SohoメーカーFSD-800の使用説明書/サービス説明書
ページ先へ移動 of 22
FSD-8080 User's Manual i SOHOConnect Series FSD-800 8-port 10/100Mbps Ethernet Switch.
SOHOConnect Series Trademarks Copyright PLANET T echnology Corp. 2000. PLANET is a registered trademark of PLANET T echnology Corp. All other trademarks belong to their respective owners.
FSD-800 User's Manual 1 Table of Contents CHAPTER 1 ............................................................................ 1 G ENERAL I NTRODUCTION ...................................................... 1 Checklist .........................
SOHOConnect Series 2 This page is intentionally left blank ..
FSD-800 User's Manual 1 Chapter 1 General Introduction Checklist Check the contents of your package for following parts: ♦ The Fast Ethernet Switch ♦ Power Cord ♦ User ’ s Manual If any o.
SOHOConnect Series 2 a network more efficiently than bridges or routers in most environments. In the following sections, the term “ Switch ” will represent Planet ’ s FSD-800, and “ switch ” for third part Ethernet switches.
FSD-800 User's Manual 3 connecting workgroup devices and desktops, companies no longer have to invest in expensive and inflexible switches engineered primarily for backbone implementations.
SOHOConnect Series 4 ♦ LED indicators for simple diagnostics and management ♦ Port#8 provides an extra port for MDI and MDI-X mode PC or hub Uplink.
Chapter 2 Hardware Description This section describes the hardware features of the Switch. For easier management and control of the Switch, familiarize yourself with its display indicators, and ports. Front panel illustrations in this chapter display the unit LED indicators.
SOHOConnect Series 6 LED indicators LED Function Color Description Power (PWR) Green This indicator lights green when the hub is receiving power , otherwise, it is off.
FSD-800 User's Manual 7 100V~240VAC 50~60Hz Figure 2. Rear Panel of FSD-800 Hardware Installation 1. Place the Switch on a smooth surface 2. Connect the output cord of power supply to the AC-jack. 3. Connect hub or PC to one port of the Switch using Category 3/4/5 UTP/STP cabling.
SOHOConnect Series 8 may initially seem to work, it will soon cause data loss. All kinds of hub/PC can connect to switch by using straight- through wires. The hub provides one additional RJ45 connector that is converted from port 1, labeled “ Uplink ” port.
FSD-800 User's Manual 9 Uplink Figure 3. 100Mbps File server to Hubs Connection 10Mbps Hub to 100Mbps Hub Plug one end of the Category 5 UTP Cable into one port of the Switch, and the other end of this cable into “ Uplink ” port of the 100Mbps Fast Ethernet Hub.
SOHOConnect Series 10 Switch Operation Address Table The Switch is implemented with an address table. This address table composed of many entries. Each entry is used to store the address information of some node in network, including MAC address, port no, etc.
FSD-800 User's Manual 11 located at different port from this packet comes in; the Ethernet Switch will forward this packet to the port where this destination address is located according to the information from address table.
SOHOConnect Series 12 cabling and adapters. Due to the learning function of the Ethernet switch, the source address and corresponding port number of each incoming and outgoing packet are stored in a routing table. This information is subsequently used to filter packets whose destination address is on the same segment as the source address.
FSD-800 User's Manual 13 If attached device is: 100Base-TX port will set to: • 10Mbps, no auto-negotiation 10Mbps • 10Mbps, with auto-negotiation 10/20Mbps (10Base-T/Full-Duplex) • 100Mbps,.
SOHOConnect Series 14 This page is intentionally left blank ..
Chapter 3 Troubleshooting This chapter contains information to help you solve problems. If the Switch is not functioning properl y , make sure the Switch was set up according to instructions in this manual. The Link LED is not Lit Solution: Make sure the switch configuration is consistent with the connecting device Check the cable connections.
SOHOConnect Series 16 The address table may contain older information than of the address table of that node. Please power down to refresh the address information.
Appendix A Specifications: General (Ethernet) Standards: IEEE 802.3 10Base-T Ethernet IEEE 802.3u 100 Base-TX Fast Ethernet ANSI/IEEE Std 802.3 N-way auto-negotiation IEEE 802.
SOHOConnect Series 18 General (Ethernet) Humidity 10% ~ 90% non-condensing Dimensions 251 x 118 x 37 mm EMI FCC Class A, CE Mark Class A Performance Transmission Method Store-and-forward Filtering Add.
デバイスSoho FSD-800の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Soho FSD-800をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSoho FSD-800の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Soho FSD-800の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Soho FSD-800で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Soho FSD-800を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSoho FSD-800の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Soho FSD-800に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSoho FSD-800デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
