SnapperメーカーSZT18336BVEの使用説明書/サービス説明書
ページ先へ移動 of 36
Safety Instructions & Operator’s Manual for SCRAMBLER ZERO-TURN HYDRO DRIVE SERIES 6 MODELS SZT18336BVE SZT18386BVE MODEL NUMBER EXPLANATION S Z T 18 33 6 B V E MODEL DESIGNATION ENGINE OPTIONS DRIVE SYSTEM TYPE ENGINE TYPE ENGINE HORSE POWER * SERIES DESIGNATION CUTTING WIDTH S – Scrambler ZT – Zero Turn 18 – 18.
2 IMPORTANT SAFETY INSTRUCTIONS WARNING: This pow erful cutting machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply w ith the follow ing SAFETY instructions could result in serious injury or death to the operator or other persons.
3 IMPORTANT SAFETY INSTRUCTIONS PREPARATION (Continued From Previous Page) 6. Check the area to be mow ed and remove all objects such as toys, w ire, rocks, limbs and other objects that could cause injury if thrown by blade or interfere w ith mowing. 7.
4 IMPORTANT SAFETY INSTRUCTIONS TOWING 1. Tow only w ith a machine that has a hitch designed for tow ing. DO NOT attach towed equipment except at the hitch point. 2. Follow the manufacturer’s recommendation for w eight limits for tow ed equipment and towing on slopes.
5 TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIO NS ........................................................................ 2-4 TABLE OF CO NTENTS ...................................................................................................... 5 SECTION 1 - FAMI LIARIZATI ON.
6 Section 1 - FAMILIARIZATION FIGURE 1.1 1. 1 INTRODUCTION This manual has been prepared for operators of the SNAPPER SCRAMBLER ZERO-TURN MOWER. Its purpose, aside from recommending standard operating procedures and routine service requirements, is to promote SAFETY through the use of accepted operating practices.
7 Section 1 - FAMILIARIZATION 1.3 BASIC CONTROLS AND THEIR FUNCTIONS The figures below identify each of the operator controls and their basic function. Controls will be described in greater detail further on in this manual. 1.3.1. IGNITION SWITCH (Left Control Panel) Starts and stops engine.
8 Section 2 - OPERATING INSTRUCTIONS WARNING DO NOT attempt to operate the machine until you have read this manual thoroughly and become familiar w ith all controls and operating procedures. Serious injury or damage can result. 2.1 PRE-START CHECK LIST Make the following checks and perform the service required before each start-up.
9 Section 2 - OPERATING INSTRUCTIONS 2.3 MOTION CONTROL IMPORTANT: This machine is equipped with hydrostatic drive. The direction and speed of movement are controlled by dual motion control levers. A small amount of movement of either lever ma y c a u s e t h e m a c h i n e t o move instantly, and can result in severe injury or damage.
10 Section 2 - OPERATING INSTRUCTIONS 2.3.4. CONVENTIONAL TURNING 1. To turn left , slowly ease back on the left lever while keeping or increasing pressure on the right lever. See Figure 2.6. The more you ease off on the left lever and/or push on the right lever, the tighter the turn.
11 Section 2 - OPERATING INSTRUCTIONS 2.4 MOWER OPERATION 2.4.1. CUTTING HEIGHT ADJUSTMENT This machine has seven different cutting height positions. IMPORTANT: When positioning the cutting deck into a higher cutting position, pull up on the deck lift handle only, it is not necessary to pull up on the release lever at the same time.
12 Section 2 - OPERATING INSTRUCTIONS 2.5 SAFETY INTERLOCK SYSTEM CHECKS This machine is equipped with an electrical safety interlock system that is pr ovided for the safety of the operator and others. All safety devices must be in place and functioning properly befor e operating the machine.
13 Section 3 - MAINTENANCE 3.1 INTRODUCTION To retain the quality of the SCRAMBLER, use genuine SNAPPER replacement parts only. Contact a local SNAPPER dealer for parts and service assistance. For the correct part or information for a particular mower, always mention the model and serial number.
14 Section 3 - MAINTENANCE WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remove spark plug wire from spark plug and secure aw ay from plug. Engine and components are HOT.
15 Section 3 - MAINTENANCE WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remove spark plug wire from spark plug and secure aw ay from plug. Engine and components are HOT.
16 Section 3 - MAINTENANCE WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remove spark plug wire from spark plug and secure aw ay from plug. Engine and components are HOT.
17 Section 3 - MAINTENANCE WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remove spark plug wire from spark plug and secure aw ay from plug. Engine and components are HOT.
18 Section 4 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remove spark plug wire from spark plug and secure aw ay from plug.
19 Section 4 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remove spark plug wire from spark plug and secure aw ay from plug.
20 Section 4 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remov e spark plug w ire from spark plug and secure aw ay from plug.
21 Section 4 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remove spark plug wire from spark plug and secure aw ay from plug.
22 Section 4 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remove spark plug wire from spark plug and secure aw ay from plug.
23 Section 4 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remov e spark plug w ire from spark plug and secure aw ay from plug.
24 Section 4 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remove spark plug wire from spark plug and secure aw ay from plug.
25 Section 4 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remov e spark plug w ire from spark plug and secure aw ay from plug.
24 Section 4 - ADJUSTMENTS & REPAIR 4.6.5. BATTERY TESTING There are two types of battery tests: Unloaded and Loaded. The unloaded test is the procedure that will be discussed. It’s the simplest and most commonly used. An unloaded test is made on a battery without discharging current.
25 TROUBLESHOOTING PROBLEM PROBABLE CAUSE CORRECTIVE ACTION Starter Will Not Crank 1. Battery dead. 1. Service battery. Engine 2. Blown fuse. 2. Replace fuse. 3. Electrical connections loose or corroded. 3. C l ean and check connections for good contact.
26 TROUBLESHOOTING PROBLEM PROBABLE CAUSE CORRECTIVE ACTION Excessive Vibration 1. Damaged, out of balance or bent mo wer blades. 1. Service mower blade(s). 2. Loose blade components. 2. Service and tighten loose parts. 3. Loose or missing air lift (if equipped).
27 SERVICE SCHEDULE ITEM SERVICE PERFORMED REF. EACH USE 5 HRS 25 HRS 50 HRS 100 HRS EACH SEASON Engine Oil Check Oil Level Page 8 X Initial Oil Change Page 13 X Periodic Oil Change Page 14 X* Oil Fil.
28 2 YEAR LIMITED WARRANTY For two (2) years from purchase date for the orig inal purchaser's residential, non-commercial use, SNAPPER , through any authorized SNAPPER dealer will replace, free o.
29 PRIMARY MAINTENANCE 31.
30 PRIMARY MAINTENANCE 32.
31 PRIMARY MAINTENANCE 33.
32 PRIMARY MAINTENANCE 34.
33 SNAPPER PRODUCT REGISTRATION FORM IMPORTANT: KEEP THIS INFORMATION FOR YOUR PERSONAL RECORDS (Complete the following informa tion on your Snapper purchase) Model Number ____________________________.
34 Safety Instructions & Operator’s Manual for SCRAMBLER ZERO-TURN HYDRO DRIVE SERIES 6 IMPORTANT Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufactured. The labels on those engines contai n very important emissions information and critical safety warnings.
デバイスSnapper SZT18336BVEの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Snapper SZT18336BVEをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSnapper SZT18336BVEの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Snapper SZT18336BVEの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Snapper SZT18336BVEで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Snapper SZT18336BVEを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSnapper SZT18336BVEの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Snapper SZT18336BVEに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSnapper SZT18336BVEデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
