Sony EricssonメーカーTT4031 (SE-GM29)の使用説明書/サービス説明書
ページ先へ移動 of 280
Owner’s Manual Rev 1.0 Page 1 of 1 TT4031 (SE-GM29) Wireless Modem TT4031 (SE-GM29) Wireless Modem Unit Sony Ericsson GM29 Original Equipm ent Manufactured by Sony Ericsson Mobile C omm unications I.
Owner’s Manual Rev 1.0 Page 2 of 2 Topp Consumer Products is an authorized distri butor of the TT4031 (SE-GM29) Wireless Modem unit, manufactured by Sony Ericsson Mobile Co mmunications International and distributed by Sony Ericsson Mobile Communications Internat ional as the GM29 Wireless Modem Unit.
Owner’s Manual Rev 1.0 Page 3 of 3 Notices, License, and Warranty CAUTION: TOPP CONSUMER PRODUCTS PROVID ES TO YOU THIS TT4031 (SE-GM29) WIRELESS MODEM PRODUCT ALONE.
Owner’s Manual Rev 1.0 Page 4 of 4 Products that may be enabled through the use of this TT4031 (SE-GM29) Wireless Modem product; (2) this TT4031 (SE- GM29) Wireless Modem product, if the serial numb.
Owner’s Manual Rev 1.0 Page 5 of 5 YOU ACKNOWLEDGE THAT THIS TT4031 (SE-GM29) WIRELESS MODEM PRODUCT MAY ALLOW YOU, AT Y OUR DISCRETION, TO RECEIVE WHERE AVAILABLE FROM A THIRD PARTY (SUCH AS YOUR D.
Owner’s Manual Rev 1.0 Page 6 of 6 The information contained in this document is the proprietary information of Sony Ericsson Mobile Communications International.
Owner’s Manual Rev 1.0 Page 7 of 7 Table of Content Part 1: Overview ............................................................................................................................... ... 12 1. Introduction .............................
Owner’s Manual Rev 1.0 Page 8 of 8 1.3 Error Codes ........................................................................................................................ 59 1.4 Examples on How to Use the AT Commands ...............................
Owner’s Manual Rev 1.0 Page 9 of 9 4.6 AT*ELAM Ericsson Local Audio Mode ..................................................................... 106 4.7 AT*EMIC Ericsson Microphone Mode .................................................................
Owner’s Manual Rev 1.0 Page 10 of 10 10.13 AT+ILRR Cable Interface Local Rate Reporting ............................................. 149 10.14 AT+IPR Cable Interface Port Command ............................................................ 150 10.15 AT*E2ESC M2M Escape Sequence Guard Time .
Owner’s Manual Rev 1.0 Page 11 of 11 13.16 AT+CSCS Select Character Set ............................................................................ 223 13.17 AT+CSMS Select Message Service ...........................................................
Owner’s Manual Rev 1.0 Page 12 of 12 Part 1: Overview.
Owner’s Manual Rev 1.0 Page 13 of 13 1. Introduction 1.1 Target Users TT4031 (SE-GM29) modems are designed to be integrated into machine- machine or man-to-machine communications applications. They are intended to be used by manufacturers, system integrators, applications developers and developers of wireless communications equipment.
Owner’s Manual Rev 1.0 Page 14 of 14 Part 3 - Using AT Commands This section lists all the AT commands relevant to the TT4031 (SE-GM29), including their associated parameters. The purpose of part 3 is to give you detailed information about the function of each command in the AT command set.
Owner’s Manual Rev 1.0 Page 15 of 15 2. TT4031 (SE-GM29) Modem 2.1 Description The dual band EGSM 900/1800 MHz TT4031 (SE-GM29) is a GSM/GPRS serial modem.
Owner’s Manual Rev 1.0 Page 16 of 16 RS232 9-way serial interface 5 V - 32 V DC input 4-wire audio connection Antenna connection (FME male) FCC and PTCRB approved 2.3 TT4031 (SE-GM29) in a Communication System Figure 2.1 illustrates the main blocks of a wireless communication system using the TT4031 (SE-GM29).
Owner’s Manual Rev 1.0 Page 17 of 17 ETSI specifies a set of AT commands for controlling the GSM element of the modem; these commands are supplemented by Sony Ericsson specific commands. To find out how to work with AT commands, see “Part 3: Using AT Commands”.
Owner’s Manual Rev 1.0 Page 18 of 18 2.4 Main Features and Services The modem performs a set of telecom services (TS) according to GSM standard phase 2+, ETSI and ITU-T. The services and functions of the modem are implemented by issuing AT commands over the RS232 serial interface.
Owner’s Manual Rev 1.0 Page 19 of 19 GSM network (for example, traffic reports). This feature is network dependent. SMS STATUS REPORT according to GSM 03.40. SMS COMMAND according to GSM 03.40. The maximum length of an SMS message is 160 characters when using 7- bit encoding.
Owner’s Manual Rev 1.0 Page 20 of 20 2.4.5 Fax The TT4031 (SE-GM29) allows fax transmissions to be sent and received by commercial software installed on the application computer.
Owner’s Manual Rev 1.0 Page 21 of 21 setting up and controlling communications to and from the GSM network; configuring the modem to communicate across the RS232 serial interface; and obtaining GSM network status information.
Owner’s Manual Rev 1.0 Page 22 of 22 2.5 Service and Support To contact customer support please use the details below: Customer Support Topp Consumer Products 3055 NW 84 th Avenue Miami, FL 33122 E-mail: telematic@toppcompanies.com Information about Topp Consumer Products and its products is available on the following web site: http ://www.
Owner’s Manual Rev 1.0 Page 23 of 23 3. Abbreviations Abbreviation Explanations AMR Adaptive M ulti Rate CBM Cell Broadcast Message CBS Cell Broadc ast Servic e CSD Circuit Switched Data DCE Data Ci.
Owner’s Manual Rev 1.0 Page 24 of 24 SMS Short Message Service TA Terminal Adapter TE Terminal Equipment TS Telecom Se rvices.
Owner’s Manual Rev 1.0 Page 25 of 25 Part 2: Integrating the Modem.
Owner’s Manual Rev 1.0 Page 26 of 26 1. Mechanical Description 1.1 Overview The pictures below show the mechanical design of the TT4031 (SE-GM29) along with the positions of the different connectors and mounting holes. The TT4031 (SE-GM29) case is made of durable PC/ABS plastic.
Owner’s Manual Rev 1.0 Page 27 of 27 The SIM card is mounted in the modem. The pins and electrical characteristics or the modem’s various connectors are described in Electrical Description.
Owner’s Manual Rev 1.0 Page 28 of 28 1.2 Physical Dimensions Measurements are given in millimeters. See also Technical Data ..
Owner’s Manual Rev 1.0 Page 29 of 29 2. Electrical Description All electrical connections to the TT4031 (SE-GM29) are designed to meet the standard air (4 kV) and contact (8 kV) discharge ESD tests, of EN 301 489-1.
Owner’s Manual Rev 1.0 Page 30 of 30 The power connector electrical characteristics are listed below: Pin Signal Dir Limits Description 1 VCC I 5 - 32 V Positive power input 2 - - - No connection 3 HR_IN I –0.
Owner’s Manual Rev 1.0 Page 31 of 31 Audio signal descriptions are listed below: Pin Signal Dir Description 1 MICN I Microphone negative input 2 BEARN O Earpiece negative output 3 BEARP O Earpiece positive output 4 MICP I Microphone positi ve input MICP and MICN are balanced differential microphone input signals.
Owner’s Manual Rev 1.0 Page 32 of 32 2.3 Antenna Connector The antenna connector allows transmission of radio frequency (RF) signals between the modem and an external customer-supplied antenna. The modem is fitted with a 50 Ω FME male coaxial jack as shown below.
Owner’s Manual Rev 1.0 Page 33 of 33 2.4 SIM Card Reader The TT4031 (SE-GM29) is fitted with a SIM card reader designed for 3 V and 5 V SIM cards. It is the flip-up type, which is lockable in the horizontal position and is accessed through a removable panel as shown below The SIM card reader includes a SIM presence switch.
Owner’s Manual Rev 1.0 Page 34 of 34 2.5 RS232 Serial Port The modem supports a standard RS232 serial interface (EIA/TIA 574) via its 9 pin Sub-D connector, shown below.
Owner’s Manual Rev 1.0 Page 35 of 35 2.5.1 Serial Data The modem supports the standard data character format of 1 start bit, 8 bit data, no parity plus 1 stop bit, in total 10 bits per character. 2.5.2 Serial Data Signals - RD, TD The default baud rate is 9.
Owner’s Manual Rev 1.0 Page 36 of 36 Data Terminal Ready (DTR) DTR indicates that the DTE is ready to transmit and receive data. It also acts as a hardware ‘hang-up’, terminating calls when switched high. The signal is active low. You can define the exact behaviour of DTR with an AT command.
Owner’s Manual Rev 1.0 Page 37 of 37 3. Operation 3.1 Switching On the Modem There are two ways to switch on the modem, once power is applied. either assert TO_IN high for > 0.2 s; or activate the RS232 control line DTR, high for > 0.2 s.
Owner’s Manual Rev 1.0 Page 38 of 38 3.4 Operating States/LED The modem has a green LED, as depicted below, which is used to indicate various operating states.
Owner’s Manual Rev 1.0 Page 39 of 39 4. Safety and Product Care Please read the information in th is section and the information in Installation of the Modem before starting your integration work. 4.1 Safety Instructions PLEASE READ THESE SAFETY INSTRUCTIONS AND KEEP A COPY OF THEM.
Owner’s Manual Rev 1.0 Page 40 of 40 The TT4031 (SE-GM29) must not be installed or located where the surface temperature of the plastic case may exceed 85ºC.
Owner’s Manual Rev 1.0 Page 41 of 41 Never connect more than one modem to a single antenna. The modem can be damaged by radi o frequency energy from the transmitter of another modem. Like any mobile station, the an tenna of the modem emits radio frequency energy.
Owner’s Manual Rev 1.0 Page 42 of 42 5. Installation of the Modem This chapter gives you advice and helpful hints on how to integrate the TT4031 (SE-GM29) into your application from a hardware perspective.
Owner’s Manual Rev 1.0 Page 43 of 43 5.1.3 Connection of Components to TT4031 (SE-GM29). The integrator is responsible for the final integrated system. Incorrectly designed or installed, external components may cause radiation limits to be exceeded.
Owner’s Manual Rev 1.0 Page 44 of 44 Caution! Do not exceed a torque of 2.2 in lb (25 Ncm) when tightening the fixings screws. Ex cessive torque applied to the screws can crack the plastic case.
Owner’s Manual Rev 1.0 Page 45 of 45 In any event, you should contact your local antenna manufacturer for additional information concerning antenna type, cables, connectors, antenna placement, and the surrounding area. You should also determine whether the antenna needs to be grounded or not.
Owner’s Manual Rev 1.0 Page 46 of 46 5.4.5 Possible Communication Disturbances Possible communication disturbances include the following: Noise can be caused by electronic devices and radio transmitters. Path-loss occurs as the strength of th e received signal steadily decreases in proportion to the distance from the transmitter.
Owner’s Manual Rev 1.0 Page 47 of 47 5.5 Attachments The TT4031 (SE-GM29) has been FCC certified using a number of attachments including: 1._ AC-DC Power Adaptor with Customized DC Lead (Model # PS001) Input 100-240 Va.c., 50/60Hz, 2m mains lead Output: 12 Vd.
Owner’s Manual Rev 1.0 Page 48 of 48 6. Technical Data Data Features CSD Up to 9.6 kbps HSCSD (2+1) Up to 19.2 kbps GPRS Class B (4+1) - P channels - Coding schemes CS1 - CS4 85.
Owner’s Manual Rev 1.0 Page 49 of 49 Power Supply Supply voltage range 5 - 32 V d.c. Power Consumption Supply voltage 5V 12V 32V Vdc Power Down Mode Av Max Av Max Av Max 5 15 5 15 20 50 µA Standby .
Owner’s Manual Rev 1.0 Page 50 of 50 Radio Specifications Frequency range TT4031 (SE-GM29): EGSM 900 MHz and 1800 MHz (dual band) Maximum RF output power 2 W (900 MHz) and 1 W (1800 MHz) Antenna imp.
Owner’s Manual Rev 1.0 Page 51 of 51 Mechanical Specification Length 77.4 mm Width 66.4 mm Height 26.2 mm Weight < 130 g Environmental specifications Operating temperature range –25 °C to +55 °C Storage temperature range –40 °C to +85 °C Relative h umidity 5 - 95 %, non-condensing Stationary vibration, sinusoidal Displacement: 7.
Owner’s Manual Rev 1.0 Page 52 of 52 Certification FCC Certificat ion Part 15 Part 22 Part 24 Approved to PTCRB according to NAPRD.03 and GS M 3GPP TS 51.
Owner’s Manual Rev 1.0 Page 53 of 53 7. FCC Certificate.
Owner’s Manual Rev 1.0 Page 54 of 54 Part 3: Using AT Commands.
Owner’s Manual Rev 1.0 Page 55 of 55 1. Introduction to AT Commands 1.1 Overview AT commands, issued from a computer in your application are used to control and implement the functions of the modem.
Owner’s Manual Rev 1.0 Page 56 of 56 < > The term enclosed in angle brackets is a syntactical element. The brackets do not appear in the command line. [ ] Square brackets are used to indicate that a certain item is optional. For example, su b-parameters of a command or an optional part of a re sponse.
Owner’s Manual Rev 1.0 Page 57 of 57 A version of the basic syntax is: AT<command><parameter> Extended Syntax Command AT+<command>= [<parameter>] AT*<command>=[.
Owner’s Manual Rev 1.0 Page 58 of 58 If the indicated <parameter> is not recognized, the result code ERROR is issued. NOTE! - Possible responses are indicated both as <command>:(list of supported <parameter>) and (in most cases) the actual range of the parameter values.
Owner’s Manual Rev 1.0 Page 59 of 59 Value General meaning OK Command executed, no errors ERROR Invalid command or command line too long NO DIALTONE No dialing possible, wrong mode BUSY Remote stati.
Owner’s Manual Rev 1.0 Page 60 of 60 14 SIM busy 15 SIM wrong 16 Incorrect password 17 SI M PIN2 required 18 S IM PUK2 required 20 Memory full 21 Invalid index 22 Not found 23 Memory fai lure 24 Tex.
Owner’s Manual Rev 1.0 Page 61 of 61 The syntax is as follows: +CMS ERROR: <err> Values for the <err> parameter are described in the following table. <err> Description 0 - 127 GSM 04.11 Annex E-2 values 128 - 255 GS M 03.40 subclause 9.
Owner’s Manual Rev 1.0 Page 62 of 62 1.4 Examples on How to Use the AT Commands After every group of AT commands there is a section where some of the more complicated commands are exemplified.
Owner’s Manual Rev 1.0 Page 63 of 63 Call Control 2.1 AT+CPIN PIN Control See 3.23, AT+CPIN PIN Control 2.2 ATA Answer Incoming Call Description Command Possible Responses Answer an incoming call ATA •_ CONNECT •_ CONNECT <text> •_ NO CARRIER •_ ERROR •_ OK Answer and initiate connection to an incoming call.
Owner’s Manual Rev 1.0 Page 64 of 64 2.3 ATD Dial Description Command Possible Responses •_ Originate a call a nd dial the phone numbe r spec ified in the command as <dial_str ing> or •_ D.
Owner’s Manual Rev 1.0 Page 65 of 65 If the dial string is omitted, and the semicolon included, the command instructs the ME to do a network detect. If the network is available OK is returned. Abortability: Aborting an ATD command is accomplished by the transmission from the DTE to the DCE of any character.
Owner’s Manual Rev 1.0 Page 66 of 66 9600 Connected with data bit rate of 9600 bits/s 4800 Connected with data bit rate of 4800 bits/s 2400 Connected with data bit rate of 2400 bits/s 2.4 ATH Hang up Description Command Possible Responses Termin ate t he call ATH •_ ERROR •_ OK Signals the MS to terminate an active call.
Owner’s Manual Rev 1.0 Page 67 of 67 Command is ignored, and is implemented for compatibility only. It would normally cause the next D command to use pulses when dialling the number.
Owner’s Manual Rev 1.0 Page 68 of 68 NOTE! - If there is no network available the <n> parameter will decide if “NO DIALTONE” or “NO CARRIER” will be returned. If the call recipient is busy, the <n> parameter will decide if “BUSY” or “NO CARRIER” will be returned.
Owner’s Manual Rev 1.0 Page 69 of 69 When single mode is selected the call originating and hang-up procedures are similar to procedures specified in ITU-T Recommendations V.25ter, T.31 and T.32. In GSM there can be voice followed by data (refer to GSM 02.
Owner’s Manual Rev 1.0 Page 70 of 70 <mode> Description 0 “Drop DTR” ignored but OK response given. ATH disconnects 1 “Drop DTR” and ATH ignored but OK response given 2 “Drop DTR” behavior according to &D setting. ATH disconnects.
Owner’s Manual Rev 1.0 Page 71 of 71 Control and Status 3.1 ATQ Result Code Suppression Description Command Possible Responses Set Result Code Suppression ATQ[=]<value> •_ OK •_ ERROR Read.
Owner’s Manual Rev 1.0 Page 72 of 72 <rcnt> Description 0 Disable automatic answer. Default va lue 1-7 Answer after the specifi ed number of rings 3.
Owner’s Manual Rev 1.0 Page 73 of 73 3.4 ATS3 Command Line Termination Character Description Command Possible Responses Set Command Line Termination Character ATS3=<value> •_ OK •_ ERROR R.
Owner’s Manual Rev 1.0 Page 74 of 74 This S-parameter represents the decimal IA5 value of the character generated by the DCE as part of the header, trailer, and terminator for result codes and information text, along with the S3 parameter (see the description of the V parameter for usage).
Owner’s Manual Rev 1.0 Page 75 of 75 Blind dial de lay contr ol ATS6=[<dly>] OK Read the current setting ATS6? <dly> Show if the comman d is supported ATS6=? S6: (list of supported <dly>s) Included for compatibility. No functionality <dly> Description 2 Wait two seco nds be fore blin d dialing .
Owner’s Manual Rev 1.0 Page 76 of 76 ATS8 Comma Dial Modifier Delay Control Description Command Possible Responses Set Comma Dial Modifier Delay Control ATS8=[<dly>] •_ OK •_ ERROR Read the current setting. ATS8? <dly> Show if the comman d is supported.
Owner’s Manual Rev 1.0 Page 77 of 77 3.11 AT*ECAM Ericsson Call Monitoring Description Command Possible Responses Set Call Monitoring on or off AT*ECAM=<onoff> •_ OK •_ +CME ERROR: <err.
Owner’s Manual Rev 1.0 Page 78 of 78 3.12 AT*EDST Ericsson Daylight Saving Time Description Command Possible Responses Set Daylight Saving Time AT*EDST=<dst> •_ +CME ERROR: <err> •_ .
Owner’s Manual Rev 1.0 Page 79 of 79 Perform a master reset in the MS AT*EMAR=<phone lock code> •_ +CME ERROR: <err> •_ OK •_ ERROR Shows if the command is supported or not AT*EMAR=? •_ +CME ERROR: <err> •_ OK •_ ERROR This command requests the MS to reset user data.
Owner’s Manual Rev 1.0 Page 80 of 80 1 Request for report on inserted PIN code is activated (on) 3.15 AT+CCLK Set Clock and Date Description Command Possible Responses Set the real time clock of the.
Owner’s Manual Rev 1.0 Page 81 of 81 Show if the comman d is supported AT+CEER=? •_ OK •_ ERROR Causes the TA to return one or more lines of information text <report>. Typically, the text will consist of a single line containing the failure information given by the GSM network in text format.
Owner’s Manual Rev 1.0 Page 82 of 82 <fun> Description 0 Minimum functionality. Modem is OFF 1 Full func tionality. Mo dem is ON 3.18 AT+CIND Indicator Control Description Command Possible Res.
Owner’s Manual Rev 1.0 Page 83 of 83 Integer type Value shall be in range of corresponding <descr> <descr> Description “signal” Signal quality (0-5) “service” Service availab ili.
Owner’s Manual Rev 1.0 Page 84 of 84 •_ ERROR Show if the comman d is supported AT+CMEE=? •_ +CMEE: (list of supported <n>s) •_ OK •_ ERROR Disables or enables the use of result code +CME ERROR: <err> as an indication of an error relating to the functionality of the ME.
Owner’s Manual Rev 1.0 Page 85 of 85 Enables or disables the sending of unsolicited result codes from ME to TE in the case of key pressings, display changes, and indicator state changes. <mode> controls the processing of unsolicited result codes specified within this command.
Owner’s Manual Rev 1.0 Page 86 of 86 Test if the command is supported AT+CPAS=? •_ +CPAS: (list of s uppor ted <pas>s) •_ +CME ERROR <err> •_ OK •_ ERROR Returns the activity status <pas> of the ME. It can be used to interrogate the ME before requesting action from the phone.
Owner’s Manual Rev 1.0 Page 87 of 87 3.23 AT+CPIN PIN Control Description Command Possible Responses Request PIN Control AT+CPIN=<pin>[,<new pin>] •_ +CME ERROR: <err> •_ OK .
Owner’s Manual Rev 1.0 Page 88 of 88 SIM PIN ME is wai ting SIM PIN to be given SIM PUK ME is wai ting SIM PUK to be given PH-SIM PIN ME is waiting PHone-to-SIM card password to be given SIM PIN2 ME is waiting SI M PIN2 t o be given .
Owner’s Manual Rev 1.0 Page 89 of 89 Reque st facility lo ck AT+CPWD=<fac>, <oldpwd>, <newpwd> •_ +CME ERROR <err> •_ OK •_ ERROR Show if the comman d is supported AT+C.
Owner’s Manual Rev 1.0 Page 90 of 90 <newpwd> Description string type <newpwd> is the new password, maximum length of password can be determin ed with <pwdlength> <pwdlength>.
Owner’s Manual Rev 1.0 Page 91 of 91 Read current setting AT+CR? •_ +CR: <mode> •_ OK •_ ERROR Test if the command is supported AT+CR=? •_ +CR: (list of supported <mode>s) •_ OK •_ ERROR Enables or disables display of intermediate bearer capability reports during the handshake phase.
Owner’s Manual Rev 1.0 Page 92 of 92 When enabled, an incoming call is indicated to the TE with unsolicited result code +CRING: <type> instead of the normal RING.
Owner’s Manual Rev 1.0 Page 93 of 93 3.28 AT+CSQ Signal Strength Description Command Possible Responses Execute Signal Strength AT+CSQ •_ +CSQ: <rssi>,<ber> •_ +CME ERROR <err>.
Owner’s Manual Rev 1.0 Page 94 of 94 Enable and disable automatic time zone update via NITZ AT+CTZU=<onoff> •_ +CME ERROR: <err> •_ OK •_ ERROR Read current setting AT+CTZU? •_ +.
Owner’s Manual Rev 1.0 Page 95 of 95 Audio AT*E2EAMS and AT*E2APR are new commands that replace the funtionality offered by the *EALR, *EAMS, *EARS and *ELAM commands. Use the new commands in new applications. The old commands are included for compatibility.
Owner’s Manual Rev 1.0 Page 96 of 96 configured. There are several audio profiles available in non-volatile storage, and the current profile can be modified by use of the AT*E2APR command.
Owner’s Manual Rev 1.0 Page 97 of 97 1 Set <TxPGA> 2 Set <RxPGA> 3 Set <SideToneGain> 4 Set <AuxInGain> 5 Set <MicI nGain> 6 Set <TxAGC> 7 Set <Volume> 8 Se.
Owner’s Manual Rev 1.0 Page 98 of 98 0 10 dB 1 13 dB 2 16 dB 3 19 dB 4 22 dB 5 25 dB <AuxInputGain> Description 0 MUTE 1 13 dB 2 34 dB 3 46 dB <MicInputGain> Description 0 MUTE 1 13 dB 2.
Owner’s Manual Rev 1.0 Page 99 of 99 0 13 bit PCM 1 16 bit PCM <HFAlgorithm> Description 0 No handsfree 1 Advanced handsfree 2 Switching h andsfr ee 3 No handsfree handheld 4 No handsfree exte.
Owner’s Manual Rev 1.0 Page 100 of 100 Examples AT*E2EAMS=? *E2EAMS=(0-21,255) OK Current default profile is 0: AT*E2EAMS? *E2EAMS: 2,2,3,2,3, 2,5,9,3,3,0,1,0, 0,0,1,1,1,1,1,1 OK Sets current profil.
Owner’s Manual Rev 1.0 Page 101 of 101 Display currently set p rofile AT*E2APR? •_ *E2APR: current <prnum> •_ ERROR Shows if the command is supported AT*E2APR=? •_ *E2APR: (li st of supp.
Owner’s Manual Rev 1.0 Page 102 of 102 •_ Examples AT*E2APR=? *E2APR= (0-4),(0-2),(0-2) OK Current default profile is profile 0: AT*E2APR? *E2APR: 0 OK Set audio profile now used to profile 1: AT*.
Owner’s Manual Rev 1.0 Page 103 of 103 Show list of supported parameters AT*EALR=? *EALR:(list of supported <mode>s, <activation >s and <aud_status>s parameters) Included for compatibility.
Owner’s Manual Rev 1.0 Page 104 of 104 Sets the audio mode for the applic ation AT*EAMS=<internal_voice_al g>[,<noise_reduction> [,<side tone> [,<short_echo_canceling> [,<.
Owner’s Manual Rev 1.0 Page 105 of 105 <short_echo_canceling> Description 0 Off 1 On <ATMS_gain> Description 0 Normal (0 dB) (internal voice processi ng) <Class> Description 0 None.
Owner’s Manual Rev 1.0 Page 106 of 106 <mode> Description 0 Disable analogue ring signal 1 Enable analogue ring signal 4.6 AT*ELAM Ericsson Local Audio Mode Description Command Possible Respon.
Owner’s Manual Rev 1.0 Page 107 of 107 Enables/disables the phone microphone AT*EMIC=<mode> •_ +CME ERROR: <err> •_ OK •_ ERROR Test if the command is supported, show supported val.
Owner’s Manual Rev 1.0 Page 108 of 108 1 On, music mute indication re sult cod es will be se nt to the accessory <resp> Description 0 Music mute inactive 1 Music mute active 4.
Owner’s Manual Rev 1.0 Page 109 of 109 1 Audio volume over AFMS is output at maximum level that is no clipp ing occurs . An extern al accessory such as a vehicle kit controls the actual volume level.
Owner’s Manual Rev 1.0 Page 110 of 110 Data - CSD/HSCSD NOTE! - Since the modem does not support V42bis compression the following commands have not been implemented: •_ AT+DS •_ AT+DR 5.
Owner’s Manual Rev 1.0 Page 111 of 111 12 9600 bps V.34 15 19200 bps V.34 68 2400 bps V.110 (ISDN) 70 4800 bps V.110 (ISDN) 71 9600 bps V.110 (ISDN) 75 14400 bps V.110 (ISDN) 79 19200 bps V.110 (ISDN) 80 28800 bps V.110 (ISDN) 81 38400 bps V.110 (ISDN) 82 48000 bps V.
Owner’s Manual Rev 1.0 Page 112 of 112 Test if the command is supported AT+CRLP=? •_ +CRLP: (list of supported <iws>s), (list of supported <mws>s), (list of supported <T1>s), (li.
Owner’s Manual Rev 1.0 Page 113 of 113 <T4> Description 5 3 - 255 Re-sequencing period T4 (*10 ms) <ver> Description Integer RLP ve rsion.
Owner’s Manual Rev 1.0 Page 114 of 114 Data - GPRS 6.1 AT+CGACT PDP Context Activate or Deactivate Description Command Possible Responses Activate or deactivate the specified PDP context(s) +CGACT=[.
Owner’s Manual Rev 1.0 Page 115 of 115 Integer type A numeric p aramete r which spe cifies a s pecific P DP context definition 6.2 AT+CGATT GPRS Attach or Detach Description Command Possible Respons.
Owner’s Manual Rev 1.0 Page 116 of 116 6.3 AT+CGDATA Enter Data State Description Command Possible Responses Establish GPRS/packet domain connection +CGDATA=[<L2p>,[cid[ ,cid>[,…]]]] •_.
Owner’s Manual Rev 1.0 Page 117 of 117 Test if the command is supported +CGDCONT=? •_ +CGDCONT: (range of supported <cid>s), <PDP_type>,,,(list of supported <d_comp>s), (list of .
Owner’s Manual Rev 1.0 Page 118 of 118 String type A string parameter that identifies the MS in the address space applicable to the PDP. If the val ue is null or omitte d, then a va lue may be p rov.
Owner’s Manual Rev 1.0 Page 119 of 119 Enables or disables the sending of unsolicited result codes, +CGEV: XXX from MS to TE in the case of certain events occurring in the GPRS/packet domain MS or the network. <mode> Description 0 Buffer unsolicited result codes in the MS.
Owner’s Manual Rev 1.0 Page 120 of 120 Integer type Parameter whic h specifie s a part icular PDP context definition (see +CGDCONT command). If no <cid> is specified, the addresses for all defined contexts are returned <PDP_address> Description String type A stri ng that identifies the MS in the address space applicable to the PDP.
Owner’s Manual Rev 1.0 Page 121 of 121 •_ OK •_ ERROR Allows the TE to specify a minimum acceptable profile which is checked by the MS against the negotiated profile returned in the Activate PDP Context Accept message. The set command specifies a profile for the context identified by the (local) context identification parameter, <cid>.
Owner’s Manual Rev 1.0 Page 122 of 122 <reliability> Description 0 Subscribed (from network) value used 1-5 Re liability class <peak> Description 0 Subscribed (from network) value used 1.
Owner’s Manual Rev 1.0 Page 123 of 123 14 1 000 000 (~2.2 kbits/s) 15 2 000 000 (~4.4 kbits/s) 16 5 000 000 (~11.1 kbits/s) 17 10 000 000 (~22 kbits/s) 18 20 000 000 (~44 kbits/s) 31 50 000 000 (~111 kbits/s) 6.
Owner’s Manual Rev 1.0 Page 124 of 124 that is used in the +CGDCONT command, the +CGQREQ command is effectively an extension to the +CGDCONT command.
Owner’s Manual Rev 1.0 Page 125 of 125 7 Up to 64 000 (512 kbits/s) 8 Up to 128 000 (1 024 kbits/s) 9 Up to 256 000 (2 048 kbits/s) <mean> Description 0 Subscribed (from network) value used 1 Best effort 2 100 (~0.22 bits/s) 3 200 (~0.44 bits/s) 4 500 (~1.
Owner’s Manual Rev 1.0 Page 126 of 126 Read the current settings AT+CGREG? •_ +CGREG: <n>,<stat>[,<lac>, <ci>] •_ +CME ERROR: <err> •_ OK •_ ERROR Test if the c.
Owner’s Manual Rev 1.0 Page 127 of 127 <lac> Description String type Two byte location area code in hexadecimal format Note!_ <ci> Description String type Two byte cell ID in he xadecimal fo rmat Note!_ 6.
Owner’s Manual Rev 1.0 Page 128 of 128 Data - HSCSD 7.1 AT+CHSC HSCSD Current Call Parameters Description Command Possible Responses Show current HSCSD call parameters AT+CHSC •_ +CHSC:<rx>,.
Owner’s Manual Rev 1.0 Page 129 of 129 <coding> Description 0 No HSCSD call is active. See a lso note 4 Current channel coding is 9.6 kbits/s (TCH/F9.
Owner’s Manual Rev 1.0 Page 130 of 130 <codings> Description 4 Indicates that the accepted channel coding for the next establis hed no n-trans parent HSCSD call is 9.6 kbits/s only 7.3 AT+CHSN HSCSD Non Transparent Call Configuration Description Command Possible Responses Set HSCSD configuration.
Owner’s Manual Rev 1.0 Page 131 of 131 0 TA/M E shall calcu late a pro per numb er of re ceive timeslots from currently selected fi xed network user rate (<speed> parameter from +CBST command, and <codings>, and <wRx> (or <maxRx> from +CHSD command if <wRx>=0) 1 Wanted air interface user rate is 9.
Owner’s Manual Rev 1.0 Page 132 of 132 Set HSCSD parameters reporting on or off AT+CHSR=[<mode>] •_ +CME ERROR: <err> •_ OK •_ ERROR Show current setting AT+CHSR? •_ +CHSR: <m.
Owner’s Manual Rev 1.0 Page 133 of 133 7.5 AT+CHSU HSCSD Automatic User Initiated Upgrading Description Command Possible Responses Set HSCSD automatic user in itiated upgr ading on or off AT+CHSU=[&.
Owner’s Manual Rev 1.0 Page 134 of 134 Fax 8.1 AT*E2FAX Ericsson M2M Fax Comm. Baud Rate Modification Description Command Possible Responses Request change of fax comm.
Owner’s Manual Rev 1.0 Page 135 of 135 Examples AT*E2FAX=? *E2FAX= (0-1) OK AT*E2FAX? *E2FAX: 0 (Current default setting is 19200 baud) OK AT*E2FAX=0 OK (Sets default RS232 setting to 9600 baud) 8.2 Low Level Fax Commands The following table of low level fax commands are supported and used by the TT4031 (SE-GM29) for fax operation.
Owner’s Manual Rev 1.0 Page 136 of 136 Identification 9.1 AT Attention Command Description Command Possible Responses Checks the communication between the MS and application AT •_ OK •_ +CME ERROR <err> This command is used to determine the presence of an MS.
Owner’s Manual Rev 1.0 Page 137 of 137 < pr> Description 0 Stores current settings in User Profi le 0 9.4 AT* List all Supported AT Commands Description Command Possible Responses List all imp.
Owner’s Manual Rev 1.0 Page 138 of 138 Request the model identification AT+CGMM •_ <model type> <model name> •_ +CME ERROR: <err> Show if the comman d is supported AT+CGMM=? •_ OK •_ ERROR Causes the MS to return one or more lines of information text <model>, determined by the MS manufacturer.
Owner’s Manual Rev 1.0 Page 139 of 139 9.8 AT+CGSN Read MS Product Serial Number Identification Description Command Possible Responses Request product serial number AT+CGSN •_ <sn> •_ +CME.
Owner’s Manual Rev 1.0 Page 140 of 140 5 Active settings 7 Mode m configur ation prof ile (brief lis ting of the modem functionality: fax classes, Bluetooth, IrDA, modem type, etc.
Owner’s Manual Rev 1.0 Page 141 of 141 Interface 10.1 AT+CPIN PIN Control See 3.23, AT+CPIN PIN Control 10.2 AT&C Circuit 109 (DCD) Control Description Command Possible Responses Set behavior of carrier detect AT&C[<value>] OK ERROR Determines the behaviour of the carrier detect.
Owner’s Manual Rev 1.0 Page 142 of 142 10.4 AT&S Circuit 107 (DSR) Response Description Command Possible Responses Set behaviour of data set ready AT&S[<value>] •_ OK •_ ERROR Determines the behaviour of the data set ready signal. <value> Description 0 DSR always on 1 DSR on in data mode.
Owner’s Manual Rev 1.0 Page 143 of 143 10.6 ATE Command Echo Description Command Possible Responses Request Command Echo ATE[<value>] ATE=[<value>] •_ OK •_ ERROR Show the current se.
Owner’s Manual Rev 1.0 Page 144 of 144 0 Display numeric result codes 1 Di splay verbose result codes. Default va lue List of result codes ATV1/ATV=1 ATV0/ATV=0 Description OK 0 Acknowledges executi.
Owner’s Manual Rev 1.0 Page 145 of 145 Show if supported and list availa ble par ameter range ATZ=? Z: (list of suppo rted <profile>s) This command instructs the DCE to set all parameters to their default values as specified by the user.
Owner’s Manual Rev 1.0 Page 146 of 146 The default values for the parameters below are for “no transparency” and “only UIH frames used”. <transparency> Description 0 No transparency &l.
Owner’s Manual Rev 1.0 Page 147 of 147 10 10 s default timer <k> Description 1..7 Window size 10.10 AT+CRES Restore SMS Settings Description Command Possible Responses Restore settings AT+CRES.
Owner’s Manual Rev 1.0 Page 148 of 148 Read the current setting AT+ICF? •_ +ICF: <format>,<parity> •_ OK •_ ERROR Show if the command is supported AT+ICF=? •_ +ICF: (l ist of sup.
Owner’s Manual Rev 1.0 Page 149 of 149 <by_te> Description 0 No flow control on DTE 1 Xon/Xoff flow control on DCE. Control characters are removed by the DCE interface 2 RTS flow control on DCE.
Owner’s Manual Rev 1.0 Page 150 of 150 1 Enables repor ting of lo cal port rate (+I LRR: is transmitted) 10.14 AT+IPR Cable Interface Port Command Description Command Possible Responses Defines fixe.
Owner’s Manual Rev 1.0 Page 151 of 151 10.15 AT*E2ESC M2M Escape Sequence Guard Time Description Command Possible responses Set GPR S online command guard time AT*E2ESC=[<gt>] •_ OK •_ ERR.
Owner’s Manual Rev 1.0 Page 152 of 152 Network 11.1 AT*E2CD Ericsson M2M Cell Description Description Command Possible Responses Request network cell description AT*E2CD=<n> •_ ERROR •_ OK.
Owner’s Manual Rev 1.0 Page 153 of 153 string type Two byte cell ID in hexa decimal form at <ta> Description 0-63 According to GSM 04. 18 V8.6.0, the coding of the timing advance value is the binary representation of the ti ming advance in bit periods; 1 bi t period = 48/13 ìs.
Owner’s Manual Rev 1.0 Page 154 of 154 OK Verbose mode. The firs t cell is t he servin g cell a nd the rest are neighb our ce lls as provided by the network in the system info.
Owner’s Manual Rev 1.0 Page 155 of 155 Examples AT*E2EMM=1 *E2EMM:<CR><LF> Serving Cell<CR><LF> MCC,MNC,LAC,CellID,BSIC,Ch[,RxL,C1,C2][,RxLFull,RxLSub, RxQFull,RxQSub,TA,TN]&.
Owner’s Manual Rev 1.0 Page 156 of 156 AT*E2EMM=7 *E2EMM:<servcell mcc>,<servcell mnc>,<servcell lac>, <servcell ci>,<servcell bsic>,<servcell ch>[,<servcell r.
Owner’s Manual Rev 1.0 Page 157 of 157 8 As n=7 fo rmat bu t there will be cont inuous uns olicited information responses <m> seconds apart <m> Description 1-255 Integer type giving time (in seconds) between unsol icited responses. Default value is 5 <mcc> Description Integer type Three digits in decimal format.
Owner’s Manual Rev 1.0 Page 158 of 158 Integer type Received Signal Stre ngth leve l in dBm. The R x Level is taken in the Downlink and stati stically is appli ed to 100 TDMA frames of the TCH or during a SACCH multiframe <rxlsub> Description Integer type Received Signal Stre ngth leve l in dBm.
Owner’s Manual Rev 1.0 Page 159 of 159 7 BER > 15.0 % <c1> Description Integer Path L oss crite rion par ameter fo r neighb our cells . The MS calculates this para meter, in id le mode, to decide if t he cell is suit able to c amp on. Afte r the ca lculation t he criterion is C1 > 0.
Owner’s Manual Rev 1.0 Page 160 of 160 <spi> Description String String type field of maximum length 16 bytes; character set as specified by command Select TE character set +CSCS 11.
Owner’s Manual Rev 1.0 Page 161 of 161 Test if the command is supported AT*ECSP=? •_ +CME ERROR: <err> •_ OK •_ ERROR This command is used to read the customer service profile (CSP) from the SIM. CSP is a list on the SIM, which indicates the services that are user accessible.
Owner’s Manual Rev 1.0 Page 162 of 162 This command is used to read the SIM preferred list of networks (EF PLMNSEL ). <index1> Description integ er Start index (>0) <index2> Descripti.
Owner’s Manual Rev 1.0 Page 163 of 163 <index> Description Integer Index to entry in SIM preferred list. The SIM preferred list contains at l east 8 positions according to GSM 11.11 <format> Description 2 Numeric <oper> <oper> Description String String indicates the code for the operator.
Owner’s Manual Rev 1.0 Page 164 of 164 where the raw data contained in the ICCid field on the SIM is 984411003605234207F7. Test command: AT*E2SSN=? OK 11.
Owner’s Manual Rev 1.0 Page 165 of 165 Integer Maximum number of characters to use in <name> string (20) 11.10 AT+CIMI Subscriber Identification Description Command Possible Responses Read IMS.
Owner’s Manual Rev 1.0 Page 166 of 166 The command is used to lock, unlock or interrogate an ME or a network facility <fac>. A password is normally needed to carry out such actions. Call barring facilities are based on GSM supplementary services (refer to GSM 02.
Owner’s Manual Rev 1.0 Page 167 of 167 <status> Description 0 Not active 1 Active <passw> Description string type Is the same as passw ord spec ified for the facility from the ME user in.
Owner’s Manual Rev 1.0 Page 168 of 168 Show if the command is supported AT+CNUM=? •_ +CME ERROR: <err> •_ OK •_ ERROR This command returns the MSISDNs related to the subscriber (this information can be stored in the SIM or in the ME).
Owner’s Manual Rev 1.0 Page 169 of 169 11.13 AT+COLP Connected Line Identification Presentation Description Command Possible Responses Request connected line identification presentation AT+COLP=[<.
Owner’s Manual Rev 1.0 Page 170 of 170 Intermediate Result codes: +COLP: <number>,<type>[,<subaddr>,<satype> [,<alpha>]] 11.
Owner’s Manual Rev 1.0 Page 171 of 171 0 Automatic (<oper> field is ignored) 1 Short format alphanumeric <oper> 2 Numeric <oper> <oper> Description string type Format determined by the <format> setting <stat> Description 0 Unknown 1 Availabl e 2 Current 3 Forbidden 11.
Owner’s Manual Rev 1.0 Page 172 of 172 Controls the presentation of the unsolicited result code +CREG. <n> Description 0 Disable network registration unsolici ted result code.
Owner’s Manual Rev 1.0 Page 173 of 173 Test command gives the current value of the <switch> parameter, informing if the indicator is enabled or disabled. The ciphering indicator feature may be disabled by the home network operator setting data in the “administrative data” field (EFAD) in the SIM as defined in GSM 11.
Owner’s Manual Rev 1.0 Page 174 of 174 11.17 AT*E2NBTS Ericsson M2M Neighbour BTS Description Command Possible Responses Set Neighbour Cells to monitor AT*E2NBTS=<ch1>,<bsic1>[,<c h2&.
Owner’s Manual Rev 1.0 Page 175 of 175 (0-1023) It represents the ARFCN that shows the Absolute RF Channel, which identifies a BCCH carrier <mcc> Description String Type Three digits in decimal format.
Owner’s Manual Rev 1.0 Page 176 of 176 Phonebook 12.1 AT*E2PBCS Ericsson M2M Phonebook Check Sum Description Command Possible Responses Request phone book checksum AT*E2PBCS •_ *E2PBCS: <cks>.
Owner’s Manual Rev 1.0 Page 177 of 177 •_ ERROR This command adds a contact or a phone number to the current group. <gindex> Description 1-10 The group index withi n the hierarchical phone book <type> Description 1 Contact 2 Phone number <itemindex> Description Integer The index of the contact/group/phone number to add.
Owner’s Manual Rev 1.0 Page 178 of 178 <name> Description String The group name. Character set as specified by command Select TE Character Set (AT+CSCS) <maxnamelength> Description integ er The maximum length of the grouping (bytes) 12.
Owner’s Manual Rev 1.0 Page 179 of 179 0 Settings for a credit card call (<passwd>, <indexn>, <asn>,<type>,<name>,<vercode> [,<send order>]). The four (4) parameters (<passwd>, <indexn>, <asn>, <vercode>) are mandatory wh en <mode>=0.
Owner’s Manual Rev 1.0 Page 180 of 180 String Character string of the name tag, for M&M. Maximum of 18 characters •_ <vercode> Description String Character string <0..9,#,*>. Maximum of 20 characters •_ <send order> Description 1 Verification code first.
Owner’s Manual Rev 1.0 Page 181 of 181 •_ ERROR Show if the comman d is supported AT*ESDI=? •_ +CME ERROR: <err> •_ OK •_ ERROR The command deletes the item with <index> in the group with <gindex>.
Owner’s Manual Rev 1.0 Page 182 of 182 12.8 AT*EGIR Ericsson Group Item Read Description Command Possible Responses Lists the items in the <gindex> group AT*EGIR=<gindex> •_ *EGIR: <i ndex1>, <type1>,<itemindex> [<CF><LF><index2>, <type2>, <itemindex> [.
Owner’s Manual Rev 1.0 Page 183 of 183 •_ ERROR Test if the command is supported and show possible settings AT*ESNU=? •_ *ESNU: (list of supported <type>s) •_ +CME ERROR: <err> •_ OK •_ ERROR Read the current setting AT*ESNU? •_ *ESNU: <type 1>, <number 1>, <number type 1> <CR><LF> ….
Owner’s Manual Rev 1.0 Page 184 of 184 12.10 AT+CPBF Phonebook Find Description Command Possible Responses Shows the current setting +CPBF=<findtext> •_ +CPBF: <index1>,<number>,<type >,<text>[[.
Owner’s Manual Rev 1.0 Page 185 of 185 Test if the command is supported +CPBR=? •_ +CPBR: (list of supported <index>s),<nlength>,<tlength> •_ +CME ERROR <err> •_ OK •_ ERROR Returns phone book entries in location number range <index1>.
Owner’s Manual Rev 1.0 Page 186 of 186 integer type Value indicating the maximum length of fiel d <text> 12.12 AT+CPBS Phone Storage Description Command Possible Responses Set phone book stora.
Owner’s Manual Rev 1.0 Page 187 of 187 String type Represents the password requi red when selecting password protected <storage>s, for example PIN2 for storage “ME” 12.
Owner’s Manual Rev 1.0 Page 188 of 188 145 ISDN/telephony numbering pl an, international number 161 ISDN/telephony numberi ng plan, national number 128-255 Other values refer GSM 04.
Owner’s Manual Rev 1.0 Page 189 of 189 Short Message Services - Point to Point 13.1 AT+CPIN PIN Control See 3.23, AT+CPIN PIN Control 13.2 AT+CGSMS Select Service for MO SMS Messages See 6.
Owner’s Manual Rev 1.0 Page 190 of 190 Selects memory storage <mem1>, <mem2> and <mem3> to be used for reading, writing, etc. If chosen storage is not appropriate for the ME (but is supported by the TA), final result co de +CMS ERROR: <err> is returned.
Owner’s Manual Rev 1.0 Page 191 of 191 13.4 AT+CSCA Service Centre Address Common for both PDU and Text Modes Description Command Possible Responses Set service centre address AT+CSCA=<sca> [,.
Owner’s Manual Rev 1.0 Page 192 of 192 13.5 AT+CMGF Message Format Common for both PDU and Text Modes Description Command Possible Responses Set message format AT+CMGF=<mode> •_ OK •_ ERRO.
Owner’s Manual Rev 1.0 Page 193 of 193 Show if the comman d is supported AT+CMGW=? •_ OK •_ ERROR Stores a message to memory storage <mem2>. Memory location <index> of the stored message is returned. By default message status will be set to ‘stored unsent’, but pa rameter <stat> allows other status values to be given.
Owner’s Manual Rev 1.0 Page 194 of 194 Write message to memory AT+CMGW [=<oa/da> [,<tooa/toda>[,<stat>]] ] <CR> Text is entered <ctrl- Z/ESC> •_ +CMGW: <index> .
Owner’s Manual Rev 1.0 Page 195 of 195 <toda> Description String type GSM 04. 11 TP-Destination- Address Type-of-Address octet in integer format (when first character of <da> is +(IRA 43.
Owner’s Manual Rev 1.0 Page 196 of 196 The DCD signal is in the ON state as PDU is given. The echoing of given characters back from the TA is controlled by V.
Owner’s Manual Rev 1.0 Page 197 of 197 Sends a message from a TE to the network (SMS-SUBMIT). Message reference value <mr> is returned to the TE on successful message delivery. Optionally, when AT+CSMS <service> value is 1 and there is network support, <scts> is returned.
Owner’s Manual Rev 1.0 Page 198 of 198 <ctrl-Z> (IRA 26) must be used to indicate the ending of the message body <da> Description String type GSM 03.
Owner’s Manual Rev 1.0 Page 199 of 199 13.8 AT+CMSS Send From Storage PDU mode Description Command Possible Responses Send from storage AT+CMSS=<index> •_ +CMSS: <mr> •_ +CMS ERROR: .
Owner’s Manual Rev 1.0 Page 200 of 200 Sends message with location value <index> from message storage <mem2> to the network (SMS-SUBMIT or SMS-COMMAND). Reference value <mr> is returned to the TE on successful message delivery. Optionally, when +CSMS <service> value is 1 and network support s, <scts> is returned.
Owner’s Manual Rev 1.0 Page 201 of 201 Send command message AT+CMGC=<length><CR> <pdu><ctrl-Z/ESC> •_ if PDU mode (+CMGF=0) and sending successful: +CMGC: <mr>[,<a.
Owner’s Manual Rev 1.0 Page 202 of 202 String GSM 03.40 RP-User-Data element of RP-ACK PDU; format is same as for <pdu> in case of SMS, but without GSM 04.
Owner’s Manual Rev 1.0 Page 203 of 203 Integer GSM 03.40 TP-Command-Type. Default value is 0 <pid> Description 0-255 Protocol Identifier in integer format. Default value is 0 , according to 07.05 section 9.2. 3.9 <mn> Description Integer GSM 03.
Owner’s Manual Rev 1.0 Page 204 of 204 ]]]] •_ ERROR Shows the current setting AT+CNMI? •_ +CNMI: <mode>,<mt>,<bm>,<ds> •_ OK •_ ERROR Show if the command is supporte.
Owner’s Manual Rev 1.0 Page 205 of 205 3 Class 3 SMS-DELIVERs are routed directly to TE usi ng unsolicite d resu lt code s +CMT: <length><CR><LF><pdu>.
Owner’s Manual Rev 1.0 Page 206 of 206 Show if the command is supported AT+CNMI=? •_ +CNMI: (list of supported <mode>s), (list of supported <mt>s), (list of supported <bm>s), (li.
Owner’s Manual Rev 1.0 Page 207 of 207 0 Store message to “BM” (or some manufacturer specific memory). No CBM indication s are routed to the TE 2 New CBMs are routed directly to the TE using uns.
Owner’s Manual Rev 1.0 Page 208 of 208 Show if the command is supported AT+CMGR=? •_ OK •_ ERROR Returns message with location value <index> from preferred message storage <mem1> to the TE. Status of the message and entire message data unit <pdu> is returned.
Owner’s Manual Rev 1.0 Page 209 of 209 Text Mode Description Command Possible Responses Read message AT+CMGR= [<index>] •_ if text mode (+CMGF=1), command successful and SMS-DELIVER: +CMGR: .
Owner’s Manual Rev 1.0 Page 210 of 210 <index> Description Integer type Value in the range of locati on numbers supported by <mem1> <stat> Description 0 Received unread message (ne.
Owner’s Manual Rev 1.0 Page 211 of 211 <alpha> Description String type Manufacturing sp ecific. Should be left e mpty but n ot omitted, i.e . commas shall ma rk the plac e were it s hould be. Used character set should be the one selected with command Select TE Character Set +CSCS <scts> Description String type GSM 03.
Owner’s Manual Rev 1.0 Page 212 of 212 2 First octet of SMS-STATUS-REP ORT in integer format 3 First octet of SMS-COMMAND in integer format <mr> Description Integer GSM 03.40 TP-Message_Reference <ra> Description String type GSM 03. 40 TP-Recipient-Address-Value fi eld.
Owner’s Manual Rev 1.0 Page 213 of 213 <sca> Description String type GSM 04. 11 RP SC address Address-Value fiel d in string format; BCD numbers (or GSM default alphabet characters) are converted to characters of the currently selected TE character set <tosca> Description Integer type GSM 04.
Owner’s Manual Rev 1.0 Page 214 of 214 Note!_ Returns messages with stat us value <stat> from preferred message storage <mem1> to the TE. Entire data units <pdu> are returned. If status of the message is ‘received unread’, status in the storage changes to ‘received read’.
Owner’s Manual Rev 1.0 Page 215 of 215 format Note!_ Text Mode Description Command Possible Responses List message AT+CMGL =[<stat>] •_ If text mode (+CMGF=1), command successful and SMS-SUB.
Owner’s Manual Rev 1.0 Page 216 of 216 +CMS ERROR: <err> Read the current setting •_ +CMGL:<stat> •_ +CMS ERROR: <err> Test if the command is supported AT+CMGL=? •_ +CMGL: (l.
Owner’s Manual Rev 1.0 Page 217 of 217 <stat> Description Integer Indicates the status of messages in memory 0 Received unread message (new message) 1 Received read message 2 Stored unsent mes.
Owner’s Manual Rev 1.0 Page 218 of 218 String type Manufacturing sp ecific. Should be left e mpty but n ot omitted i.e. commas shall mark the place were it shoul d be. Used character set should be the one selected with command Select TE Character Set +CSCS <scts> Description String type GSM 03.
Owner’s Manual Rev 1.0 Page 219 of 219 3 First octet of SMS-COMMAND in integer format <mr> Description Integer GSM 03.40 TP-Message-Reference <ra> Description String GSM 03.40 TP-Recipient-Address-Valu e field. BCD (or GSM default alphabet) are converted to characters of the currently selected TE character set (refef command +CSCS.
Owner’s Manual Rev 1.0 Page 220 of 220 <pages> Description Integer format GSM 03.41 CBM Page Parameter bits 0-3 i n integer format Example AT+CMGF=1 OK AT+CMGL=? +CMGL: “REC UNREAD”,“REC READ”, “STO UNSENT”,“STO SENT”,“ALL” OK 13.
Owner’s Manual Rev 1.0 Page 221 of 221 13.14 AT+CSDH Show Text Mode Parameters Only Applicable to Text Mode Description Command Possible Responses Set the show text mode AT+CSDH=[<show>] •_ .
Owner’s Manual Rev 1.0 Page 222 of 222 Show if the command is supported AT+CSMP=? •_ +CSMP: (Li st of supported <fo>s), (list of supported <vp>s), (list of supported <pid>s), (li.
Owner’s Manual Rev 1.0 Page 223 of 223 13.16 AT+CSCS Select Character Set Description Command Possible Responses Set command informs TA which character set is used by the TE AT+CSCS=<chset> .
Owner’s Manual Rev 1.0 Page 224 of 224 13.17 AT+CSMS Select Message Service Common for both PDU and Text Modes Description Command Possible Responses Select message service AT+CSMS=<service> .
Owner’s Manual Rev 1.0 Page 225 of 225 0 Mob ile origina ted mes sages n ot supp orted 1 Mobile originat ed mess ages s upport ed <bm> Description 0 Broadcast messages not supported 1 Broadcast messages supported <err> Description 0...127 GSM 04.
Owner’s Manual Rev 1.0 Page 226 of 226 Short Message Services - Cell Broadcast 14.1 AT+CNMI New Message Indications to TE See 13.10, AT+CNMI New Message Indications to TE 14.
Owner’s Manual Rev 1.0 Page 227 of 227 SIM Application Toolkit 15.1 AT+CPIN PIN Control See 3.23, AT+CPIN PIN Control 15.2 AT*E2STKS SIM Application Toolkit Settings Description Command Possible res.
Owner’s Manual Rev 1.0 Page 228 of 228 The unsolicited result codes defined in sections below can be received. 15.3 AT*E2STKD M2M STK Display Text Description Command Possible responses Answer to th.
Owner’s Manual Rev 1.0 Page 229 of 229 4 Faile d. Screen is busy: the text could not be displ ayed Unsolicited Result Codes: *E2STKD: <priority>,<clear_condition>,<coding>,<text_length>, <text> Values follow GSM 11.14 standard.
Owner’s Manual Rev 1.0 Page 230 of 230 Description Command Possible responses Answer to the reception of GET INKEY AT*E2STKG =<answer>, [<response_type>, <user_response>] •_ +CME.
Owner’s Manual Rev 1.0 Page 231 of 231 3 Faile d. No response from user: the text was displayed, and the user did not react. It corresponds to ‘12’ No response from user 4 Failed .
Owner’s Manual Rev 1.0 Page 232 of 232 15.5 AT*E2STKI M2M STK Get Input Description Command Possible responses Answer to the reception of GET INPUT AT*E2STKI=<answer >, [<response_type>,.
Owner’s Manual Rev 1.0 Page 233 of 233 2 Failed . User requests backward move: the text was displayed as requested and the user wants to go backwards in the session. It corresponds to ‘11’ backward move in the proactive SIM session requested by the user 3 Faile d.
Owner’s Manual Rev 1.0 Page 234 of 234 <max_length_response> Description Integer type (0-160) Value indicating the maximum length of response field <user_response> <echo_input> Des.
Owner’s Manual Rev 1.0 Page 235 of 235 •_ ERROR Test if the command is supported AT*E2STKL=? •_ *E2S TKL: (list of supported <answer>), (list of supported <user_response>) •_ +CME .
Owner’s Manual Rev 1.0 Page 236 of 236 integer type The identifier is a singl e byte between 1 and 255. It identifies the se lected <item_idn > within the items list Unsolicited Result Codes: .
Owner’s Manual Rev 1.0 Page 237 of 237 <itemn> Description String type Field of string type between “”. Codi ng is according to EF AND as defined in GSM 11.11 <NbrOfItems> Description Integer type Number of items to be presented i n the following unsolicit ed re sults The maximum length is fixed.
Owner’s Manual Rev 1.0 Page 238 of 238 0 OK. Performed as required: it corresponds to ‘00’ command performed successfully, described in the GSM standard 1 Faile d. User Terminated Session: the command was executed as requested and the user wants to end the proactive session.
Owner’s Manual Rev 1.0 Page 239 of 239 <text_length> Description Integer type Value indica ting the ma ximum length of field <alpha_id>, <itemn1>, <Itemn> <alpha_id> Description String type Fi eld of string type between "".
Owner’s Manual Rev 1.0 Page 240 of 240 Test if the command is supported AT*E2STKN=? •_ *E2STKN: (list of supported <sel_item>) •_ +CME ERROR <err> •_ OK •_ ERROR The application informs the ME about the selected menu item by means of the AT*E2SKTN command.
Owner’s Manual Rev 1.0 Page 241 of 241 <answer> Description 0 OK. Performed as required. It corresponds to ‘00’ command performed succesfully, described in the GSM standard 1 Faile d. User terminated session. It corresponds to ‘10’ Proactive session terminated by the user, described i n the GSM standard 2 Faile d.
Owner’s Manual Rev 1.0 Page 242 of 242 1 Text is coded in packed format, using the SMS default 7- bit coded alphabet, packed in 8-bi t octets, as defined in GSM 03.
Owner’s Manual Rev 1.0 Page 243 of 243 ‘FF’ In case that the SIM does not provide the optional alpha identifier , or this is a null data o bject, t he ME sha ll give ‘FF’ to indicate “Sending SMS”, so that the external applica tion is info rmed The maximum length is fixed.
Owner’s Manual Rev 1.0 Page 244 of 244 15.11 *E2STKP STK Send SS Unsolicited Result Code: *E2STKP: <ton>, <SS_string>, <coding>, <text_length>, <alpha_id>, <SS_return> The ME passes the parameters within SEND SS command to the external application, by means of the unsolicited result code *E2STKP.
Owner’s Manual Rev 1.0 Page 245 of 245 The maximum length is fixed. <SS_return> Description Integer type Field of 1 byte indicati ng the SS Return Result Operation code, as defined in GSM 04.80, so that the external applica tion is infor med ab out the r esult of the SS operation 15.
Owner’s Manual Rev 1.0 Page 246 of 246 15.13 *E2STKR STK Refresh Unsolicited Result Code: *E2STKR: <indicator> The ME informs the external application about the coming REFRESH command, by means of the unsolicited result code *E2STKR (eg Reset is coming).
Owner’s Manual Rev 1.0 Page 247 of 247 1 Set Up Menu command timeout is set to the value of <timer> 2 Set Up Call command timeout is set to the val ue of <timer> 3 Display Text command t.
Owner’s Manual Rev 1.0 Page 248 of 248 Supplementary Services 16.1 AT+CPIN PIN Control See 3.23, AT+CPIN PIN Control 16.2 AT+CACM Accumulated Call Meter Description Command Possible Responses Reset .
Owner’s Manual Rev 1.0 Page 249 of 249 16.3 AT+CAMM Accumulated Call Meter Maximum Description Command Possible Responses Set command sets the Advice of Charge related accumula ted call meter maximu.
Owner’s Manual Rev 1.0 Page 250 of 250 Execute command AT+CAOC[=<mode>] •_ [+CAOC: <ccm>] +CME ERROR: <err> •_ OK •_ ERROR Read command, shows the current mode AT+CAOC? •_ .
Owner’s Manual Rev 1.0 Page 251 of 251 16.5 AT+CPUC Price Per Unit and Currency Table Description Command Possible Responses Set command sets the parameters of Advice of Charge related price per uni.
Owner’s Manual Rev 1.0 Page 252 of 252 16.6 AT*EDIF Ericsson Divert Function Description Command Possible Responses Enable and disable notification with the unsolicit ed re sult cod e *EDIF AT*EDIF=.
Owner’s Manual Rev 1.0 Page 253 of 253 Read the current setting AT*EIPS? •_ *EIPS: <ID1>,<alphatag mode1><CR><LF> *EIPS: <ID2>,<alphatag mode2><CR><LF&.
Owner’s Manual Rev 1.0 Page 254 of 254 •_ ERROR Read the current line AT*ELIN? •_ *ELIN: <line> •_ +CME ERROR: <err> •_ OK •_ ERROR Test if the command is supported AT*ELIN=? .
Owner’s Manual Rev 1.0 Page 255 of 255 the operation executes successfully - use the AT*E2SSI command to gain feedback of the operation status. Refer to GSM 02.
Owner’s Manual Rev 1.0 Page 256 of 256 or *E2SSI: <errorcode>[,<Opcode>[,<SS_Code>,[<BasicServChoice>, <BasicServValue>],[<SS_Status>],[<SubscriptionOption>.
Owner’s Manual Rev 1.0 Page 257 of 257 33 CALL_FORWARDING_UNCONDITIONAL 40 ALL_CONDITIONAL_FORWARDING_SERVICES 41 CALL_FORWARDING_ON_MOBILE_SUBSCRIBER_BUSY 42 CALL_FORWARDING_ON_NO_REPLY 43 CALL_FOR.
Owner’s Manual Rev 1.0 Page 258 of 258 18 TS_EMERGENCY_CALLS BS_DATA_CDA_1200BPS 20 BS _DATA_CDA_2400BPS 21 BS_DATA_CDA_4800BPS 22 BS _DATA_CDA_9600BPS 24 BS_ALL_DATA_CDS _SERVICES 25 BS _DATA_CDS_3.
Owner’s Manual Rev 1.0 Page 259 of 259 120 BS_12_KBIT_UNRESTRICTED_DIGITAL 128 TS _ALL_TELESERVICES_EXCEPT_S MS 208 TS_AUXILIARY_SPEECH 209 TS_AUXILIARY_TELEPHONY <SS_Status> Description 0 NO_.
Owner’s Manual Rev 1.0 Page 260 of 260 Description Command Possible Responses Reque st Calling forwarding number and condit ions AT+CCFC=<reason>, <mode>[,<number> [,<type>[,.
Owner’s Manual Rev 1.0 Page 261 of 261 4 Erasure <number> Description string type String type phone number of forwarding address in format spe cified by <typ e> <type> Description integer format Type of address octet 129 ISDN/telephony numberi ng plan, national/international unknown.
Owner’s Manual Rev 1.0 Page 262 of 262 128 Dedicated PAD access <status> Description 0 Not active 1 Active 16.12 AT+CCWA Call Waiting Description Command Possible Responses Requ est ca ll wait.
Owner’s Manual Rev 1.0 Page 263 of 263 <n> Description 0 Disable 1 Enable <mode> Description 0 Disable 1 Enable 2 Query status <classx> Description integ er Sum of integers each representing a class of information.
Owner’s Manual Rev 1.0 Page 264 of 264 <err> Description 0 Phon e failure 3 Operation no t allowed 4 Operation not supported 21 Invalid index 30 No network service 31 Network timeout 100 Unknown Unsolicited Result Codes: +CCWA: <number>, <type>, <class> 16.
Owner’s Manual Rev 1.0 Page 265 of 265 command with other commands based on other GSM/UMTS supplementary services is described in the GSM/UMTS standards. Note!_ Call Hold and MultiParty are only applicable to teleservice 11. It is recommended (although optional) that test command returns a list of operations which are supported.
Owner’s Manual Rev 1.0 Page 266 of 266 Description Command Possible Responses Reque sts c alling line identification. AT+CLIP=<n> OK Read the current setting AT+CLIP? +CLIP: <n>,<m>.
Owner’s Manual Rev 1.0 Page 267 of 267 <type> Description 129 129 ISDN/tel ephony numbering plan, national/international unknown 145 145 ISDN/telephony numberi ng plan, international number 161 161 ISDN/telephony numberi ng plan, national number 128-255 Other values refer to GSM 04.
Owner’s Manual Rev 1.0 Page 268 of 268 Read command gives the default adjustment for all outgoing calls (given in <n>), and also triggers an interrogation of the provision status of the CLIR service (given in <m>). Test command returns values supported by the TA as a compound value.
Owner’s Manual Rev 1.0 Page 269 of 269 Test if the command is supported AT+CSSN=? •_ +CSSN: (list of supported <n>s),(list of supported <m>s) •_ +CME ERROR <err> •_ OK •_ ERROR This command refers to supplementary service related network initiated notifications.
Owner’s Manual Rev 1.0 Page 270 of 270 <code1> Description 0 Uncond itional ca ll forwardin g is active 1 Some of the conditio nal call forwa rding are active 2 Call has been forwarded 3 Call .
Owner’s Manual Rev 1.0 Page 271 of 271 Show supported message types along with the current service setting AT+CUSD? •_ +CUSD: <n> •_ OK •_ ERROR Show list of supported services AT+CUSD=?.
Owner’s Manual Rev 1.0 Page 272 of 272 2 Signal aski ng for reply Sends unsolicited result code +CUSD Result code presentation enabled, presented 3 Answer AT+CUSD 3b Sends AT+CUSD <n> Description 0 Disable result code presentati on in the TA 1 Enable result code presentation in the TA 2 Termina te (abo rt) USSD dialo gue.
Owner’s Manual Rev 1.0 Page 273 of 273 Example 2 AT Command Result Code Description +CUSD:0,“Expensive incoming ca ll” Incoming USSD- notify telling the user that the incoming call is expen sive.
Owner’s Manual Rev 1.0 Page 274 of 274 Alphabetical Listing of AT Commands AT Command Description Page No. AT Attention Command 131 AT&C Circuit 109 (DCD) Control 135 AT&D Circuit 108 (DTR) .
Owner’s Manual Rev 1.0 Page 275 of 275 AT*EAMS Eri csson Audio Mode Selection 100 AT*EARS Ericsson Audio Ring Signal 101 AT*ECAM Ericsson Call Monitoring 74 AT*ECPI Ciphering Indicator 165 AT*ECSP E.
Owner’s Manual Rev 1.0 Page 276 of 276 AT+CEER Extended Error Report 77 AT+CFUN Set Phone Functi onality 78 AT+CGACT PDP Context Activate or Deacti vate 109 AT+CGATT GPRS Attach or Detach 110 AT+CGD.
Owner’s Manual Rev 1.0 Page 277 of 277 AT+CMGF Message Format 184 AT+CMGL List Message 203 AT+CMGR Read Message 198 AT+CMGS Send Message 187 AT+CMGW Write Message to Memory 184 AT+CMOD Call Mode 66 AT+CMSS Send From Storage 190 AT+CMUX Switch to 07.
Owner’s Manual Rev 1.0 Page 278 of 278 AT+CSQ Signal Strength 89 AT+CSSN Supplementary S ervice Notification 255 AT+CTZU Automatic Time Zone Update 90 AT+CUSD Unstructured S upplementary Service Dat.
Owner’s Manual Rev 1.0 Page 279 of 279 ATZ Reset to Default Configuration 138 Unsolicited Result Code Description Page No. *E2STKE STK Send Short Message 230 *E2STKP STK Send SS 231 *E2STKR STK Refr.
Owner’s Manual Rev 1.0 Page 280 of 280 End of Document.
デバイスSony Ericsson TT4031 (SE-GM29)の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Sony Ericsson TT4031 (SE-GM29)をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSony Ericsson TT4031 (SE-GM29)の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Sony Ericsson TT4031 (SE-GM29)の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Sony Ericsson TT4031 (SE-GM29)で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Sony Ericsson TT4031 (SE-GM29)を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSony Ericsson TT4031 (SE-GM29)の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Sony Ericsson TT4031 (SE-GM29)に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSony Ericsson TT4031 (SE-GM29)デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
