SonyメーカーHKCU-904の使用説明書/サービス説明書
ページ先へ移動 of 74
HD CAMERA CONTROL UNIT HDCU-900 SD ANALOG INTERFACE UNIT HKCU-901 HD ANALOG INTERFACE UNIT HKCU-902 FRAME RATE CONVERTER UNIT HKCU-903 LINE CONVERTER UNIT HKCU-904 MAINTENANCE MANUAL 1st Edition (Revi.
HDCU-900 MM ! W ARNING This manual is intended for qualified service personnel only . T o reduce the risk of electric shock, fire or injury , do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.
HDCU-900 MM 1 (P) CLASS 1 LASER PRODUCT LASER KLASSE 1 PRODUKT This camera control unit is classified as a CLASS 1 LASER PRODUCT . The CLASS 1 LASER PRODUCT label is located on the rear panel.
.
1 (E) HDCU-900 MM Table of Contents Manual Structure Purpose of this manual ........................................................................................ 5 (E) Related manuals ................................................................
2 (E) HDCU-900 MM 2. Replacement of Main Parts 2-1. Replacing the Switching Regulator ....................................................... 2-1 (E) 2-2. Replacing the Fuse .............................................................................
3 (E) HDCU-900 MM 3-6. HD Signal Input/Output Adjustment (HKCU-902) ............................ 3-24 (E) 3-6-1. Y/P B /P R Output Level Adjustment ..................................... 3-24 (E) 3-6-2. GBR Output Level Adjustment .....................
.
5 (E) HDCU-900 MM Purpose of this manual This manual is the maintenance manual of the following models : HD Camera Control Unit HDCU-900 SD Analog Interface Unit HKCU-901 HD Analog Interface Unit HKCU.
6 (E) HDCU-900 MM Contents The following is a summary of the sections of this manual. Section 1 Service Overview Describes information about circuit description, on-board indicators, adjustments after board replacement and character display functions.
1-1 (E) HDCU-900 MM Section 1 Service Overview 1-1. Tools Name Sony P/N Remark Extension board BKP-7900 _ Front extension board Extension board JX-428 J-6394-280-A Front extension board Used to check side B of the board.
1-2 (E) HDCU-900 MM 1-2. Board/Main Parts Layout Switching regulator DC fans !- ! != ![ !] 1-2. Board/Main Parts Layout 1 2 3 4 6 7 9 8 5 0.
1-3 (E) HDCU-900 MM No. Board Function 1 SDI-54A board (HDCU-900) HD Digital Interface S/N : 10001- 11000 (UC), 40001- 41000 (CE) SDI-82 board (HDCU-900) S/N : 11001- (UC), 41001- (CE) 2 DIF-102 board.
1-4 (E) HDCU-900 MM 1-3. Circuit Description 1-3-1. HDCU-900 . AT-141 board The AT-141 board performs the various controls using the CPU, such as controlling the communication with the camera head, with the control panel and with the CNU, and the control of the respective circuit boards inside the CCU.
1-5 (E) HDCU-900 MM 1-3-2. HKCU-901 . IF-789A/789P board The IF-789A/789P board is used in combination with the RC-86 board for interfacing the SD signal of the main line using an analog interface.
1-6 (E) HDCU-900 MM 1-4. Functions of the Indicators on the Boards 1-4-1. AT-141 Board AT-141 board (A side and panel side) D609 : GEN LOCK display Lights up when external synchronization is established. D611 : /1.001 display Lights up when the frame frequency factor of the HD signal is set to 1/1.
1-7 (E) HDCU-900 MM D803, D805, D807, D810 : MAIN OUTPUT display Displays the frame frequency of the camera and the MAIN HD output of the CCU. D803 lights up when the frequency is 30 Hz. D805 lights up when the frequency is 25 Hz. D807 lights up when the frequency is 24 Hz.
1-8 (E) HDCU-900 MM Board suffix: -22 and later DPR-163 board (A side and panel side) n When D813 and D821 light in red, be sure to clean the CAMERA connector of the unit, the CCU connector of the camera side and optical/electrical cable. It is also recom- mended to clean them when the indicators light in yellow.
1-9 (E) HDCU-900 MM 1-4-3. RC-86 Board RC-86 board (A side and panel side) D4 : POWER display Lights up when the voltage used on the board is normally supplied. D809, D810, D811 : MAIN OUTPUT display Displays the SD system. D809 lights up when the SD system is set to 525/59.
1-10 (E) HDCU-900 MM 1-4-4. IF-789A/789P Board (HKCU-901) IF-789A/789P board (A side and panel side) D602 : BB REF IN display Lights up when the external sync mode is set to SD and the reference signal for synchronizing the sub carrier is input. n Set it with S602 on the AT-141 board.
1-11 (E) HDCU-900 MM D1006, D1007, D1008, D1009, D1010 : MAIN OUTPUT display Displays the frame frequency setting of the frame convert HD output of the CCU. D1006 lights up when the frequency is 30 Hz. D1007 lights up when the frequency is 25 Hz. D1008 lights up when the frequency is 24 Hz.
1-12 (E) HDCU-900 MM 1-5. Adjustment and Setting after Replacing the Boards After replacing each plug-in board, return the switches to the setting before replacement.
1-13 (E) HDCU-900 MM 1-6. Connecting/Disconnecting the Flexible Card Wire The flexible card wire is used to connect between the following boards. Bending the flexible card wire may result in shortening the lifespan. Be careful not to bend it. . Between the CN-2004 and PS-587 boards 1 wire .
1-14 (E) HDCU-900 MM 2. When the turn stops, pull out the remover in the straight line forcedly. n The alignment sleeve can be removed/reinstalled with the sleeve itself attached to the tip of the remover. Great care should be taken so as not to lose or damage the alignment sleeve.
1-15 (E) HDCU-900 MM 1-8. Notes for RX-53 Boards The electric parts mounted on the RX-53 board cannot be replaced or adjusted. If the electric parts need to be replaced or adjusted, replace the entire unit.
1-16 (E) HDCU-900 MM Data write procedure Data write procedure in the PLD (or ROM for PLD) is outlined below. For details of data write procedure, refer to “ Download Tool Operating Instruction for Device Program- ming ” .
1-17 (E) HDCU-900 MM 1-10. Circuit Protective Elements The positive characteristic thermistor (for power supply) functions as a circuit protective element on the AT-141, DPR-163, RC-86, IF-789A/789P (HKCU-901), FC-83 (HKCU-903) and LC-41 (HKCU-904) boards of the unit.
1-18 (E) HDCU-900 MM 1-11. Notes on Repair Parts 1. Safety Related Components Warning w Components marked ! are critical to safe operation. Therefore, specified parts should be used in the case of replacement. 2. Standardization of Parts Some repair parts supplied by Sony differ from those used for the unit.
1-19 (E) HDCU-900 MM 1-12. Character Display Function The character generation circuit built into the unit can mix character information such as the settings, state and self- diagnosis of the unit with the SD video signal, output it from the PIX OUT (RC-86 board output) and CHARAC- TER OUTPUT connectors, and display it on the SD analog monitor.
1-20 (E) HDCU-900 MM Page 1 System Status Display No. Contents 1 Displays the type of camera connected to the unit. (HDC-700/HDC-750/HDC-900/HDC-950/UNDEFINED) 2 Displays the type of external sync signal. (Free/SD Digital/HD Digital) 3 Displays the setup format of the DPR-163 board.
1-21 (E) HDCU-900 MM Page 4 SD Signal Status Display No. Contents 1 Setting state of the aspect ratio of the SD signal (SQ/LB/EC) SQ : Squeeze LB : Letter box EC : Edge crop Displays the crop position too. ( _ 99 to 99) _ 99 : The cut-out position is in the leftmost position.
1-22 (E) HDCU-900 MM Page 6 System Diag (2/3) Display No. Contents 1 State of camera cable connection (Open/Short/NG) 2 Existence of data from the camera ( __ /Wait/Sense/OK) __ : The communication with the camera cannot be established. Wait : The communication with the camera is being waited.
1-23 (E) HDCU-900 MM Page 9 DPR Diag Display Displays the details of self-diagnosis of the DPR-163 board of the unit. No. Contents 1 Whether the DPR-163 board is recognized (None/NG/OK) 2 Setting stat.
1-24 (E) HDCU-900 MM a. When the RC-86 board is mounted in the second or third slot from the top of the front side of the unit No. Contents 1 Whether the RC-86 board is recognized (None/NG/OK) b. When the FC-83 board is mounted in the second slot from the top of the front side of the unit No.
1-25 (E) HDCU-900 MM Page 12 Camera Diag Display HDC-700 SERIES HDC-900 SERIES Contents Displays the self-diagnosis result of the board on the camera side that is sent from the camera by the Diag command without change. Page 13 ROM Version (HDC-700 Series) Display Displays the ROM versions of the unit and the peripheral equipment of the unit.
.
2-1 (E) HDCU-900 MM Section 2 Replacement of Main Parts 2-1. Replacing the Switching Regulator w The components marked ! are critical to safe operation. If you replace with parts other than the specified ones, fire or electric shock may result. c When repairing or replacing the power supply block, set the voltage.
2-2 (E) HDCU-900 MM 2-2. Replacing the Fuse w The components marked ! are critical to safe operation. If you replace with parts other than the specified ones, fire or electric shock may result. Replacement Part n The CAMERA fuse differs depending on the destination of the unit.
2-3 (E) HDCU-900 MM 2-3. Removing the Rear Panel 1. Turn off the main power and disconnect the plug from the outlet. m . Wait for at least three minutes before starting replacement, because there are electrically live blocks inside the machine that could cause electric shock.
2-4 (E) HDCU-900 MM Replacing the upper fan 1. Disconnect the harness from the two harness clamps. 2. Disconnect the connector (CN23) from the PS-587 board. 3. Remove the four screws and remove the DC fan. 4. Attach a new DC fan in reverse order of steps 1 to 3.
2-5 (E) HDCU-900 MM 2-5. Replacing the PS-587 Board Replacement Procedure 1. Turn off the main power and disconnect the plug from the outlet. n Wait for at least three minutes before starting replace- ment, because there are electrically live blocks inside the machine that could cause electric shock.
2-6 (E) HDCU-900 MM 2-6. Replacing the RX-53 Board m . The electric parts mounted on the RX-53 board cannot be replaced or adjusted. If the electric parts need to be replaced or adjusted, replace the entire unit. . If you bend or pull out the optical fiber cable forcibly, disconnection may result.
2-7 (E) HDCU-900 MM 8. Remove the two screws (B3 x 5, shoulder screw) and remove the board assembly in the direction of the arrow. n Be careful not to bend the cables (especially light blue and cream color). 9. Attach the new RX-53 board assembly in reverse order of steps 3 to 8.
2-8 (E) HDCU-900 MM 2-7. Replacing the CAMERA Connector 2-7. Replacing the CAMERA Connector n If you bend or pull out the optical fiber cable forcibly, disconnection may result. Handle the cable carefully. Replacement Procedure 1. Follow steps 1 to 7 of Section 2-6, “Replacing the RX- 53 Board”.
3-1 (E) HDCU-900 MM Section 3 Electrical Alignment 3-1-2. Notes on Adjustments . The measure should have already been calibrated. . “3-1-4. Initialization Settings” have already been finished. . The adjustment of the HDC-900 (or HDC-950) haven already been finished.
3-2 (E) HDCU-900 MM 3-1-3. Connection of Equipment Adjusting the HDCU-900 Adjusting the HDCU-901 Adjusting the HDCU-902 OPTICAL FIBER CABLE CCA-5 CABLE (max. 200m) MASTER SETUP UNIT MSU-700A/750 STUDIO ZOOM LENS HD COLOR CAMERA HDC-900 HD CAMERA CONTROL UNIT HDCU-900 Measure OPTICAL FIBER CABLE CCA-5 CABLE (max.
3-3 (E) HDCU-900 MM 3-1-4. Initialization Settings HDCU-900 n When changing the switch settings from the customer ’ s setting positions, it is recommended to write down the customer ’ s setting positions in the following table. After completing the adjustment, be sure to return the switches to the customer ’ s setting positions.
3-4 (E) HDCU-900 MM 3-2. Audio System Adjustment 3-2-1. Microphone Level Adjustment Measures : Oscilloscope, Audio oscillator Note This adjustment is described on the premise that the output impedance of the audio oscillator is 600 Z . Preparation . Board extension : AT-141 board (front side) .
3-5 (E) HDCU-900 MM 3-2-2. Front Intercom Microphone Level Adjustment Measures : Oscilloscope, Audio generator Note This adjustment is described on the premise that the output impedance of the audio oscillator is 600 Z .
3-6 (E) HDCU-900 MM 3-2-3. RTS Intercom Adjustment Measures : Oscilloscope, Audio generator Note . This adjustment is described on the premise that the output impedance of the audio oscillator is 600 Z . . When the intercom system is the RTS system, perform this adjustment.
3-7 (E) HDCU-900 MM 3-2-4. PGM Mix Level Adjustment Measures : Oscilloscope, Audio oscillator Note This adjustment is described on the premise that the output impedance of the audio oscillator is 600 Z . Preparation Board extension : AT-141 board (front side) Adjustment Procedure 1.
3-8 (E) HDCU-900 MM 3-2-5. Side Tone Level Adjustment Measures : Oscilloscope, Audio oscillator Note This adjustment is described on the premise that the output impedance of the audio oscillator is 600 Z . Preparation . MIC switch/HDCU front panel → CARBON .
3-9 (E) HDCU-900 MM 3-3. Video and Reference Signal System Adjustment 3-3-1. HD-SDI Output VCO Free-run Adjustment Measure : Frequency counter Preparation . Board extension: AT-141 board (front side) . Remove the cable connected to the REFERENCE IN connector on the HDCU rear panel.
3-10 (E) HDCU-900 MM 3-3-3. Clock (74 MHz) Duty Adjustment/DPR Board Perform “ 3-3-2. Clock (74MHz) Duty Adjustment/AT Board ” before starting this adjustment. Measure : Oscilloscope (20 MHz BWLimit: ON) Note This adjustment corresponds to the DPR-163 board with part No.
3-11 (E) HDCU-900 MM 3-4. Video Signal System Adjustment (RC-86 Board) 3-4-1. SD-SDI Output VCO Adjustment Measure : Frequency counter Note After replacing IC508 or IC510 on the RC-86 board only, perform this adjustment. Preparation . Board extension : RC-86 board (front side) .
3-12 (E) HDCU-900 MM 3-4-2. SD-SDI Input VCO Free-run Adjustment Measure : Frequency counter Note After replacing IC601 on the RC-86 board only, perform this adjustment. Preparation . Board extension : RC-86 board (front side) . S110 (L-8)/AT-141 → LOCAL .
3-13 (E) HDCU-900 MM 3-4. Video Signal System Adjustment (RC-86 Board) 3-4-3. Main Clock (74 MHz) Duty Adjustment Measure : Oscilloscope (20 MHz BWLimit: ON) Note This adjustment corresponds to the RC-86 board with part No.
3-14 (E) HDCU-900 MM 3-4. Video Signal System Adjustment (RC-86 Board) 3-4-5. PIX Output Level Adjustment Measures : Oscilloscope, SD waveform monitor Preparation . Board extension : RC-86 board (front side) . Board extension : DIF-102 board (rear side) .
3-15 (E) HDCU-900 MM 3-4-6. WF Output Level Adjustment Measures : Oscilloscope, SD waveform monitor Preparation . Board extension : RC-86 board (front side) . Board extension : DIF-102 board (rear side) . 1 RV354 (B-4)/RC-86 → mechanical center (ENC LEVEL) .
3-16 (E) HDCU-900 MM 3-5. SD Signal System Adjustment (HKCU-901) Preparation . Board extension : IF-789A/789P board (front side) . S101-1 (M-9)/IF-789A/789P → ON . S101-2 (M-9)/IF-789A/789P → SMPTE . S708-1 (M-8)/IF-789A/789P → ON (CLEAR) . S201 (M-9)/IF-789A/789P → OFF .
3-17 (E) HDCU-900 MM 3-5-1. VBS Output Level Adjustment Measures : SD waveform monitor, Vector monitor Preparation Board extension : VDA-57 board (rear side) Adjustment Procedure 1.
3-18 (E) HDCU-900 MM 3-5-3. WF Output Level Adjustment Measure : SD waveform monitor Preparation . The VBS output level adjustment (section 3-5-2) should be completed. . WF monitor select switch/MSU → ENC . Board extension : VDA-57 board (rear side) Adjustment Procedure 1.
3-19 (E) HDCU-900 MM 3-5-4. GRB Output Level Adjustment Measure : SD waveform monitor Preparation Board extension : VDA-57 board (rear side) Adjustment Procedure 1.
3-20 (E) HDCU-900 MM 3-5-5. Y/R-Y/B-Y Output Level Adjustment Measure : SD waveform monitor Preparation . The GRB output level adjustment (section 3-5-4) should be completed. . Board extension : VDA-57 board (rear side) . S705 (M-8)/IF-789A/789P → YCD .
3-21 (E) HDCU-900 MM 5. R-Y signal level adjustment Measuring point : R-Y/R OUTPUT connector/VDA-57 Adjusting point : 1 RV213 (C-7)/IF-789A/789P Specifications : D = 700 ± 5 mV p-p (SET UP : ON) (75% (R-Y) color bar) (for UC) D = 525 ± 5 mV p-p (75% (R-Y) color bar) (for CE) 6.
3-22 (E) HDCU-900 MM 1. Input Level Adjustment Adjustment Procedure Measuring point : TP405 (G-4)/IF-789A/789P Adjusting point : 1 RV401 (G-4)/IF-789A/789P Specifications : A = 1.56 ± 0.02 V p-p 2. Phase Adjustment Adjustment Procedure Measuring point : TP503 (G-1)/IF-789A/789P Adjusting point : 1 RV404 (L-3)/IF-789A/789P Specifications : B = 0 3.
3-23 (E) HDCU-900 MM 4. Return Level Adjustment (Pr) Adjustment Procedure 1. CONFIG button/MSU → ON Set using MSU on the touch panel as follows. [ CCU] → [RET|SETTING] → RET1 : 2nd Slot (DIF-RET-1) 2. Measuring point : TP31/extension board (VDA-55) Measure level F.
3-24 (E) HDCU-900 MM 3-6. HD Signal Input/Output Adjustment (HKCU-902) 3-6. HD Signal Input/Output Adjustment (HKCU-902) 3-6-1. Y/P B /P R Output Level Adjustment Measure : HD waveform monitor Preparation . Board extension : ADA-59 board (rear side) .
3-25 (E) HDCU-900 MM 3-6. HD Signal Input/Output Adjustment (HKCU-902) 3-6-2. GBR Output Level Adjustment Measure : HD waveform monitor Preparation . The Y/P B /P R output level adjustment (section 3-6-1) should be completed. . Board extension : ADA-59 board (rear side) .
3-26 (E) HDCU-900 MM 3-6. HD Signal Input/Output Adjustment (HKCU-902) 5. R mix level adjustment Measuring point : P R /R OUTPUT1 connector/ ADA-59 Adjusting point : 1 RV302 (L-4)/ADA-59 Specifications : Portion G and portion H must be flat (within 5 mV or less).
3-27 (E) HDCU-900 MM 3-6. HD Signal Input/Output Adjustment (HKCU-902) 3-6-4. A/D Conversion Level Adjustment Measure : Oscilloscope Note Do not connect anything to the VTR connector of the camera. Preparation . The Y/P B /P R output level adjustment (section 3-6-1) should be completed.
3-28 (E) HDCU-900 MM 3-7. Video Signal Sytem Adjustment (HKCU-904) 3-7. Video Signal Sytem Adjustment (HKCU-904) 3-7-1. Main Clock (74 MHz) Duty Adjustment Measure : Oscilloscope (20 MHz BWLimit: ON) Preparation .
HDCU-900 MM SAFETY CHECK-OUT After correcting the original service problem, perform the following safety checks before releasing the set to the customer : Check the metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage.
Printed in Japan Sony Corporation 2003. 6 16 B&P Company ©2000 HDCU-900 (UC, J, CE) HKCU-901 (UC, J, CE) HKCU-902 (SY) HKCU-903 (SY) HKCU-904 (SY) J, E 9-968-566-03.
デバイスSony HKCU-904の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Sony HKCU-904をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはSony HKCU-904の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Sony HKCU-904の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Sony HKCU-904で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Sony HKCU-904を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はSony HKCU-904の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Sony HKCU-904に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちSony HKCU-904デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。