SnapperメーカーSPE1250KW, SPE140KW, SPE150KH, SPE360, SPE480の使用説明書/サービス説明書
ページ先へ移動 of 32
Safety Instructions and Operator’s M anual for PRO GEAR EXPRESS WALK BEHIND MOWERS MID-SIZE SERIES 0 POWER UNIT MODEL SPE1250KW SPE140KW SPE150KH MOWER UNIT MODEL SPE360 SPE480 MODEL NUMBER EXPLA NA.
2 IMPORTA N T SA FETY INSTRUCTIONS WARNING: This powerf ul cuttin g machine is capable of amp utating hand s and feet and can t hrow ob jects that can cause in jury and damage! Failure to comply wi th the follo wing SAFETY inst ructions coul d result in serious injury or death to the ope rator or other persons.
3 IMPORTA NT SA FETY INSTRUCTIONS OPERA TION 1. DO NOT put hands or feet near or unde r rotating parts. Keep clear of th e disch arge area w hile the engine is running. 2. Stop Blades when cro ssing gravel driv e, walks, and under any conditions where thrown objects might be a hazard.
4 TA BLE OF CONTENTS IMPO RTA NT SAFETY INST RUCTIONS ...................................................................................2-3 TABLE OF CONTENT S ...........................................................................................
5 SECTION 1 - FA MILIA RIZA TION FIGURE 1.1 1.1 INTRODUCT ION This manual has been prepar ed for the operator’s of the SNAPPER PRO GEAR W ALK BEHIND MOW ER. Its purpose, aside f rom recom mending standar d operating procedures and routine service r equirements , is to prom ote SAFETY thr ough the use of ac cepted operating practic es.
6 SECTION 2 - SA FETY MESSA GES A ND DECA LS REVERSE NEUTRA L TRA NSMISSION SH IFT LEVER POSIT IONS LOWEST SPEED HIGHEST SPEED CHOKE SYMBOL RA BBI T “FA ST” SPEED TURTLE “SLOW” SPEED KEYSW ITC.
7 SECTION 2 - CONTROLS FIGURE 2.1 BLA DE CLUTCH SW ITCH KEY SW ITCH OPERA TOR ’S PRESENCE CONTROL (OPC) RIGHT HA ND TRA CT ION LEVER TRACTION LOCK LEVER TRA NSMISSION SHIFT LEVER ENGINE SPEED CONTRO.
8 SECTION 3 - OPERA TING INSTRUCTIONS 3.1 BEFORE OPERA TING Be Thoroughly fam iliar with all controls and how to use them bef ore operating the m achine. Know beforehand how to STOP the T raction W heel Drives, Mower Blades and Engine in preparation f or possible em ergencies.
9 SECTION 3 - OPERA TING INSTRUCTIONS 3.4 PRE-STA RT CHECK LIST Make the f ollowing checks and perform the services as required bef ore each start-up: 1. If required, m ake c utting height adjustments . Refer to Section “CUTTING HEIGHT ADJUSTMENT”.
10 SECTION 3 - OPERA TING INSTRUCTIONS 3.5 STA RTING & OPERA TING - PISTO L GRIP (Continued from previous page) 5. Move Engine Speed Control Lever to the CHOKE position. See Figure 3.6. 6. Tur n Key Switch to RUN position. FIGURE 3.6 IMPO RTA NT : DO NOT jer k the engine recoil starter handle or allow it to snap back .
11 SECTION 3 - OPERA TING INSTRUCTIONS 3.5 STA RTING & OPERA TING (Continued from previous page ) 13. PISTOL GRIP - TO ST OP MA CHINE , Simu ltaneously s queeze both Traction Levers firm ly against the handle while pulling the Trac tion Lock Levers rearward with index f inger until latched.
12 SECTION 3 - OPERA TING INSTRUCTIONS WA RNING Brakes require main tenance. Inspect f or proper operation before oper ating machine. Refer to Section “A DJUST MENTS, STEERING AND BRA KES”. 3.7 TRA CTION LOCK OPERATION - PISTOL GRIP 1. Simultaneously squeez e both Tr action Levers toward the handle, to stop mower movement .
13 SECTION 3 - OPERA TING INSTRUCTIONS 3.10 CUTTING HEIGHT A D JUSTMENT (Fixed Decks) Mower has three m ethods of adjus ting cutting height: 1. Moving position of BLADE on cutter spindle s haft. 2. Moving position of CASTER W HEEL on support. 3. Moving position of MOW ER DECK on power unit.
14 SECTION 3 - OPERA TING INSTRUCTIONS 3.12.1 ADJUSTING BLADE ON CUTT ER SPINDLE (Continued) FIGURE 3.15 3 . 1 3 A DJUSTING FIXED DECK A TTA CHMENT The m ower deck has f our diff er ent positions for attaching it to the power unit.
15 SECTION 4 - TROUBLESHOOTING ENGINE TR OUBLESHOOTING S YMP TOM P ROB LEM S OL UTI ON Engine ................... Key OFF. ...............................................................................................Turn Key to Run. does not .......
16 SECTION 4 - TROUBLESHOOTING MOWER TROUBLESHOOTI NG (Continued) S YMP TOM P ROB LEM S OL UTI ON Mower not ...................................... Broken or slipping Blade Belt. ...................................... Replace Belt. cutting full .......
17 SECTION 5 - A DJUSTMENTS 5.1 STEERING/BRA KES If machine is not as responsive as desired when either Trac tion lever is squeezed, one or both brak es should be adjusted as f ollows: 1. Oper ate mower on level terrain with Tr ansmis sion Shift Lever in No.
18 SECTION 5 - A DJUSTMENTS 5.3 HA NDLE HEIGHT The operator handle can be adjusted for operator com fort as f ollows: 1. Loosen the upper car riage bolt and nut on both s ides of handlebar. 2. Remove lower c arriage bolt and nut on both s ides of handlebar.
19 SECTION 6 - POWER UNIT SERVICE 6.1 REPLA CEMENT PA RTS To retain the quality of your mower, use G enuine SNAPPER Replacem ent Parts only! Contact your local SNAPPER dealer for parts and service ass istance. For the correc t part or inform ation for y our mower, alway s mention Model and Ser ial Number of Power Unit and Mower Attachm ent.
20 SECTION 7 - MOWER A TTA CHMENT SERVICE 7.1 TRA NSMISSION BELT REMOVA L/REPLA CEMENT Should it becom e nec es sar y to replace the transm ission drive belt, contact an authorized SNAPPER Dealer f or servi ce. WA RNING DO NOT attempt any maintenance, adjustmen ts or service with the engine r unning.
21 SECTION 7 - MOWER A TTA CHMENT SERVICE 7.4 CUTTING BLA DE SERVICE Check blades after each us e for signs of excess ive wear and damage. See F igure 7.4 for blade wear lim its. FIGURE 7.4 1. Use the f ollowing chart for order ing replacem ent Blades for the 36” & 48” Mowing Decks.
22 SECTION 7 - MOWER A TTA CHMENT SERVICE 7.5 MO WER SPINDLES (Field Serviceable Spindles) BEA RING REPLACEMENT In the event that a spindle bearing requires replacem ent, the SNAPPER Field Serviceable Spindles have been designed s o that no special tools or pres ses are required.
23 ELECTRICA L FIGURE 7.9 KEY W ITH COVER KEYSW ITCH BLA DE CLUTCH SW ITCH OPC SW ITCH (PISTOL G RIP MODELS ONLY ) CONNECTOR NOTCH 15 A M P FUSE TO TRA NSMISSION SW ITCH MA IN WIR E HA RNE SS OPC SW I.
24 ELECTRICA L FIGURE 7.10 FIGURE 7.11 BLA CK BLUE ELECTRIC CL UTCH YELLOW BLADE SWITCH ENGINE GREEN 15A FUSE GREEN IGNIT ION RED RED BLA CK OPC R.H. WH IT E OPC L.
25 2 YEA R LIMITED WA RRA NTY For two (2) y ears from purchase date f or the original purchaser 's use, SNA PPER , through any authorized SNA PPER dealer will replace, fr ee of charge (ex cept fo.
26 PRIMA RY MA INTENA NCE.
27 PRIMA RY MA INTENA NCE.
28 PRIMA RY MA INTENA NCE.
29 PRIMA RY MA INTENA NCE.
30 NOTES.
31 NOTES.
32 Safety Instructions and Operator’s M anual for PRO GEAR EXPRESS MID-SIZE WALK BEHIND MOWERS SERIES 0 IMPORTANT Snapper products are built using engines that meet or exceed all a pplicable emissions requirements on the date manufactured. The labels on thos e engines contai n very importa nt emissions informa tion and critical safety warnings.
デバイスSnapper SPE1250KW, SPE140KW, SPE150KH, SPE360, SPE480の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Snapper SPE1250KW, SPE140KW, SPE150KH, SPE360, SPE480をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSnapper SPE1250KW, SPE140KW, SPE150KH, SPE360, SPE480の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Snapper SPE1250KW, SPE140KW, SPE150KH, SPE360, SPE480の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Snapper SPE1250KW, SPE140KW, SPE150KH, SPE360, SPE480で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Snapper SPE1250KW, SPE140KW, SPE150KH, SPE360, SPE480を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSnapper SPE1250KW, SPE140KW, SPE150KH, SPE360, SPE480の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Snapper SPE1250KW, SPE140KW, SPE150KH, SPE360, SPE480に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSnapper SPE1250KW, SPE140KW, SPE150KH, SPE360, SPE480デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
