIFFERENTIAL . I FIGURE 3.9 Chain Case a. Check fill/level plug for damage. If signs of wear or cracks are visible, replace plug with new plug. See Figure 3.10. b. To check lubricant in chain case, remove fill/level plug and look for lubricant on the internal components of the chain case.
Section 3 - MAINTENANCE 3.5 3.6 EVERY TWO YEARS 3.5.3. Transmission shift lever and detent. 3.5.4. Clutch disc. 3.5.5. Clutch Yoke (See Figure 4.18 on Page 18). 3.5.6. Mower deck linkage and pivot areas. STORAGE (OUT OF SEASON) If desired, the Rear Engine Rider can be stored on the rear bumper.
Section 4 - ADJUSTMENTS & REPAIR Before performing any service or maintenance I procedures, always remove key from ignition I switch, remove spark plug wire from spark plug and I secure spark plug wire away from spark plug.
Section 4 - ADJUSTMENTS & REPAIR CAUTION Before performing any service or maintenance procedures, always remove key from ignition switch, remove spark plug wire from spark plug and secure spark plug wire away from spark plug. 4.2.2. BLADE BRAKE ADJUSTMENT 1.
Section 4 - ADJUSTMENTS & REPAIR LOOSEN SHOULDER BOLT 4.2.4. MOWER DECK ADJUSTMENT (LEVELNESS) 1. Side-To-Side Before making deck leveling adjustments, check the tire pressure. Front tires 15 psi, rear tires 10 psi. If tires are properly inflated and mowing is still uneven, adjust side-to-side deck levelness as follows: a.
Section 4 - ADJUSTMENTS & REPAIR 4.2.5. MOWER DECK TIMING ROD ADJUSTMENT The mower deck timing rod is pre-adjusted at the factory. It is set to maintain the deck in the same attitude through all heights of cut. If suspecting the timing rod requires adjustment, contact an authorized SNAPPER dealer for service.
Section 4 - ADJUSTMENTS & REPAIR CAUTION Before attempting any adjustments or repairs, stop the engine, remove the key, remove the spark plug wire from the spark plug, and secure spark plug wire away from spark plug. 1. Follow procedures for standing Rear Engine Rider on rear bumper.
Section 4 - ADJUSTMENTS & REPAIR HOUSING CABLE COTTER-, 3. Measure the distance between end of clutch/brake cable and bottom of housing. Measurement should be no less than 112" and no greater than 3/4". See inset, Figure 4.18. CHAIN- CASE HOUSING COTTER- PIN FIGURE 4.
Section 4 - ADJUSTMENTS & REPAIR 3. Inspect condition of blade. Refer to Figure 4.20. 4. If blade is in good condition, sharpen at 22 to 28 degrees.
Section 4 -ADJUSTMENTS & REPAIR 4.6.2. BELT REPLACEMENT (Continued) 9. Adjust bait guide. See Figure 4.25 for proper bait-to-belt guide clearances. 10. Check mower drive belt tension and adjust if necessary. Refer to 4.2.1., MOWER DRIVE BELT ADJUSTMENT on Page 13.
Section 4 - ADJUSTMENTS & REPAIR CAUTION The electrolyte (acid) produces a highly explosive gas. Keep all sparks, flame and fire away from area when charging battery or when handling electrolyte or battery. Electrolyte (acid) is a highly corrosive liquid.
Section 4 - ADJUSTMENTS & REPAIR 4.6.5. BATTERY TESTING Methods of Checking Battery Condition State of Charcje 100% Charged w/Sulfate Stop 100% Charged 75% Charged 50% Charged 25% Charged 0% Charcjed Syringe Hydrometer 1.280 1.265 1.210 1.160 1.120 Less than 1.
MAINTENANCE SCHEDULE SUBJECT Engine Engine Engine Air Pre-Cleaner Air Cleaner Spark Plug Fuel Filter Engine Cooling System Battery Battery Tires Drive Belts Mower Blades Mower Deck Lubrication Points .
SNAPPER. 5 - 2 YEAR LIMITED WARRANTY COMPONENT PARTS - 5 YEARS For five (5) years from purchase date for original purchaser's residential non-commercial _' use, Snapper, through any Snapper dealer will replace free of charge any part or parts found upon examination by the factory to be defective in material or workmanship or both.
SERVICE NOTES i.
SERVICE NOTES.
Safety Instructions & Operator's Manual for • REAR ENGINE RIDING MOWER SERIES 16 The engine exhaust from this product contains chemicals known to the State of I AWARNING: California to cause cancer, birth defects or other reproductive harm.
Safety Instructions & Operator's Manual for REAR ENGINE RIDING MOWER SERIES 16 MODELS 250816B N250816B 250816BE N250816BE 281016BE N281016BE 301016BE 301216BE 331416BVE 331416KVE PRECIX BODYI.
IMPORTANT SAFETY INSTRUCTIONS WARNING: This powerful cutting machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply with the following SAFETY instructions could result in sedous injury or death to the operator or other persons.
Section 1 - FAMILIARIZATION FUEL VENT TANK REAR BUMPER FUEL FILLER STEERING WHEEL F OPERATOR'S SEAT TRANSMISSION SHIFT; PANEL (See Inset) DECK LIFT LEVER CLUTCH/BRAKE PEDAL CHUTE DEFLECTOR CONTROL PANEL IGNITION SWITCH ENGINE SPEED CQ_TROL BRAKE LEVER 1 I I MOWER DECK I I LEVER FIGURE 1.
Section 2 -OPERATING INSTRUCTIONS 2.1 PRE-START CHECK UST 2.2 Make the following checks and perform the service required before each start-up. 2.1.1. Check tires and add or release air as needed to bring pressure to 15 psi in front and 10 psi in rear tires.
Section 2 - OPERATING INSTRUCTIONS 2.3 STARTING & OPERATION 2.3.1 ENGINE (ELECTRIC START) IMPORTANT: When the ignition key is turned to "START", the engine will turn over, but will not start unless the Clutch/Brake pedal is pressed all the way down, the Blade Lever is in the "OFF" position (See Figure 2.
Section 2- OPERATING INSTRUCTIONS 2.3.1 ENGINE (ELECTRIC START) (Continued) 8. Should the battery be too weak to start the engine, use the instructions shown below, 2.3.2., ENGINE (MANUAL START) to manually start the electric start en- gines. 9. On Model 331416BVE, the engine is equipped with a fuel shut-off solenoid.
Section 2 - OPERATING INSTRUCTIONS /_ CAUTION /'_ Before leaving the Rear Engine Rider with the engine running, STOP the blade, shift to neutral and engage the park brake. 2.4 STOPPING 2.4.1. ENGINE 1. Stop engine by turning key to the "OFF" position.
Section 2 - OPERATING INSTRUCTIONS 2.4.4. PARK BRAKE (Continued) 2. Release park brake by pushing down on the Clutch/Brake Pedal to release park brake lever. See Figure 2.15. PUSH CLUTCWBRAKE PEDAL ALL THE WAY DOWN 2.4.6. WHEEL DRIVE 1. With engine running, adjust engine speed con- trol to "FAST" position.
Section 3 - MAINTENANCE 3.1 INTRODUCTION To retain the quality of the Rear Engine Rider, use genuine SNAPPER replacement parts only. Contact a local SNAPPER dealer for parts and service assistance. For the correct part or information for a particular Rear Engine Riding Mower, always mention the model and sedal number.
Section 3 - MAINTENANCE 3.2.3. CHECK MOWER DRIVE BELT 1. Drive Belt Cover Removal a. Lower deck to lowest setting. b. Remove four self-tapping screws, two on each side of mower drive belt cover. See Figure 3.3. c. Slide cover back and rotate out on left side of mower deck.
Section 3 - MAINTENANCE 3.3.2. MOWER COMPONENTS (Continued) d. Close vent on fuel filler cap. e. Carefully stand Rear Engine Rider on rear bumper. f. Clean underside of mower deck, removing all accumulation of grass clippings and debds. g. Lower Rear Engine Rider to ground and clean top of deck, removing all grass clippings and debris.
Section 3 - MAINTENANCE DIFFERENTIAL . I FIGURE 3.9 Chain Case a. Check fill/level plug for damage. If signs of wear or cracks are visible, replace plug with new plug. See Figure 3.10. b. To check lubricant in chain case, remove fill/level plug and look for lubricant on the internal components of the chain case.
Section 3 - MAINTENANCE 3.5 3.6 EVERY TWO YEARS 3.5.3. Transmission shift lever and detent. 3.5.4. Clutch disc. 3.5.5. Clutch Yoke (See Figure 4.18 on Page 18). 3.5.6. Mower deck linkage and pivot areas. STORAGE (OUT OF SEASON) If desired, the Rear Engine Rider can be stored on the rear bumper.
Section 4 - ADJUSTMENTS & REPAIR Before performing any service or maintenance I procedures, always remove key from ignition I switch, remove spark plug wire from spark plug and I secure spark plug wire away from spark plug.
Section 4 - ADJUSTMENTS & REPAIR CAUTION Before performing any service or maintenance procedures, always remove key from ignition switch, remove spark plug wire from spark plug and secure spark plug wire away from spark plug. 4.2.2. BLADE BRAKE ADJUSTMENT 1.
Section 4 - ADJUSTMENTS & REPAIR LOOSEN SHOULDER BOLT 4.2.4. MOWER DECK ADJUSTMENT (LEVELNESS) 1. Side-To-Side Before making deck leveling adjustments, check the tire pressure. Front tires 15 psi, rear tires 10 psi. If tires are properly inflated and mowing is still uneven, adjust side-to-side deck levelness as follows: a.
Section 4 - ADJUSTMENTS & REPAIR 4.2.5. MOWER DECK TIMING ROD ADJUSTMENT The mower deck timing rod is pre-adjusted at the factory. It is set to maintain the deck in the same attitude through all heights of cut. If suspecting the timing rod requires adjustment, contact an authorized SNAPPER dealer for service.
Section 4 - ADJUSTMENTS & REPAIR CAUTION Before attempting any adjustments or repairs, stop the engine, remove the key, remove the spark plug wire from the spark plug, and secure spark plug wire away from spark plug. 1. Follow procedures for standing Rear Engine Rider on rear bumper.
Section 4 - ADJUSTMENTS & REPAIR HOUSING CABLE COTTER-, 3. Measure the distance between end of clutch/brake cable and bottom of housing. Measurement should be no less than 112" and no greater than 3/4". See inset, Figure 4.18. CHAIN- CASE HOUSING COTTER- PIN FIGURE 4.
Section 4 - ADJUSTMENTS & REPAIR 3. Inspect condition of blade. Refer to Figure 4.20. 4. If blade is in good condition, sharpen at 22 to 28 degrees.
Section 4 -ADJUSTMENTS & REPAIR 4.6.2. BELT REPLACEMENT (Continued) 9. Adjust bait guide. See Figure 4.25 for proper bait-to-belt guide clearances. 10. Check mower drive belt tension and adjust if necessary. Refer to 4.2.1., MOWER DRIVE BELT ADJUSTMENT on Page 13.
Section 4 - ADJUSTMENTS & REPAIR CAUTION The electrolyte (acid) produces a highly explosive gas. Keep all sparks, flame and fire away from area when charging battery or when handling electrolyte or battery. Electrolyte (acid) is a highly corrosive liquid.
Section 4 - ADJUSTMENTS & REPAIR 4.6.5. BATTERY TESTING Methods of Checking Battery Condition State of Charcje 100% Charged w/Sulfate Stop 100% Charged 75% Charged 50% Charged 25% Charged 0% Charcjed Syringe Hydrometer 1.280 1.265 1.210 1.160 1.120 Less than 1.
MAINTENANCE SCHEDULE SUBJECT Engine Engine Engine Air Pre-Cleaner Air Cleaner Spark Plug Fuel Filter Engine Cooling System Battery Battery Tires Drive Belts Mower Blades Mower Deck Lubrication Points .
SNAPPER. 5 - 2 YEAR LIMITED WARRANTY COMPONENT PARTS - 5 YEARS For five (5) years from purchase date for original purchaser's residential non-commercial _' use, Snapper, through any Snapper dealer will replace free of charge any part or parts found upon examination by the factory to be defective in material or workmanship or both.
SERVICE NOTES i.
SERVICE NOTES.
Safety Instructions & Operator's Manual for • REAR ENGINE RIDING MOWER SERIES 16 The engine exhaust from this product contains chemicals known to the State of I AWARNING: California to cause cancer, birth defects or other reproductive harm.
デバイスSnapper SERIES 16 250816Bの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Snapper SERIES 16 250816Bをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSnapper SERIES 16 250816Bの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Snapper SERIES 16 250816Bの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Snapper SERIES 16 250816Bで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Snapper SERIES 16 250816Bを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSnapper SERIES 16 250816Bの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Snapper SERIES 16 250816Bに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSnapper SERIES 16 250816Bデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
