SonyメーカーCCD-TRV33の使用説明書/サービス説明書
ページ先へ移動 of 56
CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E Model No. CCD- Model No. AC- Serial No. Serial No. Video Camera Recor der Operating Instructions Before operating the unit, please read this manual thoroughly, and retain it for future reference. Owner’s record The model and serial numbers are located on the bottom.
2 CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).
3 CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E Before you begin T able of contents Before you begin Using this manual ................................... 4 Checking suppllied accessories ............ 5 Getting started Charging and installing the battery pack .
4 CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E CINEMA Mode r Steady Shot r r Zoom (X) 26X (Digital) 26X (Digital) 52X (Digital) The instructions in this manual are for the five models listed below. Before you start reading this manual and operating the unit, check your model number by looking at the bottom of your camcorder.
5 CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E Before you begin 12 45 7 3 6 Check that the following accessories are supplied with your camcorder. 1 Wireless Remote Commander (1) (p. 17, 51) 2 NP-33 Battery Pack (1) (p. 6) 3 CR2025 Lithium Battery (1) (p.
6 CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E LCD open 2) LCD close NP-C65 105 NP-68 125 NP-78 170 NP-98/98D 215 NP-33(supplied) 60 Battery pack Charging time*(min) Charging Time Getting started Charging and installing the battery pack * Approximate minutes to charge an empty battery pack using the supplied AC power adaptor.
7 Getting started CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E 1 2 NP-78 175 (95) 220 (120) 180 NP-98/98D 220 (110) 300 (160) 220 NP-60D 95 (50) 125 (70) 95 NP-C65 100 (50) 150 (80) 100 NP-80/80.
8 CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E EJECT PUSH To remove the battery pack Slide BATT, and then pull the lower part of the battery pack. Charging and installing the battery pack 1 2 Inserting a cassette Make sure that a power source is installed.
9 CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E Basic operations Make sure that a power source and a cassette is inserted and that the START/STOP MODE switch inside the LCD panel is set to . When you use the camcorder for the first time, power on it and reset the date and time to your time (p.
CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E 10 Note on standby mode If you leave the camcorder for 5 minutes or more with a cassette inserted in Standby mode, the camcorder goes off automatically. This prevents wearing down the battery and wearing out the tape.
11 CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E Basic operations Notes on the tape counter • The tape counter indicates the recording or playback time. Use it as a guide. There will be a time lag of several seconds from the actual time. To set the counter to zero, press COUNTER RESET.
CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E 12 1 2 90˚ 210˚ BRIGHT 90˚ Camera recording Zooming speed (Variable speed zooming) Turn the power zoom lever fully for a high-speed zoom.
13 CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E Basic operations To let the subject monitor the shot Turn the LCD panel over (p.21). Notes on the LCD panel • When closing the LCD panel, turn it vertically until it clicks [a] .
CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E 14 Hints for better shooting • You can record in a low position to get an interesting recording angle.
15 CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E Basic operations Œ 2 1 3 L S T A N D B Y O C K EDITSEARCH Œ Œ CAMERA PLAYER OFF Using EDITSEARCH, you can review the last recorded scene or check the recorded picture in the viewfinder. You can also review the picture on the LCD screen.
CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E 16 VOLUME CAMERA PLAYER OFF You can monitor the playback picture on the LCD screen. (1) While pressing the small green button on the POWER switch, set it to PLAYER. (2) Insert the recorded tape with the window facing out.
17 CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E Basic operations When watching on the LCD screen You can turn the LCD panel over and move back to the camcorder with the LCD screen facing out. [a] You can change the angle of the LCD panel. [b] 30˚ Using the Remote Commander You can control playback using the supplied Remote Commander.
CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E 18 Playing back a tape You can go to the end of the recorded portion after you record and play back the tape to make the transition between the last scene you recorded and the next scene smooth.
19 CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E Advanced operations Accessory to be used Supplied AC power adaptor Battery pack (Ni-Cd type) Battery case (supplied) except CCD-TRV112/TRV212 Sony.
20 CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E CCD-TRV22/TRV33/TRV212 105 (55) 150 (80) 105 Notes on the POWER lamp • The POWER lamp will remain lit for a while even if the unit is unplugged after use. This is normal. • If the POWER lamp does not light, set the selector to VTR (DC OUT) and disconnect the power cord.
21 CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E Advanced operations Notes • The above battery lives are estimates. The battery life may be shorter depending on the storage condition of the battery before being purchased and temperature. • You may not use the battery case in cold environment.
22 CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E Before you start recording or during recording, press DATE(+) or TIME(NEXT). You can record the date or time displayed on the LCD screen or in the viewfinder with the picture. You cannot record the date and time at the same time.
23 CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E Advanced operations Shooting with backlighting When you shoot a subject with the light source behind the subject or a subject with a light background, use the BACK LIGHT function. Press BACK LIGHT.
24 CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E Using the PROGRAM AE function You can select from three PROGRAM AE (Auto Exposure) modes to suit your shooting situation. When you use PROGRAM AE, you can capture high-speed action or night views. Selecting the best mode Select the best mode by using the following examples.
25 CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E Advanced operations Selecting the ST ART/STOP mode Your camcorder has two modes besides normal start/stop mode. These modes enable you to take a series of quick shots resulting in a lively video, or to avoid recording unnecessary scenes resulting from failing to turn off the camcorder.
26 CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E You can select from nine preset titles to superimpose it on the picture during recording. Each time you press TITLE, the preset titles appear one by one. To superimpose from the beginning (1) Set the POWER switch to CAMERA.
27 CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E Advanced operations [b] [a] [c] – CCD-TRV22/TRV33/TRV212 only You can use the Steady Shot to compensate for camera-shake. Do not use the Steady Shot when shooting a stationary object with a tripod.
28 CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E Changing the mode settings You can change the mode settings to further enjoy the features and functions. (1) While pressing PUSH OPEN, open the LCD panel. You will find the mode switches. (2) Set the mode switches to the desired mode.
29 CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E Advanced operations W atching on a TV screen Connect the camcorder to your VCR or TV to watch the playback picture on the TV screen. When monitoring the playback picture by connecting the camcorder to your TV, we recommend you to use the house current for the power source.
30 CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E Editing onto another tape You can create your own video program by editing with any other h 8 mm, H Hi8, j VHS, k S-VHS, VHSC, K S-VHSC, l Betamax or ¬ ED Betamax VCR that has video/audio inputs.
31 CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E Additional information Your camcorder is supplied with a lithium battery installed. When the battery becomes weak or dead, the I indicator flashes in the viewfinder or on the LCD screen for about 5 seconds when you set the POWER switch to CAMERA.
CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E 32 Changing the lithium battery When replacing the lithium battery, keep the battery pack or other power source attached. Otherwise, you will need to reset the date and time. (1) Open the lid of the lithium battery compartment.
33 CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E Additional information S T A N D B Y CAMERA PLAYER OFF Reset the date and time using the DATE(+) and TIME(NEXT) buttons. (1) Set the POWER switch to CAMERA. (2) Turn STANDBY up. (3) While pressing PUSH OPEN, open the LCD panel.
CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E 34 Playback modes The playback mode (SP/LP) is selected automatically according to the recording system in which the tape has been recorded. The quality of the recorded picture in LP mode, however, will not be as good as that in SP mode.
35 CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E Additional information When the remaining battery indicator reaches the lowest point, the i indicator appears and starts flashing in the viewfinder or on the LCD screen.
CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E 36 Notes on charging A brand-new battery A brand-new battery pack is not charged. Before using the battery pack, charge it completely. After long storage Recharge the battery pack after a long period of storage.
37 CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E Additional information Notes on the Battery Case – CCD-TRV12/TRV22/TRV33 only • Use only with alkaline batteries. You cannot use the battery case with manganese batteries or size AA rechargeable NiCd batteries.
CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E 38 Moisture condensation If the camcorder is brought directly from a cold place to a warm place, moisture may condense inside the camcorder, on the surface of the tape, or on the lens. In this condition, the tape may stick to the head drum and be damaged or the camcorder may not operate correctly.
39 CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E Additional information Removing dust from inside the viewfinder (1) Remove the screw with a screwdriver (not supplied). Then, while sliding the RELEASE knob, turn the eyecup in the direction of the arrow and pull it out.
CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E 40 Precautions Camcorder operation • Operate the camcorder using 6.0 V (battery pack), or 7.5 V (AC power adaptor).
41 CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E Additional information AC power adaptor Charging • Attach the battery pack firmly. • Place the battery pack on a flat surface without vibration during charging. Others • Unplug the unit from the wall outlet when not in use for a long time.
CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E 42 Using your camcorder abr oad Each country or area has its own electricity and TV color systems. Before using your camcorder abroad, check the following points: Power sources You can use your camcorder in any country or area with the supplied AC power adaptor within 110 V to 240 V AC, 50/60 Hz.
Additional information CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E 43 If you run into any problem using the camcorder, use the following table to troubleshoot the problem. Should the difficulty persist, disconnect the power source and contact your Sony dealer or local authorized Sony service facility.
44 CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E Symptom The date or time indicator disappears. Recording stops in a few seconds. Picture Symptom The image on the viewfinder screen is not clear. A vertical band appears when a subject such as lights or a candle flame is shot against a dark background.
Additional information CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E 45 AC power adaptor Symptom The POWER lamp does not light. The CHARGE lamp flashes. Cause and/or Corrective Actions • Set the selector to VTR (DC OUT) and disconnect the power cord.
46 CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E Video camera recorder System Video recording system Two rotary heads, Helical scanning, FM system Audio recording system Rotary heads, FM system V.
47 Additional information CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E STOP REW PLAY FF PAUSE 1 Tape transport buttons (p. 16, 17) p STOP 0 REW (rewind) ( PLAY (playback) ) FF (fast forward) P PAUSE These buttons will function in PLAYER mode. 2 EDITSEARCH button (p.
48 CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E !∞ Recording lamp !§ DATE (+) button (p. 22) !¶ TIME (NEXT) button (p. 22) !• LCD screen (p. 16, 54) !ª Lithium battery compartment (p. 32) @º DISPLAY button (p. 17) @¡ COUNTER RESET button (p.
49 Additional information CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E #¡ START/STOP button (p. 14) Use this button when recording in a low position. #™ Tripod receptacle (p. 14) #£ PUSH OPEN button (p. 12, 16) #¢ LCD BRIGHT dial (p. 12) #∞ Eyecup (p.
50 CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E $º Cassette compartment (p. 8) $¡ EJECT knob (p. 8) $™ Eyecup release knob (p. 39) $£ Hooks for shoulder strap $¢ Grip strap (p. 13) $∞ VIDEO OUT jack (p. 29) $§ RFU DC OUT (RFU adaptor DC out) jack $¶ AUDIO OUT jack (p.
51 Additional information CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E Remote commander Using the Remote Commander Make sure that the COMMANDER mode is set to ON (p. 28). The buttons that have the same name on the Remote Commander as on the camcorder function identically.
52 CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E To prepare the remote commander To use the Remote Commander, you must insert two size AA (R6) batteries. Use the supplied size AA (R6) batteries. (1) Remove the battery cover from the Remote Commander.
53 Additional information CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E Remote control direction Aim the Remote Commander to the remote sensor within the range as shown below. Notes on the Remote Commander • Keep the remote sensor away from strong light sources such as direct sunlight or illumination.
54 CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E In the viewfinder and on the LCD screen 1 Power zoom indicator (p. 12) 2 Back light indicator (p. 23) 3 Warning indicator (p. 55) 4 Lithium battery indicator (p. 31) 5 Recording lamp/battery lamp (p.
55 Additional information CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E W ar ning indicators If indicators flash in the viewfinder or on the LCD screen, or a caution lamp on the camcorder flashes, check the following: ≥ : You can hear the beep sound when BEEP is set to ON (p.
CCD-TRV12/TRV22/TRV33/TRV112/TRV212 3-859-057-15.E S Shoulder strap .................... 50 Sports mode ........................ 24 STANDBY ....................... 9, 10 Standby mode .................... 10 STEADY SHOT .................. 27 Supplied accessories .
デバイスSony CCD-TRV33の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Sony CCD-TRV33をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSony CCD-TRV33の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Sony CCD-TRV33の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Sony CCD-TRV33で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Sony CCD-TRV33を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSony CCD-TRV33の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Sony CCD-TRV33に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSony CCD-TRV33デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。